Page 1 V10.1.00...
Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Information contained herein is for reference only and does not constitute a commitment on the part of the manufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Eup-Standby And Off Mode Power Consumption Statement
Preface R&TTE Directive This device is in compliance with the essential requirements and other relevant provisions of the R&TTE Direc- tive 1999/5/EC. This device will be sold in the following EEA countries: Austria, Italy, Belgium, Liechtenstein, Denmark, Lux- embourg, Finland, Netherlands, France, Norway, Germany, Portugal, Greece, Spain, Iceland, Sweden, Ireland, United Kingdom, Cyprus, Czech Republic, Estonia, Hungary, Latvia, Lithuania, Malta, Slovakia, Poland, Slov- enia.
Page 5 Preface CE Marking This device has been tested to and conforms to the regulatory requirements of the European Union and has at- tained CE Marking. The CE Mark is a conformity marking consisting of the letters “CE”. The CE Mark applies to products regulated by certain European health, safety and environmental protection legislation.
Page 6: Fcc Statement
Preface FCC Statement (Federal Communications Commission) You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
Page 7: Fcc Rf Radiation Exposure Statement
Preface FCC RF Radiation Exposure Statement: This Transmitter must not be co-located or operating in conjunction with any other antenna or transmitter. This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 centimeters between the radiator and your body.
Page 8: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 9: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be damaged. Do not expose the computer Do not place it on an unstable Do not place anything heavy...
Page 10 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 11: Power Safety
Preface Power Safety The computer has specific power requirements:  • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety steady, uninterrupted power supply. If you are unsure of your local power specifications, Warning consult your service representative or local power company.
Page 12: Polymer Battery Precautions
Preface Polymer Battery Precautions Note the following information which is specific to polymer batteries only, and where applicable, this overrides the general battery precaution information overleaf. • Polymer batteries may experience a slight expansion or swelling, however this is part of the battery’s safety mecha- nism and is not a cause for concern.
Page 13: General Battery Precautions
Preface General Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the computer. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way. Even if the computer continues to work with a damaged battery in place, it may cause circuit damage, which may possibly result in fire.
Page 14: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 15: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 16 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshooting, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 17 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 18: Lcd Screen Care
Preface Lighting Proper lighting and a comfortable viewing angle can reduce eye strain and shoulder and neck muscle fatigue. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly. •...
Page 19: Table Of Contents
Preface Contents Notice .................I System Map: LCD Panel Open - Model C ....1-8 EuP-Standby and Off Mode Power Consumption State- LED Indicators ...............1-9 ment: .................II Keyboard ..............1-10 FCC Statement ..............IV Function Keys & Visual Indicators ......1-11 FCC RF Radiation Exposure Statement: ......V System Map: Front &...
Page 20 Preface Multi-in-1 Card Reader ..........2-6 Battery Information ............3-10 Audio Features ...............2-7 Conserving Battery Power ...........3-11 Setup for Audio Recording ..........2-8 Battery Life ..............3-12 Setup for 5.1 or 7.1 Surround Sound ......2-9 New Battery ..............3-12 Audio Notes for Model C Computers (Fn + 5) ...2-11 Recharging the Battery with the AC/DC Adapter ..3-12 TouchPad and Buttons/Mouse ........2-12 Proper handling of the Battery Pack ......3-13...
Page 21 Preface MEI Driver ..............4-7 System/Extended Memory: (Main Menu) .....5-7 Audio ................4-7 MB Series / BIOS Revision / KBC/ Windows Experience Index ...........4-8 EC firmware Revision / VGA Card etc. (Main Menu) ..5-7 Optional Drivers ............4-9 Advanced Menu .............5-8 PC Camera ..............4-10 Advanced Chipset Control (Advanced Menu) ....5-8 Wireless LAN ..............4-10 Bluetooth Power Setting (Advanced Menu >...
Page 22 Preface Upgrading the System Memory (RAM) ......6-14 Data Transfer Configuration ........7-39 Replacing the Primary System Memory Modules ..6-15 Windows Mobility Center ...........7-41 Fingerprint Reader Module ..........7-42 Modules Fingerprint Reader Driver Installation ......7-43 User Enrollment ............7-44 Overview ................7-1 Fingerprint Control Center Features ......7-47 Setting Up SATA RAID Mode ........7-2 Bluetooth Module ............7-48 AHCI Mode ..............7-2...
Page 23 Preface TV Tuner Module ............7-85 Interface (Ports & Jacks) Consumer Infrared Driver ..........7-86 Overview ...............A-1 Digital TV Broadcast Signal ........7-87 Ports and Jacks ..............A-2 TV Recording and Power Plans ........7-87 Card Reader ..............A-2 Remote Control Unit ............7-87 Cable (CATV) Antenna Jack (Model C Only) .....A-2 THX TruStudio Pro Audio ..........7-88 Consumer Infrared Transceiver ........A-2 THX TruStudio AP Installation ........7-88...
Page 24 Preface Attaching Other Displays (Win 7) ......B-10 Environmental Spec ............C-6 Physical Dimensions & Weight ........C-6 Specifications Processor ............... C-2 Processor ............... C-2 Processor ............... C-2 Core Logic ..............C-2 Memory ................. C-3 Display ................C-3 Video Adapter Options ..........C-3 Video Adapter Options ..........
Page 25: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 26: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “Drivers & Utilities” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 27: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows 7) and applications (e.g. word processing, spreadsheet and database programs) have their own manuals, so please consult the appropriate manuals.  Drivers If you are installing new system software, or are re-configuring your computer for a different system, you will need to install the appropriate drivers.
Page 28: System Software
Quick Start Guide System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find the Windows 7 operating system is sup- ported.
Page 29: Model Differences
Quick Start Guide Model Differences This notebook series includes three different model types that mainly differ as indicated in the table below. Note that your model may appear slightly different from those pictured in this manual. Feature Model A Model B Model C Rubber Style Paint Standard Paint...
Page 30: System Startup
Quick Start Guide System Startup 1. Remove all packing materials, and place the computer on a stable surface. 2. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. 3. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 31: System Map: Lcd Panel Open - Models A & B
Quick Start Guide System Map: LCD Panel Open - Models A & B Figure 1 - 2 LCD Panel Open  1. Built-In PC Camera 2. LCD Wireless Device 3. LED Lock Indicators Operation Aboard 4. Power Button Aircraft 5. Speakers 6.
Page 32: System Map: Lcd Panel Open - Model C
Quick Start Guide System Map: LCD Panel Open - Model C Figure 1 - 3 LCD Panel Open  1. Built-In PC Camera Wireless Device 2. LCD Operation Aboard 3. Speakers Aircraft 4. LED Indicators 5. Power Button The use of any portable 6.
Page 33: Led Indicators
Quick Start Guide LED Indicators Icon Color Description The LED indicators display helpful information about the current status of the computer. Orange The Battery is Charging Color Models Color Blinking The Battery has Reached Icon Description A & B Model C Orange Critically Low Power Status Number Lock is...
Page 34: Keyboard
Quick Start Guide Keyboard  The keyboard has an embedded numerical keypad for easy numeric data input, and Other Keyboards features function keys to allow you to change operational features instantly. See Table 1 - 4, on page 1 - 11 for full function key combination details.
Page 35: Function Keys & Visual Indicators
Quick Start Guide Function Keys & Visual Indicators The function keys (F1 - F12 etc.) will act as hot keys when pressed while the Fn key is held down. In addition to the basic function key combinations; visual indicators (see the table below) are available when the Hot Key driver is installed.
Page 36: System Map: Front & Rear Views
Quick Start Guide System Map: Front & Rear Views Figure 1 - 5 Front View Models A & B 1. LED Power Indica- tors 2. Vent/Fan Intake Models A & B 3. eSATA/USB 2.0 Combo Port 4. HDMI-Out Port 5. DVI-Out Port 6.
Page 37: System Map: Right View
Quick Start Guide System Map: Right View Figure 1 - 6 Figure 1 - 7 Right View Right View Models A & B 1. Optical Device 1. Optical Device Drive Bay Drive Bay 2. Headphone Jack 2. Headphone Jack 3. Microphone Jack 3.
Page 38: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 8 Left View Models A & B 1. RJ-45 LAN Jack 2. 2 * USB 3.0 Ports 3. 1 * USB 2.0 Port 4. Mini-IEEE 1394a Port Model C 5. Multi-in-1 Card Reader 6.
Page 39: System Map: Bottom View - Models A & B
Quick Start Guide System Map: Bottom View - Models A & B Figure 1 - 9 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. HDD Bay 5. Battery  Overheating  To prevent your comput- Battery Information er from overheating make sure nothing blocks the...
Page 40: System Map: Bottom View - Model C
Quick Start Guide System Map: Bottom View - Model C Figure 1 - 10 Bottom View 1. Sub Woofer 2. Fan Outlet/Intake 3. Component Bay Cover 4. Primary HDD Bay 5. Secondary HDD 6. Battery 7. Speakers  6 6 7 Overheating ...
