Page 3 Preface Notice The company reserves the right to revise this publication or to change its contents without notice. Infor- mation contained herein is for reference only and does not constitute a commitment on the part of the man- ufacturer or any subsequent vendor. They assume no responsibility or liability for any errors or inaccuracies that may appear in this publication nor are they in anyway responsible for any loss or damage resulting from the use (or misuse) of this publication.
Page 4: Fcc Statement
Preface FCC Statement (Federal Communications Commission) This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Page 5: Important Safety Instructions
Preface IMPORTANT SAFETY INSTRUCTIONS Follow basic safety precautions, including those listed below, to reduce the risk of fire, electric shock, and injury to persons when using any electrical equipment: Do not use this product near water, for example near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool.
Page 6: Instructions For Care And Operation
Preface Instructions for Care and Operation The notebook computer is quite rugged, but it can be damaged. To prevent this, follow these suggestions: Don’t drop it, or expose it to shock. If the computer falls, the case and the components could be dam- aged.
Page 7 Preface Avoid interference. Keep the computer away from high capacity transformers, electric motors, and other strong magnetic fields. These can hinder proper performance and damage your data. Follow the proper working procedures for the computer. Shut the computer down properly and don’t forget to save your work.
Page 8: Power Safety
Preface Power Safety The computer has specific power requirements: • Only use a power adapter approved for use with this computer. • Your AC/DC adapter may be designed for international travel but it still requires a Power Safety steady, uninterrupted power supply. If you are unsure of your local power specifi- Warning cations, consult your service representative or local power company.
Page 9: Battery Precautions
Preface Battery Precautions • Only use batteries designed for this computer. The wrong battery type may explode, leak or damage the com- puter. • Do not remove any batteries from the computer while it is powered on. • Do not continue to use a battery that has been dropped, or that appears damaged (e.g. bent or twisted) in any way.
Page 10: Cleaning
Preface Cleaning Do not apply cleaner directly to the computer; use a soft clean cloth. Do not use volatile (petroleum distillates) or abrasive cleaners on any part of the computer. Servicing Do not attempt to service the computer yourself. Doing so may violate your warranty and expose you and the computer to electric shock.
Page 11: Travel Considerations
Preface Travel Considerations Packing As you get ready for your trip, run through this list to make sure the system is ready to go: Check that the battery pack and any spares are fully charged. Power off the computer and peripherals. Close the display panel and make sure it’s latched.
Page 12 Preface On the Road In addition to the general safety and maintenance suggestions in this preface, and Chapter 8: Troubleshoot- ing, keep these points in mind: Hand-carry the notebook - For security, don’t let it out of your sight. In some areas, computer theft is very common.
Page 13 Preface Developing Good Work Habits Developing good work habits is important if you need to work in front of the computer for long periods of time. Improper work habits can result in discomfort or serious injury from repetitive strain to your hands, wrists or other joints.
Page 14 Preface Lighting Proper lighting and comfortable display viewing angle can reduce eye strain and muscle fatigue in your neck and shoulders. • Position the display to avoid glare or reflections from overhead lighting or outside sources of light. • Keep the display screen clean and set the brightness and contrast to levels that allow you to see the screen clearly.
Page 15: Table Of Contents
Preface Contents Notice ................I Ap-Key Buttons & Keyboard ........ 1-10 FCC Statement ............II Function Keys ............1-11 Instructions for Care and Operation ..... IV System Map: Front View (Audio "DJ") ....1-12 Power Safety ............VI Audio "DJ" CD Player ........... 1-13 Battery Precautions ..........VII System Map: Rear View ........
Page 16 Preface Auto Mail Checker ...........2-8 Battery Life ............3-9 Application Ap-Key ..........2-10 Recharging the Battery with the AC/DC Adapter 3-10 TouchPad and Buttons/Mouse .......2-11 Proper handling of the Battery Pack ....3-11 Configuring the TouchPad and Buttons ....2-11 Battery FAQ ............3-12 Audio Features ............2-12 Drivers &...
Page 17 Preface Module Drivers ............4-11 Legacy USB Support (Advanced Menu) ....5-9 Wireless LAN .............4-11 Boot-time Diagnostic Screen: (Advanced Menu) ..5-9 Bluetooth .............4-11 Reset Configuration Data: (Advanced Menu) ..5-9 PC Camera ............4-11 Power on Boot Beep/Battery TV Tuner Options ..........4-11 Low Alarm Beep: (Advanced Menu) ......
Page 18 Preface Intel PRO/Wireless Mini-PCI WLAN Module ..7-2 Upgrading and Adding New Hardware/Software ..8-5 Intel WLAN Driver Installation ......7-3 Problems and Solutions ........... 8-7 Bluetooth Module .............7-4 Interface (Ports & Jacks) Bluetooth Driver Installation ........7-4 Bluetooth Audio Setup ..........7-6 Overview ..............A-1 PC Camera Module ..........7-8 Notebook Ports and Jacks ........
Page 19 Preface ATI Video Driver Controls Power ...............C-6 Environmental Spec ..........C-6 ATI Video Driver Installation ......... B-1 Physical Dimensions & Weight .......C-6 ATI Mobility Radeon Properties ......B-2 Optional ..............C-7 Display Devices ............B-4 Attaching Other Displays ........B-5 Display Modes ............B-6 Clone Mode ............
Page 20 Preface XVIII...
Page 21: Quick Start Guide
Quick Start Guide Chapter 1: Quick Start Guide Overview This Quick Start Guide is a brief introduction to the basic features of your computer, to navigating around the computer and to getting your system started. The remainder of the manual covers the following: •...
Page 22: Model Differences
Quick Start Guide Model Differences This notebook series includes two different model types. The models differ slightly in design style including the LCD type, and AC/DC adapter. See Figure 1 - 1 below and Table 1 - 1, on page 1 - 3 for an outline of the model differences (Model B includes two different design types).
Page 23 Quick Start Guide Feature Model A Model B Processor Options Pentium M & Celeron M Processor Options Pentium M Processor Options Only (See Page Design Types 1 * Design Type 2 * Design Types 17.0" WXGA (1440*900) Flat Panel TFT 15.4"...
