Brother S-7200A Basic Operation Manual
Single needle direct drive straight lock stitcher with thread trimmer
Hide thumbs
Also See for S-7200A:
- Service manual (67 pages) ,
- Instruction manual (47 pages) ,
- Manual (6 pages)
Table of Contents
Advertisement
S-7200A
SINGLE NEEDLE DIRECT DRIVE STRAIGHT LOCK STITCHER WITH THREAD TRIMMER
Please read this manual before using the machine.
4-1. Table processing diagram ......................... 08
4-2. Installation.................................................. 08
4-3. Lubrication (-[]0[], []3[] specifications) ........ 12
4-4. Connecting the cords................................. 13
.................................................... 17
5-1. Installing the needle................................... 17
5-2. Removing the bobbin case ........................ 17
5-3. Winding the lower thread ........................... 18
5-4. Installing the bobbin case .......................... 18
5-5. Threading the upper thread ....................... 19
5-6. Adjusting the stitch length.......................... 19
CONTENTS
......... 01
............ 05
... 06
.................................. 07
Basic Operation Manual
The basic operation manual describes basic operations
including sewing machine operations. For cleaning,
standard adjustments and more details, please refer to the
instruction manual contained in the Document CD.
6-1. Names and functions .................................20
7-1. Names and functions .................................23
....................................................26
8-1. Sewing .......................................................26
8-2. Backtacking................................................26
...............20
...............23
............................................27
Advertisement
Table of Contents
Related Manuals for Brother S-7200A
Summary of Contents for Brother S-7200A
-
Page 1: Table Of Contents
Basic Operation Manual S-7200A SINGLE NEEDLE DIRECT DRIVE STRAIGHT LOCK STITCHER WITH THREAD TRIMMER Please read this manual before using the machine. The basic operation manual describes basic operations including sewing machine operations. For cleaning, standard adjustments and more details, please refer to the instruction manual contained in the Document CD. -
Page 3: Safety Instructions
INSTRUCTIONS 1. SAFETY Thank you very much for buying a BROTHER sewing machine. Before using your new machine, please read the safety instructions below and the explanations given in the instruction manual. With industrial sewing machines, it is normal to carry out work while positioned directly in front of moving parts such as the needle and thread take-up, and consequently there is always a danger of injury that can be caused by these parts. -
Page 4: Notes On Safety
Contact your Brother dealer or a qualified shocks could occur. electrician for any electrical work that may need to be done. - Page 5 When threading the needle power switch. Then contact your nearest Brother When replacing the bobbin and needle dealer or a qualified technician. When not using the machine and when leaving...
-
Page 6: Warning Labels
Please follow the instructions on the labels at all times when using the machine. If the labels have been removed or are difficult to read, please contact your nearest Brother dealer. Be sure to connect the ground. If the ground connection is not... -
Page 7: Convenient Function For Smooth Sewing
(reverse rotation) func- tion together provide 16 mm of space underneath the presser foot. This makes it much easier to insert and remove heavy material without it getting caught on the needle. (Contact the place of purchase.) 3166M 3167M S-7200A... -
Page 8: Names Of Major Parts
Knee lifter assembly Power switch (10) Oil gauge window (-[]0[], []3[] specifications) (11) Reverse lever (12) Stitch length dial (13) Machine pulley (14) Operation panel (Models with operation panel) (15) Cotton stand Safety devices (16) Thread take-up cover (17) Finger guard S-7200A... -
Page 9: Installation
The machine may operate if the treadle is depressed by mistake, which could result in injury. Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. Use both hands to hold the machine head when tilting it back or returning it to its original position. -
Page 10: Table Processing Diagram
Control box mounting hole 2090M 4-2. Installation 1. Control box (1) Control box (2) Bolts [3 pcs] (3) Nuts [3 pcs] (4) Spring washers [3 pcs] (5) Washers [3 pcs] 2. Connecting rod (6) Connecting rod (7) Nut 2091M S-7200A... -
Page 11: Power Switch
(1) Head cushions (left) [2 pcs] (2) Head cushions (right) [2 pcs] (3) Oil pan 2093M 5. Rubber cushions (1) Rubber cushions [2 pcs] (2) Nails [4 pcs] 6. Knee lifter complying bar (3) Knee lifter complying bar 2094M S-7200A... -
Page 12: Machine Head
(1) Sticker 2097M 10. Cotton stand (1) Cotton stand NOTE: Securely tighten the nut (4) so that the two rubber cushions (2) and the washer (3) are securely clamped and so that the cotton stand (1) does not move. 2098M S-7200A... - Page 13 (5) is at the desired position within a distance of 16 mm of the needle plate when the knee liter plate (1) is fully pressed. 9. After adjustment is completed, securely tighten the nut (9). Within 16 mm 2102M S-7200A...