Page 41: Windows 7 Start Menu & Control Panel
Quick Start Guide Windows 7 Start Menu & Control Panel Most of the control panels, utilities and programs within Windows 7 (and most other Windows versions) are ac- cessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 42: Video Features
Quick Start Guide Video Features You can switch display devices, and configure display options, from the Display control panel (in Appearances and Personalization) in Windows 7. To access Display (Control Panel) and Screen Resolution in Windows: Click Start and click Control Panel. Click Display (icon) - In the Appearances and Personalization category.
Page 43: Screen Resolution
Quick Start Guide Screen Resolution  Video Options Note that card types, specifica- tions and drivers are subject to continual updates and changes. Check with your service center for the latest details on video cards supported. Figure 1 - 12 - Screen Resolution Video Features 1 - 19...
Page 44: Nvidia Control Panel
Quick Start Guide NVIDIA Control Panel You can access the NVIDIA Control Panel as follows: Click Start, and click Control Panel. Click NVIDIA Control Panel (Figure 1 - 13) - In the Appearances and Personalization category. “NVIDIA Video Driver Controls” on page B - 1 for full details on control panels etc.
Page 45: Power Options
Quick Start Guide Power Options The Power Options (Hardware and Sound menu) control panel icon in Windows (see page 16) allows you to configure power management features for your computer. You can conserve power by means of power plans and configure the options for the power button, sleep button, computer lid (when closed), display and sleep mode from the left menu.
Page 46 Quick Start Guide 1 - 22...
Page 47: Storage Devices, Mouse, Audio & Printer
Storage Devices, Mouse, Audio & Printer Chapter 2: Storage Devices, Mouse, Audio & Printer Overview Read this chapter to learn more about the following main features and components of the computer: • Hard Disk Drive • Optical Device • Multi-in-1 Card Reader •...
Page 48: Hard Disk Drive
Storage Devices, Mouse, Audio & Printer Hard Disk Drive  The hard disk drive(s) is used to store your data in the computer. The hard disks) can Power Safety be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm.
Page 49: Optical Device
Storage Devices, Mouse, Audio & Printer Optical Device  There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The actual de- Sound Volume vice will depend on the model you purchased (see “Storage” on page C - 4).
Page 50: Handling Cds Or Dvds
Storage Devices, Mouse, Audio & Printer Handling CDs or DVDs  Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/DVDs can be CD Emergency Eject accessed.
Page 51: Dvd Regional Codes
Storage Devices, Mouse, Audio & Printer DVD Regional Codes  To change the DVD regional codes: DVD Region Note Go to the Control Panel Double-click Device Manager (Hardware and Sound), then click the + next to DVD region detection is DVD/CD-ROM drives.
Page 52: Multi-In-1 Card Reader
Storage Devices, Mouse, Audio & Printer Multi-in-1 Card Reader  The card reader allows you to use some of the latest digital storage cards. Push the Card Reader Cover card into the slot and it will appear as a removable device, and can be accessed in the same way as your hard disk (s).
Page 53: Audio Features
Storage Devices, Mouse, Audio & Printer Audio Features  You can configure the audio options on your computer from the Sound control Volume Adjustment panel in Windows, or from the Realtek HD Audio Manager icon in the taskbar/ control panel (right-click the taskbar icon to bring up an audio menu).
Page 54: Setup For Audio Recording
Storage Devices, Mouse, Audio & Printer Setup for Audio Recording To record audio sources on your computer at optimum quality follow the instruc- tions below: Click Start, and click Control Panel (or point to Settings and click Control Panel) and make sure you are in Classic View. Click Realtek HD Audio Manager (or right-click the taskbar icon and select Sound Manager).
Page 55: Setup For 5.1 Or 7.1 Surround Sound
Storage Devices, Mouse, Audio & Printer Setup for 5.1 or 7.1 Surround Sound  To setup your system for 5.1 or 7.1 surround sound you will need to connect the au- dio cables to the Headphone-Out, Line-In, Microphone-In jack and S/PDIF-Out THX Audio &...
Page 56 Storage Devices, Mouse, Audio & Printer Plug the front speaker cables into the Headphone-Out Jack. Plug in the other cables (you may require an adapter to connect each cable to the appropriate jack e.g a stereo mini to dual RCA adapter) from your speakers as follows: •...
Page 57: Audio Notes For Model C Computers (Fn + 5)
Storage Devices, Mouse, Audio & Printer Audio Notes for Model C Computers (Fn + 5) Model C computers (Model C only) feature the Fn +5 key combination to toggle between standard audio and enhanced audio. Note the following which applies to software mode audio configuration through the computer’s internal speakers only (this does not apply to surround sound when configured through external Qua- drophonic, 5.1 or 7.1 speaker systems):...
Page 58: Touchpad And Buttons/Mouse
Storage Devices, Mouse, Audio & Printer TouchPad and Buttons/Mouse  The TouchPad is an alternative to the mouse; however, you can also add a mouse to Mouse Driver your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse.
Page 59 Storage Devices, Mouse, Audio & Printer Once you have installed the TouchPad driver (see “TouchPad” on page 4 - 7) you  can configure the functions from the Mouse control panel in Windows, or by double- clicking the TouchPad driver icon on the taskbar.
Page 60: Gestures And Device Settings
Storage Devices, Mouse, Audio & Printer Gestures and Device Settings  The Synaptics Gestures Suite application allows you to use a specific gesture (ac- Show Video tion) on the surface of the TouchPad to perform specific actions to manipulate doc- uments, objects and applications.
Page 61 Storage Devices, Mouse, Audio & Printer Scrolling The Two-Finger scrolling feature works in most scrollable windows and allows you to scroll horizontally and vertically. Place two fingers, slightly separated, on the TouchPad surface and slide both fingers in the direction required (in a straight con- tinuous motion).
Page 62 Storage Devices, Mouse, Audio & Printer Rotating Use the Pivot Rotate gesture to rotate objects (e.g. photos) in 90 degree increments. Place a finger down on the left “target” zone and keep it stationary. Place another finger near the middle of the TouchPad and slide it in a circular motion around the stationary finger (clockwise or counterclockwise) to rotate the object.
Page 63: Adding A Printer
Storage Devices, Mouse, Audio & Printer Adding a Printer  The most commonly used peripheral is a printer. The following conventions will Parallel Printer help you to add a printer; however it is always best to refer to the printer manual for specific instructions and configuration options.
Page 64 Storage Devices, Mouse, Audio & Printer 2 - 18...
Page 65: Power Management
Power Management Chapter 3: Power Management  Overview OS Note Power management To conserve power, especially when using the battery, your computer power man- functions will vary slight- agement conserves power by controlling individual components of the computer ly depending on your (the monitor and hard disk drive) or the whole system.
Page 66: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/ DC adapter will damage the computer and its components (see page Attach the AC/DC adapter to the DC-In jack at the rear of the computer.
Page 67: Turning On The Computer
Power Management Turning On the Computer  Now you are ready to begin using your computer. To turn it on simply press the pow- Forced Off er button on the front panel. If the system “hangs”, When the computer is on, you can use the power button as a Stand by/Hibernate/ and the Ctrl + Alt + Del Shutdown hot-key button when it is pressed for less than 4 seconds (pressing and key combination doesn’t...
Page 68: Power Plans
Power Management Power Plans  The computer can be configured to conserve power by means of power plans. You Resuming can use (or modify) an existing power plan, or create a new one. Operation The settings may be adjusted to set the display to turn off after a specified time, and Table 3 - 1, on to send the computer into Sleep after a period of inactivity.
Page 69 Power Management Each Windows power plan will also adjust the processor performance of your ma- chine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose High performance (you may need to click Show additional plans to view the High performance plan) for maximum performance when the computer is pow- ered from an AC power source.
Page 70: Power-Saving States
Power Management Power-Saving States You can use power-saving states to stop the computer’s operation and restart where you left off. Win 7 uses the Sleep, Hibernate and Shut Down power-saving states. Sleep In Sleep all of your work, settings and preferences are saved to memory before the system sleeps.
Page 71: Hibernate
Power Management Hibernate Hibernate uses the least amount of power of all the power-saving states and saves all of your information on a part of the hard disk before it turns the system off. If a power failure occurs the system can restore your work from the hard disk; if a power failure occurs when work is saved only to memory, then the work will be lost.
Page 72: Configuring The Power Buttons
Power Management Configuring the Power Buttons  The power/sleep button (Fn + F4 key combo) and closed lid may be set to send the Password computer in to a power-saving state. Click Choose what the power buttons do on Protection the left menu in Power Options to bring up the menu.
Page 73: Resuming Operation
Power Management Resuming Operation  You can resume operation from power-saving states by pressing the power button, or in some cases pressing the sleep button (Fn + F4 key combo). Closing the Lid If you have chosen to Power Status Icon Color To Resume...