Page 24: Advanced Users
Quick Start Guide Advanced Users If you are an advanced user you may skip over most of this Quick Start Guide. However you may find it useful to refer to “What to Install” on page 4 - “BIOS Utilities” on page 5 - 1 “Upgrading The Computer”...
Page 25: Not Included
Quick Start Guide Not Included Operating Systems (e.g. Windows XP) and applications (e.g. word processing, spreadsheet and database pro- grams) have their own manuals, so please consult the appropriate manuals. System Software Your computer may already come with system software pre-installed. Where this is not the case, or where you are re-configuring your computer for a different system, you will find this manual refers to the Microsoft Win- dows XP (Home &...
Page 26: System Startup
Quick Start Guide System Startup Remove all packing materials. Place the computer on a stable surface. Securely attach any peripherals you want to use with the notebook (e.g. keyboard and mouse) to their ports. Attach the AC/DC adapter to the DC-In jack at the rear of the computer, then plug the AC power cord into an outlet, and connect the AC power cord to the AC/DC adapter.
Page 27: System Map: Model A - Front View With Lcd Panel Open
Quick Start Guide System Map: Model A - Front View with LCD Panel Open Figure 1 - 2 Front View - LCD Panel Open Wireless Device Optional Built-In PC Camera Operation Aboard Aircraft Ap-Key Buttons Power Button The use of any portable Keyboard electronic transmission...
Page 28: System Map: Model B - Front View With Lcd Panel Open
Quick Start Guide System Map: Model B - Front View with LCD Panel Open Figure 1 - 3 Front View - LCD Panel Open Wireless Device Optional Built-In PC Camera Operation Aboard Aircraft Ap-Key Buttons Power Button The use of any portable Keyboard electronic transmission...
Page 29: Led Indicators
Quick Start Guide LED Indicators Icon Color Description The LED indicators on the computer display helpful Orange The Battery is Charging information about the current status of the computer. Blinking The Battery has Reached Critically Orange Low Power Status Table 1 - 2 - LED Indicators Green The Battery is Fully Charged Second Battery Indicator...
Page 30: Ap-Key Buttons & Keyboard
Quick Start Guide Ap-Key Buttons & Keyboard The keyboard has an embedded numerical keypad for easy numeric data input, and features Function Keys to These buttons give instant access to the default Inter- allow you to change operational features instantly (see net browser and e-mail program, and to a user-defined Figure 1 - 4).
Page 31: Function Keys
Quick Start Guide Function Keys To use the function keys, press and hold the Fn key, then press the appropriate function key (F3 - F12 etc.). Function Function Function Key Fn + F9 Increase LCD Brightness Fn + F3 Mute Toggle Fn + F10 PC Camera Module Power Toggle Fn + F4...
Page 32: System Map: Front View (Audio "Dj")
Quick Start Guide System Map: Front View (Audio "DJ") Figure 1 - 5 - Front View (Audio "DJ") Audio "DJ" Power Button Volume Down Volume Up Audio "DJ" MP3 Track Limit Repeat LED Display There is a track limit of 256 tracks on any MP3 CD/ Previous Track DVD.
Page 33: Audio "Dj" Cd Player
Quick Start Guide Audio "DJ" CD Player The built-in standalone audio CD player gives direct hardware control for audio CDs/DVDs when the com- TV Tuner Option puter is shut down, but has a working power source. If you have included the optional TV Tuner in your purchase configuration, you can use the supplied re- Make sure that the computer is shut down (i.e.
Page 34: System Map: Rear View
Quick Start Guide System Map: Rear View Rear View - Model A Rear View - Model B 9 10 Figure 1 - 6 - Rear View Vent/Fan Intake/Outlet S/PDIF-Out Jack Overheating Line-In Jack To prevent your computer from overheating make 2 * USB 2.0 Ports sure nothing blocks the Vent/Fan Intake/Outlet DVI-Out Port...
Page 35: System Map: Right View
Quick Start Guide System Map: Right View Right View - Model A Right View - Model B Figure 1 - 7 - Right View Headphone-Out Jack Mini-IEEE 1394a Port Mini-IEEE 1394a Port Microphone-In Jack 2 * USB 2.0 Ports Both Mini-IEEE 1394a ports only support 4-in-1 Card Reader Security Lock Slot SELF POWERED IEEE 1394a devices.
Page 36: System Map: Left View
Quick Start Guide System Map: Left View Figure 1 - 8 - Left View Left View - Model A Security Lock Slot Speaker Optional Device Drive Bay Left View - Model B (for CD/DVD Device - see page 3, or 2nd PATA Hard Disk, or 2nd Battery) CD/DVD Emergency Eject Changing DVD Regional Codes...
Page 37: System Map: Bottom View
Quick Start Guide System Map: Bottom View Model A Model B Figure 1 - 9 - Bottom View Vent/Fan Intake/Outlet Battery Information Video Card Cover (Model A) Battery Always completely discharge, then fully charge, a Optical Device Release Latches new battery before using it. Completely discharge HDD / RAM Bay Cover (Model A) and charge the battery at least once every 30 days or Video Card / HDD / RAM Bay Cover (Model B)
Page 38: Windows Xp Start Menu & Control Panel
Quick Start Guide Windows XP Start Menu & Control Panel Most of the control panels, utilities and programs within Windows XP (and most other Windows versions) are accessed from the Start menu. When you install programs and utilities they will be installed on your hard disk drive, and a shortcut will usually be placed in the Start menu and/or the desktop.
Page 39: Video Features
Quick Start Guide Video Features This computer features Two different PCI Express video cards, depending on the model purchased (see “Video Card Options” on page C - 3). Model A computers feature an ATI Mobility Radeon X700 (M26) video card with 128/256MB DDR video RAM on board;...
Page 40 Quick Start Guide Figure 1 - 11 - Display Properties Desktop ATI Mobility Radeon Properties The pictures used in Figure 1 - 11 are taken from the ATI Mobility Radeon X700 properties tabs. If your purchase option includes the ATI Mobility Radeon X800 XT video card, then the properties tabs may appear slightly different. 1 - 20 Video Features...
Page 41: Display Devices & Options
Quick Start Guide Display Devices & Options Besides the built-in LCD, you can also use an external VGA monitor (CRT)/external Flat Panel Display or TV as your display device. A VGA monitor/Flat Panel Display connects to the DVI-Out port, a TV to the S- Video-Out jack.
Page 42: Power Management Features