-
Page 14: Lubrication (-[]0[], []3[] Specifications)
Use only the lubricating oil (Nisseki Mitsubishi Sewing Lube 10N; VG10) specified by Brother. * If this type of lubricating oil is difficult to obtain, the recommended oil to use is <Exxon Mobil Essotex SM10;... -
Page 15: Connecting The Cords
CAUTION Contact your Brother dealer or a qualified electrician for any electrical work that may need to be done. Do not connect the power cord until all cords have been connected. The machine may operate if the treadle is depressed by mistake, which could result in injury. - Page 16 (3) using the repeat cable tie (1), otherwise vibration from the sewing machine may cause the cords become disconnected, which can cause problems with the <Securing> operation of the control box. Cords <Closing the cover> 2110M S-7200A...
-
Page 17: Other Cords
AC power supply. NOTE: <Single-phase> <Three-phase> extension cords, otherwise machine operation problems may result. Green and yellow wire (ground wire) 2112M 4. Ground wire Ground symbol (1) Ground wire (2) Screw [With washer] (3) Screw Oil pan 2113M S-7200A... -
Page 18: Test Operation (Operating The Treadle)
(3) is returned to the neutral position (A). (when needle down stopping has been set.) 4. If the treadle (3) is pressed to position (D), thread trimming is carried out and the needle then rises above the needle plate and stops. 2117M S-7200A... -
Page 19: Preparation Before Sewing
There is an anti-spin spring (3) inside the bobbin case. The anti-spin spring (3) prevents the bobbin from racing at times such as during thread trimming. Use bobbins (2) made of light alloy as specified by BROTHER. 2120M For thick materials 0798M 2121M S-7200A... -
Page 20: Winding The Lower Thread
(2), and then pull it out from the thread guide (3). 4. Check that the bobbin turns clockwise when the thread is pulled. 5. Hold the latch (4) on the bobbin case and insert the bobbin case into the rotary hook. 2126M S-7200A... -
Page 21: Threading The Upper Thread
(3) is pushed to the halfway- down position. 3. Push the dial lock lever (1) down firmly to lock it. * Check that the stitch length dial (2) does not rotate. 2128M S-7200A... -
Page 22: Using The Operation Panel (Basic Operations)
When this key is pressed so that the indicator illuminates, the number of backtack stitches (0−99) in the A, B, C and D stitch number displays is sewn continuously. After the sewing machine sews a full cycle of stitches set by A, B, C and D, the thread is trimmed automatically. 2142M S-7200A... - Page 23 These keys are used to set the initial value for the lower thread counter. (Refer to p.23.) 2155M (17) RESET key This key is used to return the lower thread counter to its initial value and to cancel warning conditions. (Refer to p.23.) 2156M S-7200A...
-
Page 24: Sewing Start And End Backtack Stitches
• If the indicator of the thread trimming lock key is illuminated, the sewing machine will stop in the needle up position without thread trimming being carried out. 2160M S-7200A... -
Page 25: Using The Control Box Panel (Basic Operations)
C and D (0–9) are sewn. Stitch number display • This shows the backtacking processes (A, B, C and D) and the number of stitches for each. NOTE: This is only displayed when making the settings. • It also displays error codes. S-7200A... -
Page 26: Sewing Start And End Backtack Stitches
1. Press the start backtack key (1) so that "d" is displayed. 2. Press the end backtack key (3) to set the number of stitches for d. (Example: 6) 3139M Press the power switch (2) to turn off the power. 3140M S-7200A... - Page 27 End backtacking is carried out. After it has finished, the thread is trimmed automatically and the sewing machine stops in the needle up position. NOTE: If the treadle is depressed backward before sewing of the set number of start backtack stitches is complete, end backtacking will not be carried out. 2160M S-7200A...
-
Page 28: Sewing
3. Depress the treadle to start sewing. 2114M 2115M 8-2. Backtacking When the actuator (1) or the reverse lever (2) is pressed 2175M during sewing, the feed direction will be reversed. When it is released, the feed direction will return to normal. 2176M S-7200A... -
Page 29: Document Cd
Adobe, the Adobe logo, and Reader are either registered trademarks or trademarks of Adobe Systems Incorporated in the United States and/ or other countries. Windows® and Microsoft® Internet Explorer are either registered trademarks of Microsoft Corporation in the United States and/ or other countries. http://www.brother.com/ © 2004 Brother Industries, Ltd. All Rights Reserved. S-7200A SA5275-001 E 2004.10.B(1)
Need help?
Do you have a question about the S-7200A and is the answer not in the manual?
Questions and answers