Page 74: Battery Information
Power Management Battery Information  Follow these simple guidelines to get the best use out of your battery. Low Battery Battery Power Warning Your computer’s battery power is dependent upon many factors, including the pro- When the battery is criti- grams you are running, and peripheral devices attached.
Page 75: Conserving Battery Power
Power Management Conserving Battery Power  • Use a power plan that conserves power (e.g Power saver), however note that this may have an affect on computer performance. Wireless Hot Keys • Lower the brightness level of the LCD display. The system will decrease LCD The computer’s wireless brightness slightly to save power when it is not powered by the AC/DC adapter.
Page 76: Battery Life
Power Management Battery Life Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. We recommend that you do not remove the battery yourself. If you do need to re- move the battery for any reason (e.g.
Page 77: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack  • DO NOT disassemble the battery pack under any circumstances. • DO NOT expose the battery to fire or high temperatures, it may explode. Caution • DO NOT connect the metal terminals (+, -) to each other. Danger of explosion if battery is incorrectly re- ...
Page 78: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Don’t turn off the computer even if a message indicates the battery is critically low, just let the computer use up all of the battery power and shut down on its own.
Page 79 Power Management Click Change plan settings (after creating it) and click Change plan settings > Change advanced power settings. Figure 3 - 8 Change Plan Settings / Change Advanced Power Settings Battery Information 3 - 15...
Page 80 Power Management Scroll down to Battery and click + to expand the battery options. Choose the options below (click Yes if a warning appears): Figure 3 - 9 Power Options Advanced Settings - Battery • Low battery levels = 0% •...
Page 81 Power Management How do I fully charge the battery? When charging the battery, don’t stop until the LED charging indicator light changes from orange to green. How do I maintain the battery? Completely discharge and charge the battery at least once every 30 days or after about 20 partial discharges.
Page 82 Power Management 3 - 18...
Page 83: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utili- ties essential to the operation or improvement of some The Device Drivers & Utilities + User’s Manual disc of the computer’s subsystems. The system takes ad- contains the drivers and utilities necessary for the vantage of some newer hardware components for proper operation of the computer.
Page 84: Driver Installation
Drivers & Utilities Driver Installation Check the driver installation order from Table 4 - 1, on page 4 - 3 (the drivers must be installed in Insert the Device Drivers & Utilities + User’s Manual this order) which is the same as that listed in the disc and click Install Drivers (button), or Option Driv- Drivers Installer menu below.
Page 85 Drivers & Utilities Windows 7 Driver Page Windows 7 Driver Page Chipset Page 4 - 6 PC Camera Module Page 7 - 15 Video (VGA) Page 4 - 6 Wireless LAN Module Page 7 - 23 Page 4 - 6 Fingerprint Reader Module Page 7 - 42 Card Reader...
Page 86: Manual Driver Installation
Drivers & Utilities Manual Driver Installation Updating/Reinstalling Individual Drivers Click the Browse CD/DVD button in the Drivers In- If you wish to update/reinstall individual drivers it staller application and browse to the executable file in may be necessary to uninstall the original driver.To do the appropriate driver folder.
Page 87: User Account Control
Drivers & Utilities User Account Control New Hardware Found If a User Account Control prompt appears as part of If you see the message “New Hardware Found” dur- the driver installation procedure, click Continue/Al- ing the installation procedure (other than when out- low, and follow the installation procedure as directed.
Page 88: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure Video (VGA) Insert the Device Drivers & Utilities + User’s Manual 1. Click 2.Install VGA Driver > Yes. disc and click Install Drivers (button), or Option Driv- 2. Click AGREE AND CONTINUE (button) to ers (button) to access the Optional driver menu.
Page 89: Card Reader
Drivers & Utilities Card Reader 3. Click the button to accept the license and then click Next. 1. Click 4.Install Cardreader Driver > Yes. 4. Click Install > Finish. 2. Click Install. 3. Click Finish to complete the installation. MEI Driver TouchPad 1.
Page 90: Windows Experience Index
Drivers & Utilities Windows Experience Index It is recommended that you install the THX Tru Stu- dio Pro Audio application (see “THX TruStudio AP After Video (VGA) driver has been installed, and the Installation” on page 7 - 88) and Intel Rapid Storage system restarted, the OS will automatically run the Technology driver (see “IRST Driver Installation”...
Page 91: Optional Drivers
Drivers & Utilities Optional Drivers See the pages indicated for the driver installation procedures for any modules included in your purchase option. Models A & B Model C Figure 4 - 3 - Optional Drivers Installer Screen Note that for Intel and 3rd party WLAN & Bluetooth Combo modules you need to install both the WLAN & Bluetooth drivers.
Page 92: Pc Camera
Drivers & Utilities PC Camera Consumer Infrared (for TV Tuner Remote - See the install procedure in “PC Camera Module” on Model C Only) page 7 - See the install procedure in “TV Tuner Module” on page 7 - Wireless LAN See the appropriate install procedure for your WLAN THX TruStudio AP module in...
Page 93: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities  Overview BIOS Screens Note that BIOS This chapter gives a brief introduction to the computer’s built-in software: screens pictured these pages are intend- Diagnostics: The POST (Power-On Self Test) ed for guidance in set- ting up your system’s BIOS.
Page 94: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) If you enable the Boot-time Diagnostic Screen in the Setup Utility, each time you turn on the computer the system takes a few seconds to conduct a POST, including a quick test of the on-board RAM (memory). As the POST proceeds, the computer will tell you if there is anything wrong.
Page 95: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non- fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 96: The Setup Utility
BIOS Utilities The Setup Utility  The Aptio Setup Utility tells the system how to configure itself and manage basic BIOS Settings features and subsystems (e.g. port configuration). Warning Entering Setup Incorrect settings can cause your system to To enter Setup, turn on the computer and press F2 (and give the system a few sec- malfunction.
Page 97: Setup Screens
BIOS Utilities Setup Screens  The following pages contain additional advice on portions of the Setup. Along the top of the screen is a menu bar with menu headings. When you select a heading, a Setup Menus new screen appears. Scroll through the features listed on each screen to make chang- Setup menus es to Setup.
Page 98: Main Menu
BIOS Utilities Main Menu Figure 5 - 2 Main Menu System Time & Date (Main Menu) The hour setting uses the 24-hour system (i.e., ØØ = midnight; 13 = 1 pm). If you can change the date and time settings in your operating system, you will also change these settings.
Page 99: Sata Port 0/2/3 (Main Menu)
BIOS Utilities SATA Port 0/2/3 (Main Menu) Pressing Enter opens the sub-menu to show the configuration of a optical Device/ HDD on the computer’s SATA Ports. System/Extended Memory: (Main Menu) This item contains information on the system memory, and is not user configurable. The system will auto detect the amount of memory installed.
Page 100: Advanced Menu
BIOS Utilities Advanced Menu Figure 5 - 3 Advanced Menu Advanced Chipset Control (Advanced Menu) The sub-menu here allows you to adjust the Bluetooth Power Setting. 5 - 8 Advanced Menu...
Page 101: Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)
BIOS Utilities Bluetooth Power Setting (Advanced Menu > Advanced Chipset Control)  You can adjust the Bluetooth module power setting to your preference. The default setting (Disabled) will see the Bluetooth module powered off when the system is SATA Mode started up or restarted.
Page 102: Boot Logo: (Advanced Menu)
BIOS Utilities Boot Logo: (Advanced Menu) Use this menu item to enable/disable the Boot Logo screen at system startup. Power On Boot Beep (Advanced Menu) Use this menu item to enable/disable the beep as the computer starts up. Battery Low Alarm Beep: (Advanced Menu) Use this menu item to enable/disable the battery low alarm beep.
Page 103: Security Menu
BIOS Utilities Security Menu  Security Menu The changes you make here affect the access to the Setup utility itself, and also access to your machine as it boots up after you turn it on. These settings do not affect your machine or network passwords which will be set in your...
Page 104 BIOS Utilities Note: To clear existing passwords press Enter and type the existing password, then  press Enter for the new password (without typing any password entry) and Enter again to confirm the password clearance. Password Warning If you set a boot pass- word (Password on boot is “Enabled“), NEVER forget your password.
Page 105: Boot Menu
BIOS Utilities Boot Menu Figure 5 - 5 Boot Menu  BIOS Screens Note that BIOS screens pictured these pages are intend- ed for guidance in set- ting up your system’s BIOS. BIOS versions are sub- ject to constant change and revision, therefore your computer’s actual When you turn the computer on it will look for an operating system (e.g.
Page 106: Boot Sequence (Boot Menu)
BIOS Utilities Boot Sequence (Boot Menu) Use the arrow keys to move up and down the menu and use the F5 and F6 keys to move the device’s boot priority up and down the list (the selected device will be highlighted in white).