Quick Start Guide Power Management Features The Power Options control panel icon in Windows (see page 18) allows you to configure power management features for your computer. You may conserve power through individual components such as the monitor or hard disk (by means of Power Schemes), or you may use either Standby or Hibernate mode to conserve power throughout the system (enable Hibernate support from the control panel as pictured in Figure 1 -...
Page 43: Features & Components
Features & Components Chapter 2: Features & Components Overview Read this chapter to learn more about the following main features and compo- nents of the computer: • Hard Disk Drive • Optical (CD/DVD) Device • 4-in-1 Card Reader • PC Card Slot •...
Page 44: Hard Disk Drive
Features & Components Hard Disk Drive The hard disk drive is used to store your data in the computer. The hard disk Power Safety can be taken out to accommodate other 2.5" serial (SATA) hard disk drives with a height of 9.5 mm. Before attempting to access any of the inter- The hard disk is accessible from the bottom of your computer as seen below.
Page 45: Optical (Cd/Dvd) Device
Features & Components Optical (CD/DVD) Device There is a bay for a 5.25" optical (CD/DVD) device (12.7mm height). The ac- Sound Volume tual device will depend on the module you purchased (see “Storage” on Adjustment page C - 4). The optical device is usually labeled “Drive D:” and may be used as a boot device if properly set in the BIOS (see “Boot Menu”...
Page 46: Handling Cds Or Dvds
Features & Components Handling CDs or DVDs Proper handling of your CDs/DVDs will prevent them from being damaged. Please follow the advice below to make sure that the data stored on your CDs/ CD Emergency Eject DVDs can be accessed. If you need to manually Note the following: eject a CD (e.g.
Page 47: Dvd Regional Codes
Features & Components DVD Regional Codes To change the DVD regional codes see “Changing DVD Regional Codes” on page 1 - DVD Regional Coding Table 2 - 1 DVD Regional Coding Region Geographical Location USA, Canada Western Europe, Japan, South Africa, Middle East &...
Page 48: 4-In-1 Card Reader
Features & Components 4-in-1 Card Reader The card reader allows you to use some of the latest digital storage cards. Push Card Reader Cover the card into the slot and it will appear as a removable device, and can be ac- cessed in the same way as your hard disk (s).
Page 49: Pc Card Slot
Features & Components PC Card Slot The computer is equipped with a PCMCIA 3.3V/5V slot for one type II PC- PC Card Slot Cover MCIA CardBus PC Card Slot. Make sure you install the PCMCIA/Card Read- er Card driver (see “PCMCIA/Card Reader”...
Page 50: Auto Mail Checker
Features & Components Auto Mail Checker After you have installed the driver for the Auto Mail Checker program (see “AutoMail” on page 4 - 11) you may then configure it to give you notification when you receive new mail. You must be online to receive this notification (note that this program only supports the POP3 protocol), and your default mail program does not need to be open.
Page 51 Features & Components You may then configure the options for your mailserver, name, password, pro- gram and method(s) of notification. Note Check with your Inter- net Service Provider, network administrator or Mail Service provid- er for details on what to put on these pages.
Page 52: Application Ap-Key
Features & Components Application Ap-Key The Ap-key buttons give instant access to the default Internet browser and e- Application.exe mail program, and to a user-defined application, with one quick button press. To configure a program to open when the application Ap-key is pressed You will need to locate the actual application...
Page 53: Touchpad And Buttons/Mouse
Features & Components TouchPad and Buttons/Mouse The TouchPad is an alternative to the mouse; however, you can also add a Mouse Driver mouse to your computer through one of the USB ports. The TouchPad buttons function in much the same way as a two-button mouse. The central button may If you are using an ex- be configured to function as you require.
Page 54: Audio Features
Features & Components Audio Features You can configure the audio options on your computer from the Sounds and Sound Volume Audio Devices Windows control panel, or from the Sound Effect Man- Adjustment ager icon in the taskbar/control panel (this will bring up the Realtek Audio How high the sound Configuration menus).
Page 55: Adding A Printer
Features & Components Adding a Printer The most commonly used peripheral is a printer. The following conventions Parallel Printer will help you to add a printer, however it is always best to refer to the printer manual for specific instructions and configuration options. After setting up the printer attach the paral- lel cable to the printer.
Page 56 Features & Components 2 - 14...
Page 57: Power Management
Power Management Chapter 3: Power Management OS Note Overview Power management To conserve power, especially when using the battery, your computer uses the functions will vary ACPI power management system. Power management conserves power by slightly depending on controlling individual components of the computer (the monitor and hard disk your operating system.
Page 58: The Power Sources
Power Management The Power Sources The computer can be powered by either an AC/DC adapter or a battery pack. AC/DC Adapter Use only the AC/DC adapter that comes with your computer. The wrong type of AC/DC adapter will damage the computer and its components. Attach the AC/DC adapter to the DC-in jack at the rear of the computer.
Page 59: Turning On The Computer
Power Management Turning on the Computer Now you are ready to begin using your computer. To turn it on simply press Shutdown the power button on the front panel. Note that you should always shut your com- When the computer is on, you can use the power button as a Standby/Hiber- puter down by choos- nate/Shutdown hot-key button when it is pressed for less than 4 seconds Turn...
Page 60: Power Schemes
Power Management Power Schemes You can set your computer to conserve power through individual components Resuming by means of Power Schemes. You can also adjust the settings for each Operation scheme to set the monitor to turn off after a specified time, and the computer's The system can re- hard disk motor to turn off if the hard disk drive has not been accessed for a sume from Monitor or...
Page 61 Power Management Each Windows Power Scheme will also adjust the processor performance of your machine in order to save power. This is worth bearing in mind if you are experiencing any reduced performance (especially under DC/battery power). Choose the Home/Office Desk scheme for maximum performance when the computer is powered from an AC power source.
Page 62: System Power Options
