Download Table of Contents Print this page

Brother S-7200B Service Manual page 16

Single needle direct drive straight lock stitcher with thread trimmer
Hide thumbs Also See for S-7200B:

Advertisement

Table of Contents
3. FUNCTION SETTINGS (OPERATION PANEL)
Function No. 41 − 55
No.
Initial value
41
0
42
0
43
0
44
0
45
80 (ms)
46
0
47
0
48
0
49
0
50
4000 (rpm)
51*
0
52
2 (needles)
10
53*
(needles)
54*
1
55
0
(NOTE 16)
(NOTE 15) Presser foot lifter pedal operation is not included. In the case of simultaneous operation, the standing operation
pedal takes priority.
(NOTE 16) Setting is only enabled when DIP switch 1 is set to ON.
*...
Settings indicated with " * " are enabled when the power is turned off and then back on.
9
Setting range
Presser foot lifting when treadle is depressed backward to 1st step after
returning to neutral
0 – 1
0: Possible
1: Not possible
Operation when treadle is depressed backward
0: Thread trimming operation
0 – 1
1: Thread trimming operation disabled (presser foot is raised when treadle is
depressed backward)
Depressed backward operation after treadle is returned to neutral and needle
stops in the up position
0 – 1
0: Single stitch is sewn and then the thread is trimmed (lock stitchers)
1: Thread wiping operation when needle is stopped in up position (chain
stitchers)
Operation when Standing operation variable speed pedal is on
0: Sewing speed corresponds to treadle depression amount
0 – 1
1: Sewing speed corresponds to sewing speed control key setting (constant
speed)
0 – 500 (ms)
Delay time from standing pedal turning on until motor starts operating
Operation during standing operation when AUTO function is on
0 – 1
0: Sewing pauses when presser foot lifter pedal is on (operation pause)
1: Above function is not used
Operation during standing operation when AUTO function is on
0: Operation stops when high speed pedal turns back on, and restarts when
0 – 1
off
1: Above function is not used
Thread trimming pedal function after thread trimming during standing
operation
0 – 1
0: Presser foot can be raised and lowered
1: Above operation not used (only possible using presser foot lifter pedal)
Alternate standing operation pedal and treadle operation (See NOTE 15)
0: Treadle operation is disabled after standing operation pedal is used
0 – 1
1: Treadle operation can also be used after standing operation pedal is used
(alternate operation is possible)
300 – 5000
Automatic deceleration speed when quick reverse mechanism has been
(rpm)
operated using the actuator switch
Correction stitch sewing using actuator switch after thread trimming
0 – 1
0: Not possible (switch operation disabled)
1: Possible
1 – 99
Number of slow start stitches
(needles)
Count units for stitch counter display
0 – 100
0: No counting operation
(needles)
1–100: Display counts down by number of stitches set
Operation when stitch counter warning occurs ("!" icon is illuminated)
0: Starting using treadle is enabled as normal
1: Starting using treadle is disabled (thread trimming by depressing treadle
0 – 2
backward is possible)
2: Starting using treadle is completely disabled once treadle is returned to
neutral and operation stops
Operation after treadle is depressed backward or knee switch is operated
when presser foot is raised
0 – 1
0: When treadle is returned to neutral, presser foot is raised
1: When treadle is returned to neutral, presser foot is lowered
Setting details
S-7200B

Hide quick links:

Advertisement

Table of Contents
loading

Related Manuals for Brother S-7200B

This manual is also suitable for:

Md-741bMd-751bMd-741cMd-751c

Table of Contents