Page 107: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 6 Exit Menu Click Save Changes and Exit to save all changes made. Choosing to Discard Changes, or Exit Discarding Changes, will wipe out any changes you have made to the Setup. You can also choose to restore the original Setup defaults that will re- turn the Setup to its original state, and erase any previous changes you have made in a previous session.
Page 108 BIOS Utilities 5 - 16...
Page 109: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview  This chapter contains information on upgrading the computer. Follow the steps out- Warranty Warning lined to make the desired upgrades. If you have any trouble or problems you can con- tact your service representative for further help.
Page 110: When Not To Upgrade
Upgrading The Computer When Not to Upgrade  These procedures involve opening the system’s case, adding and sometimes replac- ing parts.You should not perform any of these upgrades if: Power Safety Warning Before you undertake • Your system is still under warranty or a service contract upgrade proce- •...
Page 111: Removing The Battery
Upgrading The Computer Removing the Battery  If you are confident in undertaking upgrade procedures yourself, for safety reasons Warranty Warning it is best to remove the battery. Before removing the battery disconnect the AC/ DC adapter from the computer first. Note that only Model A/B is pictured, how- Please check with your ever the procedure for removing the battery from Model C is identical.
Page 112: Upgrading The Optical Device (Model A/B)
Upgrading The Computer Upgrading the Optical Device (Model A/B) Locate the hard disk bay cover and remove screws & Remove the hard disk bay cover Remove the screw at point , and use a screwdriver to carefully push out the optical device at point Reverse the process to install any new optical (CD/DVD) device.
Page 113: Upgrading The Optical Device (Model C)
Upgrading The Computer Upgrading the Optical Device (Model C) Locate the secondary hard disk bay cover and remove screws & Remove the hard disk bay cover Remove the screw at point , and use a screwdriver to carefully push out the optical device out of the bay.
Page 114: Upgrading The Hard Disk Drive(S)
Upgrading The Computer Upgrading the Hard Disk Drive(s)  The hard disk Drive(s) can be taken out to accommodate other 2.5" serial (SATA) HDD System Warning hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - 3).
Page 115 Upgrading The Computer Removing the Hard Disk from the Primary HDD Bay  Note that only Model A/B is pictured, however the procedure for removing the pri- mary hard disk from Model C is identical. RAID Hard Disks Turn the computer off, remove the AC/DC adapter, turn it over and remove the bat- All hard disks in a RAID tery.
Page 116 Upgrading The Computer Slide the HDD assembly in the direction of arrow Remove the hard disk assembly Figure 6 - 5 Hard Disk Assembly Removal 6 - 8 Upgrading the Hard Disk Drive(s)
Page 117 Upgrading The Computer Remove screws & and the insulation plate Reverse the process to install a new disk and do not forget to install the insulation plate. Figure 6 - 6 Hard Disk Insulation Plate Removal Upgrading the Hard Disk Drive(s) 6 - 9...
Page 118 Upgrading The Computer Inserting the Hard Disk Into the Primary HDD Bay Make sure the HDD assembly is aligned with the black taped area When aligned, carefully insert the HDD assembly into the case so that the connectors line up. Replace the hard disk bay covers and screws.
Page 119 Upgrading The Computer Removing the Hard Disk from the Secondary HDD Bay (Model C Only)  Note that the secondary hard disk (if installed) is located under the optical device bay (CD/DVD). RAID Hard Disks Turn the computer off, remove the AC/DC adapter, turn it over and remove the bat- All hard disks in a RAID tery.
Page 120 Upgrading The Computer Slide the secondary HDD assembly in the direction of the arrow (it will not move fully out of the bay), Lift the secondary HDD assembly up out of the bay (in the reverse direction to arrow Figure 6 - 9 Secondary HDD Assembly Removal 6 - 12 Upgrading the Hard Disk Drive(s)
Page 121 Upgrading The Computer Remove screws and the insulation plate Figure 6 - 10 Secondary Hard Disk Insulation Plate Removal Reverse the process to install a new disk (make sure you install the insulation plate). Slide the HDD assembly into the bay at an angle as illustrated. 10.
Page 122: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has four memory sockets for 204 pin Small Outline Dual In-line (SO- DIMM) DDR III (DDR3) type memory modules (see “Memory” on page C - The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 123: Replacing The Primary System Memory Modules
Upgrading The Computer Replacing the Primary System Memory Modules Turn off the computer, and turn it over and remove the battery. Remove screws from the bottom of the computer Figure 6 - 12 Bottom Cover Screws Models A & B Model C Slide the bottom cover until the cover and case indicators are aligned.
Page 124 Upgrading The Computer Lift the bottom cover off the computer case. Figure 6 - 14 Bottom Cover Removal  Contact Warning Be careful not to touch the metal pins on the module’s connecting Gently pull the two release latches ( &...
Page 125 Upgrading The Computer Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory socket. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the socket as it will go.
Page 126 Upgrading The Computer 6 - 18...
Page 127: Modules
Modules Chapter 7: Modules Overview This chapter contains the information on the various modules (some of which are optional) which may come with your computer, depending on the configuration purchased. If you are unsure please contact your service representative. The chapter includes information on the following: •...
Page 128: Setting Up Sata Raid Mode
Modules Setting Up SATA RAID Mode  AHCI Mode RAID Hard Disks Advanced Host Controller Interface (AHCI) is an interface specification that allows All hard disks in a RAID the storage driver to enable advanced serial ATA features such as Native Command should be identical (the same size and brand) in Queuing (for maximum hard disk efficiency and performance).
Page 129 Modules RAID Level Description Table 7 - 1 RAID Levels Identical drives reading and writing data in parallel to increase performance. RAID 0 RAID 0 implements a striped disk array and the data is broken into blocks and each block is written to a separate disk drive.
Page 130: Sata Raid Setup Procedure (Bios)
Modules SATA RAID Setup Procedure (BIOS) Start-up your notebook computer and press <F2> to enter the BIOS. Go to the Advanced menu, select "SATA Mode" and press Enter (see page • Select “RAID Mode”. Press Esc and go to the Boot menu. Set the DVD-ROM Drive (make sure the Microsoft Windows 7 OS DVD is inserted) as the first device in the boot order from the Boot menu (see “Boot...
Page 131: Raid Setup (Intel Matrix)
Modules RAID Setup (Intel Matrix) As the computer starts up press Ctrl + i to enter RAID configuration menu. Figure 7 - 1 Intel(R) Rapid Storage Technology Option ROM  Recovery Level When selecting disks for the Recovery RAID level you will need to use the Tab key to select a Mas- ter disk, and the Space...
Page 132 Modules Press Enter and the system will select the physical disks to use.  Press Enter and select (if applicable) the Strip Size (best set to default). Press Enter and select the Capacity size (best set to default). Recovery Level Press Enter to select Create Volume.
Page 133 Modules 12. Make sure the Windows 7 OS DVD is in the DVD drive. and as the computer  starts up it will automatically boot from the Windows 7 OS DVD (you will be prompted to press a key to boot from the DVD). Win7 (pre SP1) &...
Page 134: Intel Rapid Storage Technology
Modules Intel Rapid Storage Technology The Intel Rapid Storage Technology application provides high-performance SATA and SATA RAID capabilities. Install the Intel Rapid Storage Technology application to support your RAID system or SATA drive if set up in AHCI mode in the BIOS (see “SATA Mode (Advanced Menu)”...
Page 135 Modules Intel® Rapid Storage Technology for RAID Systems Intel® Rapid Storage Technology application displays status information on your RAID configuration. Run the Intel® Rapid Storage Technology application from the Intel item in the All Programs menu. When the Intel® Rapid Storage Technology application is launched the system will open the Status window.
Page 136 Modules Intel® Rapid Storage Technology Help  If a hard drive member of a RAID volume is reported as “Degraded” or “Failed” it may be possible to recover the volume. If the volume cannot be restored then you Help will need to recreate the RAID volume and restore the data from a back up. Click the Help menu (or press F1) for instructions on how to recover or recreate RAID Vol- Click the Help (or...
Page 137: Raid Volume Data Verification And Repair
Modules RAID Volume Data Verification and Repair The RAID volume data verification process identifies any inconsistencies or bad data on a RAID 0 or RAID 1 volume. The table outlines what occurs for each RAID level: RAID Verify Verify & Repair Level Table 7 - 2 RAID 0...
Page 138 Modules Verifying and Repairing RAID Volume Data Before verifying the volume data you will need to initialize the volume. Run the Intel® Rapid Storage Technology application from the Intel item in the Programs/All Programs menu. Click Manage and click Advanced. Click Initialize and click Yes (button) to begin the process.
Page 139 Modules Click Advanced and click Verify, then click Verify (button) to begin the process. The completion percentage will be listed under Status (verifying and repairing). Figure 7 - 6 ® Intel Rapid Storage Technology Verify Intel Rapid Storage Technology 7 - 13...