Power Management System Power Options You can use the system power options to stop the computer’s operation and restart where you left off. This system features Standby and Hibernate sleep mode levels (Hibernate mode will need to be enabled by clicking the option in the Hibernate tab in the Power Options control panel - Figure 3 - 2 on page 3 -...
Page 63: Standby
Power Management Standby Standby saves the least amount of power, but takes the shortest time to return to full operation. During Standby the hard disk is turned off, and the CPU is System Resume made to idle at its slowest speed. All open applications are retained in memo- The system can resume ry.
Page 64: Configuring The Power Button
Power Management Configuring the Power Button The power button may be set to send the computer in to either Standby or Hi- bernate mode (Figure 3 - 3). In Standby mode, the LED will blink green. In Hibernate mode the LED will be off. If you are in a power saving mode set to save power through individual components (e.g.
Page 65: Battery Information
Power Management Battery Information Please follow these simple guidelines to get the best use out of your battery. Low Battery New Battery Warning Always completely discharge, then fully charge, a new battery (see “Battery When the battery is FAQ” on page 3 - 12 for instructions on how to do this).
Page 66: Recharging The Battery With The Ac/Dc Adapter
Power Management Battery life may be shortened through improper maintenance. To optimize the life and improve its performance, fully discharge and recharge the battery at least once every 30 days. Conserving Battery Power We recommend that you do not remove the battery yourself. If you do need to remove the battery for any reason see “Removing the Battery”...
Page 67: Proper Handling Of The Battery Pack
Power Management Proper handling of the Battery Pack • DO NOT disassemble the battery pack under any circumstances • DO NOT expose the battery to fire or high temperatures, it may explode • DO NOT connect the metal terminals (+, -) to each other Damaged Battery Warning Should you notice any physical defects (e.g.
Page 68: Battery Faq
Power Management Battery FAQ How do I completely discharge the battery? Use the computer with battery power until it shuts down due to a low battery. Caution Don’t turn off the computer by yourself even when you see a message that in- Danger of explosion if dicates the battery is critically low, just let the computer use up all of the bat- battery is incorrectly...
Page 69: Drivers & Utilities
Drivers & Utilities Chapter 4: Drivers & Utilities What to Install This chapter deals with installing the drivers and utilities essential to the operation or improvement The Device Drivers & Utilities + User’s Manual of some of the computer’s subsystems. The system CD-ROM contains the drivers and utilities neces- takes advantage of some newer hardware compo- sary for the proper operation of the computer.
Page 70 Drivers & Utilities Navigate (Browse..) to D: You will notice that many of the instructions for driver installation require you to “Navigate (Browse) to D:”. We assume that you will install all drivers and utilities from the built-in CD device and it is assigned to “Drive D:”.
Page 71: Service Packs
Drivers & Utilities Service Packs Check the warnings on the following pages regard- ing installation of the appropriate Service Pack for Windows XP Service Pack 2 your Windows OS. Make sure you have installed Make sure you install Windows XP Service Pack 2 the appropriate Service Pack before installing all (or a Windows XP version which includes Service the drivers.
Page 72: Authorized Driver Message
Drivers & Utilities Authorized Driver Message Updating/Reinstalling Individual Drivers If you receive a message telling you that the driver you are installing is not authorized (Digital Signa- If you wish to update/reinstall individual drivers it ture Not Found), just click Yes or Continue Any- may be necessary to uninstall the original driver.To way to ignore the message and continue the do this go to the Control Panel in the Windows OS...
Page 73: Driver Installation
Drivers & Utilities Driver Installation NoteBook Driver Installation Application Check the driver installation order from Table 4 - Insert the Device Drivers & Utilities + User’s Man- 1, on page 4 - 6 (the drivers must be installed ual CD-ROM and the NoteBook Driver Installa- in this order).
Page 74: Driver Installation Procedure
Drivers & Utilities Driver Installation Procedure WinXP SP2 Driver Page # This section covers driver and utility installation in- structions for Windows XP Home & Professional Install the appropriate Service Pack for WinXP Page 4 - 3 (with Service Pack 2 installed). Chipset Page 4 - 7 Video (VGA)
Page 75: Chipset
Drivers & Utilities Chipset Video(VGA) 1. Double-click Chipset from the Notebook 1. Double-click VIDEO from the Notebook Driver Installation menu. Driver Installation menu. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse..) to (Browse..) to (one of the following) D:\Drivers\00Chipset\Setup.exe and click D:\Drivers\01Vga\ATIM26\Setup.exe D:\Drivers\01Vga\ATIM28\Setup.exe...
Page 76: Audio
Drivers & Utilities Audio Modem 1. Double-click Audio from the Notebook Driver 1. Double-click Modem from the Notebook Installation menu. Driver Installation menu. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse..) to (Browse..) to (one of the following) D:\Drivers\02Audio\Setup.exe and click OK.
Page 77: Lan
Drivers & Utilities AP-Key Buttons 1. Double-click LAN from the NoteBook 1. Double-click AP-key from the Notebook Driver Installation menu. Driver Installation menu. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse..) to (one of the following) (Browse..) to (one of the following) D:\Drivers\04Lan\Marvell\SetupYukon- D:\Drivers\05Ap-key\Setup.exe...
Page 78: Touchpad
Drivers & Utilities TouchPad PCMCIA/Card Reader 1. Double-click Touchpad from the Notebook 1. Double-click PCMCIA from the Notebook Driver Installation menu. Driver Installation menu. Click Start (menu) > Run... and navigate Click Start (menu) > Run... and navigate (Browse...) to (Browse...) to D:\Drivers\06Touchpad\SETUP.EXE and D:\Drivers\07PCMCIA\setup.exe and...
Page 79: Automail
Drivers & Utilities AutoMail Bluetooth 1. Double-click AutoMail from the Notebook See the installation procedure in “Bluetooth Mod- ule” on page 7 - Driver Installation menu. PC Camera Click Start (menu) > Run... and navigate See the installation procedure in “PC Camera (Browse..) to Module”...
Page 80 Drivers & Utilities 4 - 12...
Page 81: Bios Utilities
