Table of Contents
Advertisement
5 PERIPHERAL CIRCUITS AND THEIR OPERATION (I/O Ports)
FOUT output (P16)
In order for the S1C88650 to provide clock signal to
an external device, a FOUT signal (oscillation clock
f
or f
dividing clock) can be output from
OSC1
OSC3
the P16 port terminal.
The output control for the FOUT signal is done by
the register FOUTON. When FOUTON is set to "1",
the FOUT signal is output from the P16 port
terminal, when "0" is set, the port is set for DC
output. When FOUTON is "1", settings of the I/O
control register IOC16 and data register P16D
become invalid.
The frequency of the FOUT signal can be selected in
software by setting the registers FOUT0–FOUT2.
The frequency is selected any one from among
eight settings as shown in Table 5.7.5.2.
Table 5.7.5.2 FOUT frequency setting
FOUT2
FOUT1
FOUT0
1
1
1
1
1
0
1
0
0
1
0
1
0
0
0
0
f
OSC1
f
OSC3
When the FOUT frequency is made "f
must turn on the OSC3 oscillation circuit before
outputting FOUT. A time interval of several msec
to several 10 msec, from the turning ON of the
OSC3 oscillation circuit to until the oscillation
stabilizes, is necessary, due to the oscillation
element that is used. Consequently, if an abnormal-
ity occurs as the result of an unstable FOUT signal
being output externally, you should allow an
adequate waiting time after turning ON of the
OSC3 oscillation, before turning outputting FOUT.
(The oscillation start time will vary somewhat
depending on the oscillator and on the externally
attached parts. Refer to the oscillation start time
example indicated in Chapter 8, "ELECTRICAL
CHARACTERISTICS".)
Since the FOUT signal is generated asynchronously
from the register FOUTON, when the signal is
turned ON or OFF by the register settings, a hazard
of a 1/2 cycle or less is generated.
Figure 5.7.5.2 shows the output waveform of the
FOUT signal.
FOUTON
0
FOUT output
(P16)
Fig. 5.7.5.2 Output waveform of FOUT signal
56
FOUT frequency
1
f
/ 8
OSC3
0
f
/ 4
OSC3
1
f
/ 2
OSC3
0
f
/ 1
OSC3
1
f
/ 8
OSC1
0
f
/ 4
OSC1
1
f
/ 2
OSC1
0
f
/ 1
OSC1
:
OSC1 oscillation frequency
:
OSC3 oscillation frequency
/n", you
OSC3
1
Inverted TOUT output (P17)
The S1C88650 provides an output of the TOUT2 or
TOUT3 inverted signal (programmable timer
output clock) to supply a clock to external devices
or to drive a buzzer.
By using this output with the TOUT2 or TOUT3
output from the P15 terminal, the bias level to be
applied to the buzzer can be increased.
The output control for the TOUTx signals (x = 2 or
3) is done by the registers RPTOUTx. When
RPTOUTx is set to "1", the TOUTx signal is output
from the P17 port terminal, when "0" is set, the port
is set for DC output. When RPTOUTx is "1",
settings of the I/O control register IOC17 and data
register P17D become invalid.
___________
___________
The TOUT2 and TOUT3 signals are generated from
the underflow and compare-match signals of the
programmable timers 2 and 3.
With respect to frequency control, see "5.10 Pro-
grammable Timer".
___________
Since the TOUTx signals are generated asynchro-
nously from the registers RPTOUTx, when the
signals are turned ON or OFF by the register
settings, a hazard of a 1/2 cycle or less is generated.
Figure 5.7.5.3 shows the output waveform of the
_________
TOUT signal.
RPTOUTx
TOUTx output
(P17)
Fig. 5.7.5.3 Output waveform of TOUT signal
Note: If RPTOUT2 and RPTOUT3 are set to "1" at
the same time, RPTOUT3 is effective.
EPSON
___________
___________
0
1
________
S1C88650 TECHNICAL MANUAL
Advertisement
Table of Contents