Page 140: Pc Camera Module
Modules PC Camera Module  Before installing the driver, make sure the PC Camera is on. Use the Fn + F10 key Latest PC Camera combination to toggle power to the to the PC Camera module. When the PC Camera Driver Information module is powered on the indicator will briefly be displayed.
Page 141: Pc Camera Driver Installation
Modules PC Camera Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers (button). 3. Click 1.Install Webcam Driver > Yes. 4. Click Next > Install > Finish to restart the computer. Choose the language you prefer and click Next >...
Page 142: Pc Camera Audio Setup
Modules PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 143 Modules Figure 7 - 7 Audio Setup for PC Camera Right-click PC Camera Module 7 - 17...
Page 144 Modules Camera Application The camera application is a video viewer for general purpose video viewing and test- ing, and for capturing video files to .avi format. Run the camera application from the desktop shortcut (it is recommended that you set the capture file before the capture process - see below). Go to the Capture menu heading (if you wish to capture audio check “PC Camera Audio Setup”...
Page 145 Modules Reducing Video File Size Note that capturing high resolution video files requires a substantial amount of disk space for each file. After recording video, check the video file size (right-click the file and select Properties) and the remaining free space on your hard disk (go to My Computer, right-click the hard disk, and select Properties).
Page 146 Modules Eliminating Screen Flicker  If you find that the video screen in the camera program is flickering, you can try to adjust the setting in the Video Capture Filter options. Latest PC Camera Driver Information Run the camera application from the desktop shortcut. Go to Options and scroll down to select Video Capture Filter..
Page 147 Modules Taking Still Pictures  The camera application allows you to take still pictures. Snapshot Folder Run the camera application from the desktop shortcut. Go to Options and select Take Picture. The Snapshot folder’s The picture (in JPEG format) will be placed in the Snapshot folder on the default location is on the desktop.
Page 148: Wireless Lan Module
Modules Wireless LAN Module  If you have included an Intel® or 3rd Party 802.11b/g/n WLAN module in your Wireless Device purchase option, make sure that the Wireless LAN module is on before installing the Operation Aboard driver. Aircraft The use of any portable Use the Fn + F11 key combination to toggle power to the Wireless LAN module.
Page 149: Intel® Wi-Fi Link Series Driver Installation
Modules Intel® Wi-Fi Link Series Driver Installation  If you see the message “Found New Hardware” click Cancel to close the window. Intel(R) PROSet/ 1. Make sure the module is powered on, then insert the Device Drivers & Util- Wireless ities + User’s Manual disc into the CD/DVD drive.
Page 150: Connecting To A Wireless Network In Windows 7
Modules Connecting to a Wireless Network in Windows 7  Make sure the Wireless LAN module is turned on. Network and Click the taskbar wireless icon , and then double-click an access point to con- Sharing Center nect to or click to Open Network and Sharing Center if you do not see a network you want to connect to in the taskbar menu (a list of options will appear allowing You can also use the Net- setting changes, and creating a new network).
Page 151 Modules You may need to enter a security key for any access point to which you are trying to connect. Click to select a network location (e.g. Home, Work or Public). Click “View or change settings in Network and Sharing Center” to access further options for the connection.
Page 152 Modules Click the taskbar icon to see any currently connected networks.  To disconnect from the wireless network you can click the taskbar wireless icon click the active connection and then click Disconnect (button). Security Enabled Networks You should try to make sure that any network you are connecting to is a se- cure network.
Page 153: Intel My Wifi Configuration
Modules Intel My WiFi Configuration ®  Intel® My WiFi Technology uses your WLAN (for Intel WLAN modules only) module to allow you to connect up to eight other WiFi enabled devices (e.g. digital Intel® My WiFi Help cameras, other computers, cell phones, handheld devices etc.) to your computer To get help on Intel®...
Page 154 Modules Intel® My WiFi Configuration You can configure the My WiFi settings as follows. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by double- clicking the taskbar icon Click Enable (on the first run of the program there will be no connected...
Page 155 Modules Click Start and click Control Panel. Click Network and Sharing Center (Network and Internet). Click Change adapter settings. Figure 7 - 13 Network and Sharing Center Click Change adapter settings Wireless LAN Module 7 - 29...
Page 156 Modules Right-click Wireless Network Connection and select Properties. Figure 7 - 14 Network Connections Right-click Wireless Network Connection and select Proper- ties. 7 - 30 Wireless LAN Module...
Page 157 Modules Click Sharing (tab) and select “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Connection under Home networking connection. Click OK. Click “Allow other network users to connect through this computer’s Internet connection”. Select Wireless Network Figure 7 - 15 Connection.
Page 158 Modules 10. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by double- clicking the taskbar icon 11. Click Profiles Figure 7 - 16 Intel® My WiFi Utility - Profiles 7 - 32 Wireless LAN Module...
Page 159 Modules 12. Click Profiles, click Intel Wireless PAN and click Edit or New (Note that all preset settings may not be editable - see sidebar). Figure 7 - 17 Profiles  Profile Settings Profiles that are preset may not be fully edit- 13.
Page 160 Modules 14. Click Security (tab). 15. Change the Security Type to WEP and the Encryption Type to 64bit. 16. Enter a password (8 characters long) in the Password box. Figure 7 - 19 Intel® My WiFi Profile Settings - Security 7 - 34 Wireless LAN Module...
Page 161 Modules 17. Click Sharing (tab). 18. It is recommended that the Filter Network Traffic and DHCP and DNS Server are Disabled. Figure 7 - 20 Intel® My WiFi Profile Settings - Sharing Wireless LAN Module 7 - 35...
Page 162 Modules 19. Click Advanced (tab). 20. It is recommended that the Default Channel is set to Channel 1, 6 or 11. 21. Click OK to save the settings. Figure 7 - 21 Intel® My WiFi Profile Settings - Advanced 7 - 36 Wireless LAN Module...
Page 163 Modules 22. Double-click Wireless Network Connection in Network Connections. 23. Click Details to display the Network Connection Details. Figure 7 - 22 Wireless Network Connection Details Wireless LAN Module 7 - 37...
Page 164 Modules 24. Access the Intel® My WiFi Utility from the Start menu (Start > Programs/All Programs > Intel PROSet Wireless > Intel My WiFi Technology), or by clicking the taskbar icon 25. To add a new device follow the instructions in the devices’ user guide for connecting to a WiFi network.
Page 165: Data Transfer Configuration
Modules Intel WLAN Module High-Speed Data Transfer Configuration You will need to configure the following settings to enable high-speed wireless data transfer as supported by Intel Wireless LAN modules (note this information applies to Intel WLAN modules only). Go the Windows control panel and double-click Device Manager (in Hardware and Sound under Devices and Printers).
Page 166 Modules Click Network adapters to expand the sub-menu. Double-click the Intel WiFi Link ..module. Click Advanced (tab). Click 802.11n Channel Width for band 2.4 under “Property:”. Click the pull-down menu under “Value:” Click to select Auto. Click OK and close the control panels. Figure 7 - 25 Intel WiFi Link Properties...
Page 167: Windows Mobility Center
Modules Windows Mobility Center  The Windows Mobility Center control panel provides an easy point of access for information on battery status, power plans used and wireless device status etc. Wireless Hot Keys To access the Windows Mobility Center: The computer’s wireless function keys will not func- Click Start, and click Control Panel (or point to Settings and click Control tion properly if Wireless is...
Page 168: Fingerprint Reader Module
Modules Fingerprint Reader Module  The fingerprint reader Protector Suite Software provides a high level of security Password Warning for your computer. A further level of security and control is provided in the BIOS (see “Security Menu” on page 5 - 11).
Page 169: Fingerprint Reader Driver Installation
Modules Fingerprint Reader Driver Installation 1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. 2. Click Option Drivers. 3. Click 3.Install FingerPrint Driver > Yes. 4. Click Next > Next > Next. 5. Click Finish > Yes to restart the computer. 6.
Page 170: User Enrollment
Modules User Enrollment  Click Start > Programs/All Programs > Protector Suite > Control Center, or double click the taskbar icon (click Initialize). Fingerprint On the first run of the program you will be asked to click the Accept button to Enrollment accept the license.
Page 171 Modules Click the button above any of the fingers to begin the enrollment process for that finger.  Swipe the finger until the progress bar reaches 100% to enroll that finger. Fingerprint Enrollment Note that it is strongly rec- ommended that you enroll more than one finger in case of injury etc.
Page 172 Modules Right-click the taskbar icon and select Start Control Center (and then swipe a finger) to allow you to Edit Fingerprints, register Applications, edit Settings and access the Help menu etc. You can also run the Control Center etc. from the Protector Suite item in the Programs/All Programs menu 10.
Page 173: Fingerprint Control Center Features
Modules Fingerprint Control Center Features  Application Launcher Help The Application Launcher allows you to register applications to be launched when assigned to a particular finger. Simply copy the application icon on to one of the reg- For more information on istered fingers and ten click OK to close the application window.