BIOS Utilities Chapter 5: BIOS Utilities BIOS Settings Overview Warning This chapter gives a brief introduction to the computer’s built-in software: Incorrect settings can cause your system to Diagnostics: The POST (Power-On Self Test) malfunction. To correct mistakes, return Setup and restore the Configuration: The Setup utility Setup Defaults with If your computer has never been set up, or you are making important changes...
Page 82: The Power-On Self Test (Post)
BIOS Utilities The Power-On Self Test (POST) Each time you turn on the computer, the system takes a few seconds to con- POST Screen duct a POST, including a quick test of the on-board RAM (memory). 1.BIOS information As the POST proceeds, the computer will tell you if there is anything wrong. 2.CPU type If there is a problem that prevents the system from booting, it will display a 3.Memory status...
Page 83: Failing The Post
BIOS Utilities Failing the POST Errors can be detected during the POST. There are two categories, “fatal” and “non-fatal”. Fatal Errors These stop the boot process and usually indicate there is something seriously wrong with your system. Take the computer to your service representative or authorized service center as soon as possible.
Page 84: The Setup Program
BIOS Utilities The Setup Program The Phoenix Setup program tells the system how to configure itself and man- age basic features and subsystems (e.g. port configuration). Entering Setup To enter Setup, turn on the computer and press F2 during the POST. The prompt (Press F2 to Enter Setup) seen in Figure 5 - 1 is usually present for a...
Page 85: Setup Screens
BIOS Utilities Setup Screens The following pages contain additional advice on portions of the Setup. Setup Menus Along the top of the screen is a menu bar with five (5) menu headings. When Setup menus you select a heading, a new screen appears. Scroll through the features listed shown in this section on each screen to make changes to Setup.
Page 86: Main Menu
BIOS Utilities Main Menu PhoenixBIOS Setup Utility Figure 5 - 2 Main Main Advanced Security Boot Exit Main Menu Item Specific Help System Time: [22:11:05] System Date: [07/21/2005] IDE Channel 0 Master [20004MB] <Tab>, <Shift Tab>, or IDE Channel 0 Slave [CD-ROM] <Enter>...
Page 87: Ide Channel 0 Master/Slave (Main Menu)
BIOS Utilities IDE Channel 0 Master/Slave (Main Menu) Pressing Enter opens the sub-menu to show the configuration of either a CD Device or HDD that on the computer’s IDE Channel 0. Use the Auto (Type:) setting to have the items configured automatically for you. SATA Port 1(Main Menu) Pressing Enter here opens the sub-menu to show the configuration of any hard disks on the computer’s SATA Port 1.
Page 88: Advanced Menu
BIOS Utilities Advanced Menu Figure 5 - 3 PhoenixBIOS Setup Utility Advanced Menu Main Advanced Advanced Security Boot Exit Item Specific Help Advanced Chipset Control Select options for Advanced Chipset National 383 SIO Control Sub-Menu features. Legacy USB Support: [Enabled] Boot-time Diagnostic Screen: [Enabled] Reset Configuration Data:...
Page 89: National 383 Sio Control Sub-Menu (Advanced Menu)
BIOS Utilities National 383 SIO Control Sub-Menu (Advanced Menu) Pressing Enter here will provide a sub-menu that controls the configuration of National 383 SIO devices such as the serial port, and/or the infrared transceiver (FIR Device). Legacy USB Support (Advanced Menu) Use this menu item to enable/disable the support for Legacy Universal Serial Bus.
Page 90: Security Menu
BIOS Utilities Security Menu Figure 5 - 4 PhoenixBIOS Setup Utility Security Menu Security Main Advanced Security Boot Exit Item Specific Help Supervisor Password Is: Clear Set Supervisor Password [E E nter] Supervisor Password Password on boot: [Disabled] controls access to the setup utility.
Page 91: Password On Boot: (Security Menu)
BIOS Utilities Password on boot: (Security Menu) Specify whether or not a password (supervisor or user password) should be entered to boot the computer. If “Enabled” is selected, only users who enter a Password Warning correct password can boot the system (see the warning in the sidebar). The If you set a boot pass- default setting is “Disabled”.
Page 92: Boot Menu
BIOS Utilities Boot Menu PhoenixBIOS Setup Utility Figure 5 - 5 Main Advanced Security Exit Boot Boot Menu Item Specific Help Boot priority order: 1: IDE 0: TOSHIBA MK2023GAS-(PM) Keys used to view or 2: IDE 1: PIONEER DVD-RW DVR-K15RA- configure devices: 3: IDE 2: Up and Down arrows...
Page 93 BIOS Utilities When you specify a device as a boot device on the Boot Menu, it requires the availability of an operating system on that device. Most home computers come with an operating system already installed on “Drive C:”. If you wish to boot from a CD-ROM/DVD-ROM you will need to add it to the boot order.
Page 94: Configuring The Network Boot Protocol
BIOS Utilities Configuring the Network Boot Protocol Figure 5 - 6 Boot Agent Menu Realtek RTL8110S/8169S Gigabit Boot Agent Press Shift-F10 to configure ..Enabling Network Boot Realtek RTL8110S/8169S Gigabit Boot Agent Configuration Menu v1.50 Go to the Advanced > Advanced Chipset Control menu to en-...
Page 95: Exit Menu
BIOS Utilities Exit Menu Figure 5 - 7 PhoenixBIOS Setup Utility Exit Menu Main Advanced Security Boot Exit Exit Item Specific Help Exit Saving Changes Exit Discarding Changes Exit System Setup and Load Setup Defaults save your changes to CMOS. Discard Changes Save Changes Help...
Page 96 BIOS Utilities 5 - 16...
Page 97: Upgrading The Computer
Upgrading The Computer Chapter 6: Upgrading The Computer Overview This chapter contains information on upgrading the computer. Follow the Warranty Warning steps outlined to make the desired upgrades. If you have any trouble or prob- lems you can contact your service representative for further help. Before you Please check with your begin you will need: service representative...
Page 98: When Not To Upgrade
Upgrading The Computer When Not to Upgrade These procedures involve opening the system’s case, adding and sometimes replacing parts. Power Safety Warning You should not perform any of these upgrades if: Before you undertake any upgrade proce- • Your system is still under warranty or a service contract dures, make sure that you have turned off the •...
Page 99: Removing The Battery
Upgrading The Computer Removing the Battery If you are confident in undertaking upgrade procedures yourself, for safety Warranty Warning reasons it is best to remove the battery. Please check with your Turn the computer off, and turn it over. service representative Slide the latch in the direction of the arrow, and hold it in place.
Page 100: Upgrading The Hard Disk Drive