Page 174: Bluetooth Module
Modules Bluetooth Module  If your purchase option includes the Combination Wireless LAN & V3.0 Blue- Wireless Device tooth module (either Intel or 3rd Party) then install the driver as instructed over- Operation Aboard leaf. Follow the instructions on page 7 - 54 to configure the Bluetooth settings.
Page 175: 3Rd Party Bluetooth Combo Driver Installation
Modules 3rd Party Bluetooth Combo Driver Installation  Note this driver is required only for the combo Bluetooth and WLAN module only. High Speed Bluetooth 1. Before installing the driver make sure the Bluetooth module is powered Data Transfer on (use Fn + F12 key combination), then insert the Device Drivers & Utili- The Combination Wire- ties + User’s Manual disc into the CD/DVD drive.
Page 176: 3Rd Party Bluetooth & Wlan Combo Settings
Modules 3rd Party Bluetooth & WLAN Combo Settings  This information applies to the combo Bluetooth and WLAN module only. Bluetooth Module & Make sure the Bluetooth module is powered on. Resuming From Sleep Double-click the My Bluetooth application on the desktop (or access it from the Mode Programs/All Programs menu).
Page 177 Modules Click General Settings to change the computer name that other Bluetooth devices will see, and click the tickbox to Allow Bluetooth devices to find this computer Click OK to confirm the settings. Figure 7 - 31 General Settings Bluetooth Module 7 - 51...
Page 178 Modules Click File Transfer Settings to Enable sharing of my files with other Bluetooth devices. Click OK to confirm the settings. Figure 7 - 32 File Transfer Settings 7 - 52 Bluetooth Module...
Page 179: 3Rd Party Bluetooth Networking Setup
Modules 3rd Party Bluetooth Networking Setup This information applies to the combo Bluetooth and WLAN module only. Make sure the Bluetooth module is powered on. Double-click the My Bluetooth application on the desktop (or access it from the Programs/All Programs menu). Click My Bluetooth Settings (see Figure 7 - 30 on page 7 - 50).
Page 180: 3Rd Party Bluetooth & Wlan Combo Module Configuration
Modules 3rd Party Bluetooth & WLAN Combo Module Configuration  Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Bluetooth Module & Make the device discoverable (to do this check your device documentation). Resuming From Sleep Mode To Turn the Bluetooth Module On...
Page 181 Modules You will then be presented with a menu of options to select from. Figure 7 - 35 Bluetooth Device Options Click the appropriate button to connect to the device. Bluetooth Module 7 - 55...
Page 182 Modules You may need to allow the connection from your device, and you will then need to provide a passcode from the device. You can then enter the passcode on the computer and click OK to establish the connection. Figure 7 - 36 Bluetooth Pairing Code &...
Page 183: Intel Bluetooth Combo Driver Installation
Modules Intel Bluetooth Combo Driver Installation  Note this driver is required only for the Intel combo Bluetooth and WLAN module only. High Speed Bluetooth Data Transfer 1. Before installing the driver make sure the Bluetooth module is powered The Combination Wire- on (use Fn + F12 key combination), then insert the Device Drivers &...
Page 184: Standard Bluetooth Configuration In Windows 7
Modules Standard Bluetooth Configuration in Windows 7  Setup your Bluetooth Device so the Computer Can Find it Turn your Bluetooth device (e.g. PDA, mobile phone etc.) on. Add a Device Make the device discoverable (to do this check your device documentation). Click Start, and click Con- trol Panel and then click To Turn the Bluetooth Module On...
Page 185 Modules To Add a Bluetooth Device  Access the Bluetooth Devices control panel and click Add a device. Double-click the device you want to pair with the computer. Pairing Options If a device has been pre- viously connected then the pairing option menu will appear when you at- tempt subsequent con- nections.
Page 186 Modules Enter the code into your Bluetooth enabled device and follow any on-screen instructions to complete the pairing.  Figure 7 - 39 Pairing Codes Pairing Code Example The example outlined here shows a connection to a mobile device. Other devices e.g. computers, may have a slightly different connection proce- dure, and may require you to confirm a pairing code is correct on both devices.
Page 187 Modules To Change Settings for the Bluetooth Device  Click the taskbar icon and select Show Bluetooth Devices. Right-click on the device you want to change and click Properties to: Bluetooth Help • Change the name of the device (click Bluetooth, type a new name and click OK). •...
Page 188: 3.75G/Hspa Module
Modules 3.75G/HSPA Module (Models A & B Only) If you have included an optional 3.75G/HSPA (High Speed Packet Access) module (see “Communication” on page D - 6 for specification details) in your purchase op- tion, you will have the appropriate application (BandLuxe HSDPA Utility) provid- ed for your module.
Page 189: 3.75G/Hspa Module Usim Card Installation
Modules 3.75G/HSPA Module USIM Card Installation  Follow the instructions below to install the USIM card (which will be provided by Power Safety your service provider). Warning Turn the computer off, remove the AC/DC adapter and turn it over. Before you undertake any Slide the latch in the direction of the arrow.
Page 190 Modules Remove the battery. Insert the USIM card as illustrated below until it clicks fully into position, and replace the battery. Figure 7 - 43 USIM Card Insertion 7 - 64 3.75G/HSPA Module...
Page 191 Modules Before installing the application, make sure that the 3.75G/HSPA module is ON  (installing the driver with the module off will not allow the software to detect the module hardware correctly). Use the Fn + key combination (see “Function/Hot 3.75G/HSPA Key Indicators”...
Page 192: Bandluxe Hsdpa Utility
Modules BandLuxe HSDPA Utility  With the 3.75G/HSPA module and USIM card (supplied by your service provider) installed you may then install the BandLuxe HSDPA Utility. The BandLuxe HS- Wireless Device DPA Utility allows you to directly access your HSPA internet service from the com- Operation Aboard Aircraft puter.
Page 193: Bandluxe Hsdpa - Connection Manager
Modules BandLuxe HSDPA - Connection Manager The connection information is stored on the USIM card supplied by the service pro- vider (where this is not the case you may need to create a profile - see “Creating a Profile” on page 7 - 70).
Page 194 Modules The system will connect to your network (you may need to set your network connection to home, work or public on the first connection). The connected icon will appear at the top of the utility screen. Figure 7 - 45 Connected You can then access the internet, download e-mail etc.
Page 195 Modules While you are connected the taskbar icon will display the connected icon , and the taskbar will display the connected icon Figure 7 - 47 Taskbar Icon (Connected) To disconnect from the service provider, click the Disconnect icon, or click the close icon at the top right of the utility, and click Yes to confirm.
Page 196: Creating A Profile
Modules Creating a Profile Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu > Profile. Figure 7 - 48 Menu - Profile The default profile will display the service provider’s name from the USIM card.
Page 197 Modules Click New (button) and input any Network Settings required by your service  provider (all fields may not need to be filled in). The profile name is used to identify your profile if a number of profiles are used. You will need to check with your service provider to confirm if the User Name and Password Password are required.
Page 198 Modules Click the newly created profile in the profile window and then click Default (button)  to set the profile as the default connection (note that only one profile may be stored as the default connection). New SIM Card 10. The newly created profile will now be stored as the default connection when you click Connect in the Connection Manager Home screen.
Page 199: Choosing A Profile
Modules Choosing a Profile If you need to switch stored profiles follow the instructions below: Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 > Connection Manager). Click the Menu >...
Page 200: Editing A Profile
Modules Editing a Profile  If you need to edit stored profiles follow the instructions below: Get the Latest Access the Connection Manager from the Start menu (Connection Manager Access Point Name ), or (Start > Programs/All Programs > BandLuxe > BandLuxe Database HSDPA Utility R11 >...
Page 201: Text Messaging Service (Sms)
Modules Text Messaging Service (SMS)  In addition to standard internet services you may also send and receive SMS text messages using the Connection Manager, if your service supports SMS. Incoming Messages Inbox If the program is open The Inbox will contain any received SMS. Click to select the message and it will (you do not have to be connected) you will be scroll open above.
Page 202 Modules Sent  The Sent folder contains any successfully sent SMS. Select the message and press the Delete to erase the record. Contact List Types Outbox Select a contact The Outbox folder contains any completed but unsent SMS. Select the message and from the SIM card.
Page 203 Modules Template A template can store text that is used regularly in messages, and can be easily insert- ed in to any new SMS. Click Template (button) to view any stored templates. Click to highlight a template and click Select (button) to insert it into the message. Click New (button) to create a new template, and Save (button) to add it to the existing list.
Page 204: Setting
Modules Setting  The Setting menu allows you to edit the programs basic parameters. Access the Connection Manager from the Start menu (Connection Manager Language ), or (Start > Programs/All Programs > BandLuxe > BandLuxe The Connection Manager HSDPA Utility R11 > Connection Manager). offers multiple language Click the Menu >...