Upgrading The Computer Upgrading the Hard Disk Drive The hard disk drive can be taken out to accommodate other 2.5" serial (SATA) HDD System hard disk drives with a height of 9.5mm (h) (see “Storage” on page C - Warning Follow your operating system’s installation instructions, and install all neces- New HDD’s are blank.
Page 101 Upgrading The Computer For Model A computers (see overleaf for Model B): Remove screws from the hard disk assembly. Pull the tab upward and lift the assembly out of the computer. Remove the 4 screws to release the hard disk from the assembly cover, and remove the connector Reverse the process to install any new hard disk.
Page 102 Upgrading The Computer For Model B computers: Remove screws & from the hard disk assembly. Pull the tab upward and lift the assembly out of the computer. Remove the 4 screws to release the hard disk from the assembly cover. 10.
Page 103: Upgrading The Optical (Cd/Dvd) Device
Upgrading The Computer Upgrading the Optical (CD/DVD) Device Turn off the computer, and turn it over and remove the battery. Slide the latch in the direction of the arrow, and hold it in place. Eject the optical device by carefully sliding the latch in the direction of the arrow.
Page 104: Upgrading The System Memory (Ram)
Upgrading The Computer Upgrading the System Memory (RAM) The computer has two memory sockets for 200 pin Small Outline Dual In-line (SO-DIMM) DDRII (DDR2) type memory modules (see “Memory” on page C - 2 for details of supported module types). The total memory size is automatically detected by the POST routine once you turn on your computer.
Page 105 Upgrading The Computer Gently pull the two release latches on the sides of the memory socket in the direction indicated by the arrows ( & ) in Figure 6 - Figure 6 - 7 RAM Module Location Contact Warning Be careful not to touch the metal pins on the The RAM module will pop-up, and you can remove it.
Page 106 Upgrading The Computer Pull the latches to release the second module if necessary. Insert a new module holding it at about a 30° angle and fit the connectors firmly into the memory slot. The module’s pin alignment will allow it to only fit one way. Make sure the module is seated as far into the slot as it will go.
Page 107: Inserting The 2Nd Hard Disk
Upgrading The Computer Inserting the 2nd Hard Disk Turn off the computer, and turn it over and remove the battery. Inserting the 2nd Slide the latch in the direction of the arrow, and hold it in place. Hard Disk Eject the installed device (CD/DVD, battery or HDD) by carefully sliding the latch in the direction of the arrow.
Page 108: Upgrading The Processor
Upgrading The Computer Upgrading the Processor If you want to upgrade your computer by replacing the existing processor with Warranty a faster/new one you will need to contact your customer service representa- tive. We recommend that you do not do this yourself, since if it is done incor- The CPU is not a user serviceable part.
Page 109: Modules & Options
Modules & Options Chapter 7: Modules & Options Wireless Device Overview Operation Aboard Aircraft This chapter contains the information on the WLAN, Bluetooth, PC Camera and TV Tuner modules which may come with your computer, depending on The use of any porta- the configuration purchased.
Page 110: Intel Pro/Wireless Mini-Pci Wlan Module
Modules & Options Intel PRO/Wireless Mini-PCI WLAN Module If you have included an Intel PRO/Wireless 2915ABG (802.11a/b/g) Mini- Wireless Device PCI WLAN module in your purchase option, you will have the appropriate Operation Aboard software CD provided for your module. Aircraft The use of any portable Before installing the Intel PRO/Wireless 2915ABG Mini-PCI WLAN driv-...
Page 111: Intel Wlan Driver Installation
Modules & Options Intel WLAN Driver Installation 1. Make sure the module is powered on, then insert the Intel PROSet/ Wireless CD-ROM into the CD/DVD drive. User Guide 2. Click Install Software (button). You can view the User 3. Click the button to accept the license and click Next > Next > OK. Guides by inserting the 4.
Page 112: Bluetooth Module
Modules & Options Bluetooth Module If you have included an Bluetooth module in your purchase option, you will Wireless Device have the appropriate software CD provided for your module. Operation Aboard Aircraft Before installing the Bluetooth driver, make sure that the optional Bluetooth The use of any portable module is on (the LED will be green).
Page 113 Modules & Options User Guide Send To Bluetooth View the BlueSoleil Right-Click to select any User Guides from the file and scroll down to Send Help Menu (or press To ... Bluetooth Device. the F1 key) in the IVT Corporation BlueSo- leil - Main Window control panel.
Page 114: Bluetooth Audio Setup
Modules & Options Bluetooth Audio Setup If you wish to use Bluetooth audio devices, it is necessary to setup the audio recording options in Windows (see Figure 7 - 4 on page 7 - Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds &...
Page 115 Modules & Options Figure 7 - 4 Bluetooth Audio Setup (Windows XP) Click to make volume controls appear. Bluetooth Module 7 - 7...
Page 116: Pc Camera Module
Modules & Options PC Camera Module If you have included an PC Camera module in your purchase option, you will Taking Still have the appropriate software CD provided for your module. Pictures Before installing the PC Camera driver, make sure that the optional PC Cam- Double-click the My era is on (the LED will be green).
Page 117: Sertek Pc Camera Driver Installation (Winxp)
Modules & Options Sertek PC Camera Driver Installation (WinXP) 1. Press the Fn + F10 key combination to power on the PC Camera module (click Cancel if you see a “New Hardware Found” message) . 2. Insert the PC Camera CD-ROM into the CD/DVD drive. 3.
Page 118: Pc Camera Audio Setup
Modules & Options PC Camera Audio Setup If you wish to capture video & audio with your camera, it is necessary to setup the audio recording options in Windows (see Figure 7 - 5 on page 7 - 11). Go to the Start menu and point to Settings (or just click Control Panel) and click Control Panel, then double-click the Sounds &...
Page 119 Modules & Options Figure 7 - 5 PC Camera Audio Setup (Windows XP) PC Camera Module 7 - 11...
Page 120: Bisoncap
Modules & Options BisonCap BisonCap is a video viewer useful for general purpose video viewing and test- ing, and can capture video files to .avi format. Pre-Allocating File Space Run the BisonCap program from the Start > Programs/All Programs > You may pre-allocate BisonCam menu (it is recommended that you set the capture file before the file size for the cap-...
Page 121: Eliminating Screen Flicker