Page 205 Modules SMS - Preference Click the New SMS Notify checkbox to be automatically notified when a new SMS arrives. If enabled a the incoming message notification will appear in the taskbar, Figure 7 - 58 Incoming SMS Notification and an envelope icon will appear in the upper left corner of the Home screen when a new message arrives.
Page 206 Modules This menu allows you to edit the USIM card Personal Identification Number (PIN) and Enable/Disable the PIN if necessary. Press Apply after making any changes. A SIM card must be inserted for this function to be activated. Figure 7 - 60 Setting - SIM If a PIN code is enabled, the input will be requested during USIM card initialization.
Page 207 Modules Radio Set the appropriate network search options from the dual mode setting menu. Click Apply (button) after making any changes. Figure 7 - 61 Setting - Radio Note: 2G/3G/3.5G data transferring will be disconnected when you apply a new Ra- dio setting.
Page 208 Modules Network - Network Selection  Edit the network selection settings from this menu. The Standard (auto) setting will search for networks in the order specified in the Prefer list. Click Standard (auto) Network Setting > Next to view and adjust the Prefer list. The Prefer list is displayed at the top of the Note that the network set- screen, and the bottom of the screen lists all available networks.
Page 209 Modules The Manual setting allows you to choose a network from all available. Click Man- ual > Next to view the list. Click to highlight a network from the list, and click Se- lect (button) to choose the network, or Cancel (button) to make no change. Figure 7 - 63 Setting - Network Manual...
Page 210: Statistics & Information
Modules Statistics & Information The Statistics screen displays a graph of recent upload and download activity. No data will be displayed if there is no current connection. Access the Connection Manager from the Start menu (Connection Manager ), or (Start > Programs/All Programs > BandLuxe > BandLuxe HSDPA Utility R11 >...
Page 211: Tv Tuner Module
Modules TV Tuner Module  (Model C Only) TV Antenna If your purchase configuration includes the optional USB Mini-Card TV Tuner The TV antenna sup- module, you will be supplied with a remote control unit and appropriate fittings for plied with any TV Tuner the module.
Page 212: Consumer Infrared Driver
Modules Consumer Infrared Driver  1. Insert the Device Drivers & Utilities + User’s Manual disc into the CD/ DVD drive. TV Tuner Module Support 2. Click Option Drivers (button). 3. Click 5.Install CIR Driver > Yes. Note that the TV Tuner 4.
Page 213: Digital Tv Broadcast Signal
Modules Digital TV Broadcast Signal  The antenna is the most crucial factor in receiving a clear digital terrestrial TV broadcast signal. The passive antenna provided should provide a clear signal when CATV Cable Safety placed beside a window. If the signal is not clear then you can purchase an active Make sure that your antenna (it should also be placed beside a window) to improve the signal.
Page 214: Thx Trustudio Pro Audio
Modules THX TruStudio Pro Audio  Install the THX TruStudio AP to allow you to configure the audio settings to your THX TruStudio & requirements for the best performance in games, music and movies. Speaker Configuration THX TruStudio AP Installation Note that THX TruStu- 1.
Page 215: Thx Trustudio Pro Activation
Modules THX TruStudio Pro Activation  On the first run of THX TruStudio Pro you will need to activate the application. THX Audio & HDMI To activate the application you will need to be connected to the internet. Double-click the THX Activate icon on the desktop and click the Activate Note that the THX audio effects do not apply to...
Page 216 Modules THX Control Panel Each control has an On/Off button to allow you to enable/disable the control, and most controls feature a slider to adjust the levels (the subwoofer may be turned on/ off). Figure 7 - 67 Menu THX TruStudio Pro Controls •...
Page 217 Modules THX TruStudio Pro & HDMI When you connect an HDMI display to the HDMI-Out port,the THX Tru Studio Pro controls will be disabled. A warning box will pop-up and will prompt “Do you want to select another audio device now?”. Click No to continue using the HDMI audio output from your external display (do not attempt to select another audio device when connected to the external HDMI display).
Page 218 Modules 7 - 92...
Page 219: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 220: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer ap- pears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 221: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wal- let.
Page 222: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the defini- tions file updates are usually downloadable directly from the internet.
Page 223: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 224 Troubleshooting • Don’t over complicate things. The less you have to deal with then the easier the source of the problem may be found; Example - if your computer has many devices plugged into its ports, and a number of programs running, then it will be difficult to determine the cause of a problem.
Page 225: Problems & Possible Solutions
Troubleshooting Problems & Possible Solutions Problem Possible Cause - Solution You turned the power on Battery missing / incorrectly installed. Check the battery bay, make sure the battery is present and but it doesn’t work. seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
Page 226 Troubleshooting Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the vents/fan intakes are not blocked. If this hot. doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 227 Troubleshooting Problem Possible Cause - Solution forget boot If you forget the password, you may have to discharge the battery of the CMOS. Contact your password. service representative for help.  Password Warning If you choose to set a boot password, NEVER forget your password. The consequences of this could be serious. If you cannot remember your boot password you must contact your vendor and you may lose all of the information on your hard disk.
Page 228 Troubleshooting Problem Possible Cause - Solution The TouchPad doesn’t The Touchpad has been disabled. Press the Touchpad toggle (Fn + F1) key combination (make work. sure you have installed the Touchpad driver. The system freezes or The system’s power saving features have timed-out. Use the AC/DC adapter, press a key on the the screen goes dark.
Page 229 Troubleshooting Problem Possible Cause - Solution When a DVD is played in This is an issue with Windows Media Player/Media Center and audio output through the S/PDIF- Windows Media Player/ Out Jack. We recommend that you use the Power DVD application to play DVDs. Media Center, the audio track in other languages (commentaries etc.) is...
Page 230 Troubleshooting Problem Possible Cause - Solution Wireless The WLAN module is turned off in the Windows Mobility Center. The computer’s wireless indicators function keys will not function properly if Wireless is turned OFF in the Windows Mobility show that the WLAN Center control panel.
Page 231: Bluetooth Connection Problems
Troubleshooting Bluetooth Connection Problems If you are experiencing problems connecting to some Bluetooth devices (in particular certain mobile phones and headsets) it maybe necessary to download and install the Windows Mobile Device Center software (for Win- dows Vista and Windows 7). Go to the Microsoft website and search for the Microsoft Windows Device Center Driver for Windows Vista (64-bit or 32-bit) and Windows 7 (64-bit or 32-bit), and then download the driver.
Page 232 Troubleshooting Right-click Bluetooth Peripheral Device and click on Update Driver Software. Click Browse my computer for driver software. Click Let Me pick from a list of device drivers on my computer. Figure 8 - 2 - Browse my computer.../Let me pick from... Select Bluetooth Radios from the list.
Page 233 Troubleshooting 10. A list of drivers will appear with Manufacturer on one side and Model in the other. 11. Choose Microsoft Corporation (make sure you choose the full name Microsoft Corporation and do not choose Microsoft - Note that you must have installed the Microsoft Windows Device Center Driver for Microsoft Corporation to appear in the list).
Page 234 Troubleshooting 15. The Device Manager should now display the Windows Mobile-based device support under Bluetooth Radios. 16. You will need to repeat the process for any other Bluetooth Peripheral Devices listed under Other Devices. Figure 8 - 5 - Device Manager - Bluetooth Radio 8 - 16 Bluetooth Connection Problems...
Page 235: Intel® Centrino Advanced 6230 Wlan & Bluetooth V3.0+Hs Combo Modules
Troubleshooting Intel® Centrino Advanced 6230 WLAN & Bluetooth V3.0+HS Combo Modules Note that, at the time of going to press, Intel® Centrino Advanced 6230 WLAN & Bluetooth V3.0+HS combo modules use the standard Bluetooth configuration in Windows 7 (see “Intel Bluetooth Combo Driver Installa- tion”...
Page 236: Installing Windows 7 (Pre Service Pack 1) For Raid Systems With Advanced Format Disks
Troubleshooting Installing Windows 7 (pre Service Pack 1) for RAID Systems with Advanced Format Disks The following information is only applicable under the following conditions: • You are configuring your SATA hard disks in a RAID. • You are using Advanced Format hard disks that have a 4KB physical sector size. •...
Page 237 Troubleshooting Press a key at system startup to begin installing Windows from your Microsoft Windows 7 disc (make sure the DVD device is set at the top of the Boot Sequence in the BIOS - see “Boot Sequence (Boot Menu)” on page 5 - 14).
Page 238 Troubleshooting 8 - 20...
Page 239: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the ports & jacks which allow your computer to commu- nicate with external devices, connect to the internet etc. Interface (Ports & Jacks) A - 1...
Page 240: Ports And Jacks
Interface (Ports & Jacks) Ports and Jacks Item Description Card Reader The card reader allows you to use the following digital storage cards: MMC (MultiMedia Card) / RSMMC SD (Secure Digital) / Mini SD / SDHC / SDXC Compatible MS (Memory Stick) / MS Pro / MS Duo Push the card into the slot and it will appear as a removable device.