Modules & Options Eliminating Screen Flicker If you find that the video screen in the BisonCap program is flickering, you can try to adjust the setting in the Video Capture Filter options. Run the BisonCap program. Go to Options and scroll down to select “Video Capture Filter...”. Click either 50Hz or 60Hz under Frequency in Property Page (tab).
Page 122: Tv Tuner Module Options
Modules & Options TV Tuner Module Options You may have one of two possible optional Mini-PCI TV Tuner modules sup- TV Tuner Remote plied with your computer, depending on your purchase configuration. The op- The remote control unit tional TV Tuner allows you to watch TV, play music CDs, video conference provided with the op- and capture still images and video on your PC.
Page 123: Lifeview Flydvb-T Hybrid Mini-Pci Tv Tuner Module
Modules & Options LifeView FlyDVB-T Hybrid Mini-PCI TV Tuner Module If your purchase includes the LifeView FlyDVB-T Hybrid Mini-PCI TV Tuner Module, then install the driver and application as per the instructions User Manual below. Insert the TV Tuner CD-ROM and double- Installing the LifeView FlyDVB-T Driver click Acrobat Reader 1.
Page 124: Yuan Pvr Mini-Pci Mpc622-Mce Tv Tuner Module
Modules & Options YUAN PVR Mini-PCI MPC622-MCE TV Tuner Module If your purchase includes the YUAN PVR MPC622-MCE TV Tuner for Win- MPC622-MCE dows XP Media Center Edition, then you will need to install the driver as per TV Tuner the instructions below.
Page 125: Troubleshooting
Troubleshooting Chapter 8: Troubleshooting Overview Should you have any problems with your computer, before consulting your service representative, you may want to try to solve the problem yourself. This chapter lists some common problems and their possible solutions. This can’t anticipate every problem, but you should check here before you panic. If you don’t find the answer in these pages, make sure you have followed the instructions carefully and observed the safety precautions in the preface.
Page 126: Basic Hints And Tips
Troubleshooting Basic Hints and Tips Many of the following may seem obvious but they are often the solution to a problem when your computer appears not to be working. • Power - Is the computer actually plugged into a working electrical outlet? If plugged into a power strip, make sure it is actually working.
Page 127: Backup And General Maintenance
Troubleshooting Backup and General Maintenance • Always backup your important data, and keep copies of your OS and programs safe, but close to hand. Don’t forget to note the serial numbers if you are storing them out of their original cases, e.g. in a CD wallet.
Page 128: Viruses
Troubleshooting Viruses • Install an Anti-Virus program and keep the definitions file (the file which tells your program which viruses to look for) up to date. New computer viruses are discovered daily, and some of them may seriously harm your computer and cause you to lose data. Anti-Virus programs are commercially available and the definitions file updates are usually downloadable directly from the internet.
Page 129: Upgrading And Adding New Hardware/Software
Troubleshooting Upgrading and Adding New Hardware/Software • Do not be tempted to make changes to your Windows Registry unless you are very sure of what you are doing, otherwise you will risk severely damaging your system. • Don’t open your computer or undertake any repair or upgrade work if you are not comfortable with what you are doing.
Page 130 Troubleshooting • Thoroughly check any recent changes you made to your system as these changes may affect one or more system components, or software programs. If possible, go back and undo the change you just made and see if the problem still occurs. •...
Page 131: Problems And Solutions
Troubleshooting Problems and Solutions Problem Possible Cause - Solution You turned on the power Battery missing / incorrectly installed. Check the battery bay, make sure the battery is but it doesn’t work. present and seated properly (the design of the battery only allows it to go in one way). Make sure there’s nothing interfering with the battery contacts.
Page 132 Troubleshooting Problem Possible Cause - Solution The computer feels too Make sure the computer is properly ventilated and the Vent/Fan intakes are not blocked. If hot. this doesn’t cool it down, put the system into Hibernate mode or turn it off for an hour. Make sure the computer isn’t sitting on a thermal surface (see “Overheating”...
Page 133 Troubleshooting Problem Possible Cause - Solution No image appears on the You haven’t installed the video driver and configured it appropriately from the Control external monitor I have Panel. See “ATI Video Driver Controls” on page B - 1 for instructions on installing and plugged in and powered configuring the video driver.
Page 134 Troubleshooting Problem Possible Cause - Solution The compact disc tray The compact disc is not correctly placed in the tray. Gently try to remove the disc using the will not open when there eject hole (see “Loading Discs” on page 2 - is a disc in the tray.
Page 135 Troubleshooting Problem Possible Cause - Solution Wireless LAN/ The driver(s) for the module(s) have not been installed. Make sure you have installed the Bluetooth/ PC Camera driver for the appropriate module (see the instructions for the appropriate module in modules cannot “Modules &...
Page 136 Troubleshooting 8 - 12...
Page 137: Interface (Ports & Jacks)
Interface (Ports & Jacks) Appendix A: Interface (Ports & Jacks) Overview The following chapter will give a quick description of the interface (ports & jacks) which allow your com- puter to communicate with external devices, connect to the internet etc. Interface (Ports &...
Page 138: Notebook Ports And Jacks
Interface (Ports & Jacks) Notebook Ports and Jacks Item Description Built-In Microphone The built-in microphone allows you to record on your computer Card Reader Port The card reader allows you to use some of the latest digital storage cards. Push the card into the slot and it will appear as a removable device.
Page 139: Line-In Jack
Interface (Ports & Jacks) Item Description Line-In Jack The Line-In jack allows you to play audio sources through the computer’s speakers. Microphone-In Jack Plug an external microphone in to this jack to record on your computer. Mini-IEEE 1394 Port This port allows a high-speed connection to various peripheral devices, e.g. external disk drives and digital cameras (see note below).
Page 140: Security Lock Slot
Interface (Ports & Jacks) Item Description Security Lock Slot To prevent possible theft, a Kensington-type lock can be attached to this slot. Locks can be purchased at any computer store. Serial Port Connect a serial type mouse to this port. S/PDIF-Out Jack This S/PDIF (Sony/Philips Digital Interface Format) Out Jack allows you to connect your DVD-capable PC to a Dolby AC-3 compatible receiver for “5.1”...