Page 241: Hdmi-Out Port
Interface (Ports & Jacks) Item Description e-SATA / USB 2.0 This e-SATA (external Serial Advanced Technology Attachment) port allows you to plug-in Combo Port external Serial ATA hard drives. This port also serves as a USB 2.0 port. /e-SATA / HDMI-Out Port The HDMI-Out (High-Definition Multimedia Interface) port is an audio/video connector interface for transmitting uncompressed digital streams.
Page 242: Mini-Ieee 1394A Port
Interface (Ports & Jacks) Item Description Mini-IEEE 1394a Port This allows high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below).  IEEE 1394a The Mini-IEEE 1394 ports only support SELF POWERED IEEE 1394 devices. RJ-45 LAN Jack This port supports LAN (Network) functions.
Page 243: Usb 2.0/1.1 Ports
Interface (Ports & Jacks) Item Description USB 2.0/1.1 Ports These USB (Universal Serial Bus) 2.0 compatible ports (USB 2.0 is fully USB 1.1 compliant) are for low-speed peripherals such as keyboards, mice or scanners, and for high-speed peripherals such as external HDDs, digital video cameras or high-speed scanners etc. Devices can be USB 3.0 Port plugged into the computer, and unplugged from the computer, without the need to turn the system off (if the power rating of your USB device is 500mA or above, make sure you use the power...
Page 244 Interface (Ports & Jacks) A - 6...
Page 245: Nvidia Video Driver Controls
NVIDIA Video Driver Controls Appendix B: NVIDIA Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on  page 1 - NVIDIA Video Driver Installation Video Card Options Note that card types, Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - specifications and driv- 1.
Page 246: Nvidia Control Panel (Win 7
NVIDIA Video Driver Controls NVIDIA Control Panel (Win 7)  More advanced video configuration options are provided in the NVIDIA Control NVIDIA Control Panel tab. Panel Click Start, and click Control Panel (or point to Settings and click Control Panel). To access the Ge- Double-click NVIDIA Control Panel (click "Classic View"...
Page 247 NVIDIA Video Driver Controls The NVIDIA Control Panel provides additional video configuration controls and  tools which allow quick access to features such as display configuration, 3D Settings and Help menus etc. Navigating the Control Panel Navigate through the control panels in much the same way as you would a web page.
Page 248 NVIDIA Video Driver Controls The Help menus provide index and search features, and direct links to the NVIDIA website etc. Figure B - 3 Help Menu B - 4 NVIDIA Control Panel (Win 7)
Page 249: Display Devices
NVIDIA Video Driver Controls Display Devices  Note that you can use a DVI cable connected to the DVI-Out port, or an HDMI Display Devices (High-Definition Multimedia Interface) cable connected to the HDMI-Out port to connect an external display (if you are using an older type of monitor you can use a Besides the built-in LCD, you can also use an exter- converter to convert the signal from DVI to VGA).
Page 250: Display Modes
NVIDIA Video Driver Controls Display Modes Single Display Mode Only one of your displays is used. Duplicate Displays Duplicate simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same content. Extend Desktop Extend Desktop treats both connected displays as separate devices, and they act as a virtual desktop resulting in a large workspace.
Page 251 NVIDIA Video Driver Controls Configuring an External Display using the NVIDIA Control Panel  You can use the NVIDIA control panel to configure any attached displays. Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Display Not Shown Go to NVIDIA Control Panel (see page If the attached display...
Page 252 NVIDIA Video Driver Controls Duplicating the Displays Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page Double-click Display (if the sub-menus are not visible), and then click Set up multiple displays.
Page 253 NVIDIA Video Driver Controls Extending the Display  Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Go to NVIDIA Control Panel (see page Changing the Double-click Display (if the sub-menus are not visible), and then click Set up Primary Display on multiple displays.
Page 254: Attaching Other Displays (Win 7
NVIDIA Video Driver Controls Attaching Other Displays (Win 7)  Configuring an External Display in Windows 7 Function Key Attach your external display to the DVI-Out Port or HDMI-Out port, and turn it on. Combination Go to the Screen resolution control panel. Click the Detect button.
Page 255 NVIDIA Video Driver Controls You can configure the displays from the Multiple Displays menu. Figure B - 8 Screen Resolution Multiple Display Options (Win 7) • Duplicate these displays - Shows an exact copy of the main display desktop on the other display(s) •...
Page 256 NVIDIA Video Driver Controls Using the Windows Logo Key + P Key Combination to Switch Displays You can also use the + P key combination to quickly change display configura- tion and modes (this is particularly useful when attaching a projector) in Windows 7. Attach your external display to the external monitor port and turn it on.
Page 257: Hdmi Audio Configuration
NVIDIA Video Driver Controls HDMI Audio Configuration As HDMI (High-Definition Multimedia Interface) carries both audio and video sig- nals you can configure the audio output from the NVIDIA control panel and Sound control panel. The settings will depend upon the external HDMI display you have connected to.
Page 258 NVIDIA Video Driver Controls Windows Audio Setup for HDMI In some cases it will be necessary to go to the Sound control panel and manually con- figure the HDMI audio output. Click Start, and click Control Panel (or point to Settings and click Control Panel). Click Sound (Hardware and Sound).
Page 259 NVIDIA Video Driver Controls Adjust the HDMI settings from the control panel tabs. Click OK to close the Sound control panel. Figure B - 12 HDMI Device Properties Attaching Other Displays (Win 7) B - 15...
Page 260 NVIDIA Video Driver Controls HDMI Notes  • Connect a device with HDMI support to the HDMI-Out port BEFORE attempt- ing to play audio/video sources through the device. Other Applications • Under certain conditions, if the HDMI cable is disconnected, the default audio If you are using a third playback device will not revert to speakers until the computer is restarted (if you party application to play...
Page 261 NVIDIA Video Driver Controls HDCP Status If your external display is HDCP (High Bandwith Digital Content protection) com- patible then the NVIDIA control panel will display the HDCP system status. Figure B - 13 HDCP Status Attaching Other Displays (Win 7) B - 17...
Page 262 NVIDIA Video Driver Controls B - 18...
Page 263: Specifications
Specifications Appendix C: Specifications  Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly processor types/ speeds and CD/DVD device types) may be changed, updated or delayed due to the manufacturer's release schedule. Check with your service center for details.
Page 264: Processor
Specifications Processor Processor Processor Note all processor packages are Models A, B & C: Model C Only: rPGA988B Intel® Core i7-2820QM (2.3GHz) Intel® Core i7-2620M (2.7GHz) Quad-Core Mobile Processor Mobile Processor Models A& C Only: 8M L3 Cache, 32nm (32 Nanometer), 4M L3 Cache, 32nm (32 Nanometer), Intel®...
Page 265: Memory
Specifications Memory Display Video Adapter Options Dual Channel DDRIII (DDR3) Model A: Models A & C: 15.6" (39.62cm) FHD (1920 * 1080) 16:9 nVIDIA® GeForce GTX 485M PCIe * 16 *Four 204 Pin SO-DIMM Sockets Panel Video Card Supporting DDRIII (DDR3) 1066MHz/ Model B: 2GB GDDR5 Video RAM On Board 1333/1600** MHz Memory Modules...
Page 266: Storage
Specifications Storage Keyboard & Pointing Device Interface One 12.7 mm Super Multi/Blu-Ray Full Size Winkey Keyboard with Numeric Model C: Combo/Blu-Ray Writer SATA Optical Keypad with WASD Gaming Marking One CATV Input Jack for TV Antenna (for Device Drive (Factory Option) Built-In TouchPad (with Multi Gesture TV Tuner Mini-Card) Functionality)
Page 267: Card Reader
Specifications Card Reader Communication Power Management Embedded Multi-In-1 Card Reader 2.0M Pixel PC Video Camera Module Supports Wake on LAN (Factory Option) - MMC / RSMMC Supports Wake on USB - SD / Mini SD / SDHC / Energy Star 5.0 Models A &...
Page 268 Specifications Environmental Spec Temperature ° ° Operating: C - 35 Non-Operating: -20°C - 60°C Relative Humidity Operating: 20% - 80% Non-Operating: 10% - 90% Physical Dimensions & Weight Models A & B: 376mm (w) * 256mm (d) * 35 - 43mm (h) 3.1kg with ODD and Battery Model C: 412mm (w) * 276mm (d) * 45.4 - 41.8mm...

EUROCOM Notebook User Manual

Quick Start Guide

Storage Devices, Mouse, Audio & Printer

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules

Troubleshooting

Interface (Ports & Jacks)

NVIDIA Video Driver Controls

Specifications

Quick Links

Need help?

Questions and answers

Related Manuals for EUROCOM Notebook

Summary of Contents for EUROCOM Notebook