Page 141: Ati Video Driver Controls
ATI Video Driver Controls Appendix B: ATI Video Driver Controls The basic settings for configuring the LCD are outlined in “Video Features” on page 1 - ATI Video Driver Installation Make sure you install the drivers in the order indicated in Table 4 - 1, on page 4 - 1.
Page 142: Ati Mobility Radeon Properties
ATI Video Driver Controls ATI Mobility Radeon Properties More advanced video configuration options are provided in the ATI Mobility ATI Taskbar Icon Radeon X700/X800 XT Properties control panel: You can also access Open the Display Properties (see “Video Features” on page 1 - 19) con- ATI Mobility Radeon trol panel.
Page 143 ATI Video Driver Controls Help Menus Right-click on almost any item in the tabs to bring up the “What’s This?” button. Click “What’s This?” button to bring up the help menu. PowerPlay Menu Help Menu The menus pictured in this chapter are from Mobility Radeon X700.
Page 144: Display Devices
ATI Video Driver Controls Display Devices Besides the built-in LCD, you can also use an external monitor/flat panel dis- Theater Mode play or TV as your display device. The following are the display options: Theater Mode can be enabled clicking The built-in LCD.
Page 145: Attaching Other Displays
ATI Video Driver Controls Attaching Other Displays If you prefer to use a monitor or flat panel display, connect it to the DVI-Out Function Key Port at the rear of the computer. Combination Attach your external monitor to the DVI-Out port (or TV to the S-Video-Out You can use the Fn + port), and turn it on.
Page 146: Display Modes
ATI Video Driver Controls Display Modes Single Primary & Clone Only one of your displays is used. Displays The Primary display in Multiple - Clone Mode an Extended Desktop Clone Mode simply shows an exact copy of the Primary display desktop on environment will be as- the other display(s).
Page 147: Clone Mode
ATI Video Driver Controls Clone Mode Clone Mode simply shows an exact copy of the Primary display desktop on the other display(s). This mode will drive multiple displays with the same con- Display Data Channel tent. Use this feature to display the screen through a projector for a presenta- Information tion.
Page 148: Extended Desktop Mode
ATI Video Driver Controls Extended Desktop Mode The system supports Extended Desktop in multiple display environments in Windows XP. An Extended Desktop creates a desktop spanning multiple dis- plays and acts as a large workspace. To get this effect: Attach your external monitor to the DVI-Out port (or TV to the S-Video Out port), and turn it on.
Page 149 ATI Video Driver Controls 10. In the example shown in Figure B - 5 the primary monitor is on the left, the other display is on the right. Help Click either the Display pop- Further help is avail- up menu, or click the icon for able through the task- the appropriate display.
Page 150 ATI Video Driver Controls 12. One display will be set to Primary. The displays may be switched as long as one as set to Primary. Figure B - 6 Displays Tab In this picture the notebook LCD (Extended Desktop panel is the primary display, and the desktop may be extended to any at- Mode) tached displays.
Page 151: Enabling Tv Display
ATI Video Driver Controls Enabling TV Display To display desktop images on a TV, connect the TV to your computer by using an S-Video cable from the TV to the S-Video-Out jack at the rear of the com- puter (see “System Map: Rear View”...
Page 152 ATI Video Driver Controls The TV Properties tabs allow you to adjust the TV settings and TV Format etc. Figure B - 8 TV Properties (Adjustments & Format) B - 12 Enabling TV Display...
Page 153: Specifications
Specifications Appendix C: Specifications Latest Specification Information The specifications listed in this Appendix are correct at the time of going to press. Certain items (particularly pro- cessor types/speeds and CD/DVD device types) may be changed or updated due to the manufacturer's release schedule.
Page 154: Processor
Specifications Feature Specification µ Processor Intel Pentium® M Processor 0.09) 0.09 Micron Process Technology (478-pin) Micro-FC-PGA Package 2MB On-die L2 Cache & 533MHz FSB Models 730/ 740/ 750/ 760/ 770/ 780 1.6/ 1.73/ 1.86/ 2/ 2.13/ 2.26 GHz Celeron Processors are µ...
Page 155: Video Card Options
Specifications Feature Specification Video Card Model A Computers: Model B Computers: Options ATI Mobility Radeon X700 (M26) PCI ATI Mobility Radeon X700 (M26) PCI Express Video Card Express Video Card 128/256MB DDR Video RAM On Board 128MB DDR Video RAM On Board 256-bit Video Memory Interface 256-bit Video Memory Interface PCI Express * 16...
Page 156: Storage
Specifications Feature Specification Storage One Changeable 12.7mm(h) Optical Device (CD/DVD) Type Drive (see “Optional” on page C - for drive options) in Removable Bay One Removable Bay for 2 Battery or 2 PATA Hard Disk Drive or Optical Disk Drive Easy Changeable 2.5"...
Page 157: Card Reader
Specifications Feature Specification Interface & Four USB 2.0 Ports One RJ-11 Jack for Plug & Play Fax/Modem Communication One Mini-IEEE 1394 Port AZALIA 56K Plug & Play Fax/Modem One DVI-Out Port V.90/92 Compliant One Microphone-In Jack One Line-In Jack One RJ-45 Jack (Local Area Network) One Headphone-Out Jack 10MB/100MB/1Gbit PCI-Express One S/PDIF Output Jack...
Page 158: Keyboard & Pointing Device
Specifications Feature Specification Keyboard & Winkey Keyboard Built-In TouchPad with Scrolling Function Pointing Device PCMCIA One Type-II PCMCIA CardBus PC Card Slot Power Supports ACPI 2.0 Supports Hibernate Mode Management Supports Standby Power Power Supply - Model A Computers: Power Supply - Model B Computers: Full Range AC/DC Adapter 20V, Full Range AC/DC Adapter 20V, 4.5A (90 Watts), 100~240V, 47~63Hz...
Page 159: Optional
Specifications Feature Specification Optional Optical Drive Module Options: Bluetooth 1.2 Module with USB Interface DVD/CD-RW Combo Drive Module DVD-Dual Drive Module USB Floppy Disk Drive 8 Cell Smart Lithium-Ion Battery Pack, 4.4AH Battery - 6 Cell Smart Lithium-Ion Battery Pack, 3.8AH 300K Pixel PC VIdeo Camera Module with USB Interface (Factory Option) PATA Hard Disk Drive...
Page 160 Specifications C - 8...

EUROCOM Notebook User Manual

Quick Start Guide

Features & Components

Power Management

Drivers & Utilities

BIOS Utilities

Upgrading the Computer

Modules & Options

Troubleshooting

Interface (Ports & Jacks)

ATI Video Driver Controls

Specifications

Quick Links

Need help?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for EUROCOM Notebook

Summary of Contents for EUROCOM Notebook

Table of Contents