Dell PowerVault TL2000 User Manual page 278

K
Key Path 5-38
Key Path Diagnostics 5-61
keyboard H-1
L
Labels
bar code 6-4
guidelines for using 6-5
LED, amber 7-12
LEDs 2-2, 7-7
LEDs, front panel 1-1
library configuration form G-1
library firmware, current level 5-34
library logs 5-58
library mode 4-19, 5-20, 5-34, 5-44
library name 5-44
library network configuration 4-24, 5-50
library recovery 7-6
library SNMP configuration 4-29, 5-56
library status 5-37
Library Verify 5-30
library weight 1-11
license activation key 4-21, 4-22, 5-29
Link-local IPv6 address 5-10
Linux D-1, D-2
LME 5-47
locating the library 4-1
logical libraries 4-21, 5-18, 5-45
determining number 3-1
basic guidelines 3-1
using multiple for sharing 3-2
logical libraries, assigning 4-21
logs 5-58
low voltage differential (LVD) SCSI
interface 1-8
low-power mode 1-10
LUN 3-6, D-1, D-2
LUN scanning 3-6
LVD SCSI interface 1-8
M
MAC Address 1-7
magazines 1-1, 4-32
Maximum Transmission Unit (MTU) 1-7
media 1-10
Media 6-1
media capacity 1-1
menu shortcuts 5-1
menu tree
Operator Control Panel 5-9
Menus
Configure
network settings 4-15
MIB 1-7, B-1
Monitor menu
Drive 5-12
Library 5-10
Move Media 4-36, 5-16, 5-42
Multiple control paths 3-2
X-2
Dell PowerVault TL2000 Tape Library and TL4000 Tape Library User's Guide
N
Navigation 5-7
Netmask 4-15
Network Address Translation (NAT) 1-7
network configuration 5-24
Network Mask 4-24, 5-24, 5-50
network settings 5-24
O
OCP 4-31
ON/OFF power button 2-4
operation specifications 1-11
Operator Control Panel
Access PIN 5-26
Configure: Save/Restore 5-27
control keys on front panel 1-1
display 1-1
menu tree 5-9
Monitor menu
Drive 5-12
Library 5-10
power ON display 2-2
Operator Control Panel menus
Configure: Drive 5-23
Configure: Library 5-20
P
packaging materials 4-2
partitioning 3-3, 4-21, A-3
partitioning your 4U library 5-45
path failover 4-21, 5-29
physical specifications 1-11
power button 1-1, 2-4
power connector 1-3
power management 1-10
power ON display 2-2
power source 4-1
power specifications 1-11
Power Supply Problem 7-7
product ID 5-34
PTF 7-12
Q
Quiesce 5-61
R
rack installation 4-1, 4-5
rack mounting the library 4-5
rack requirements 4-1
RAID controllers 3-6
Read/Write capability 6-2
rear panel of library 1-3
Remove/replace procedures 10-1
reserve slot, active slot 5-65
Reserved Slots 4-19
RFC (Request for Comments) 1-7
Router assigned IPv6 address 5-10
S
Safety inspection procedure xiv
SAS interface 3-9
screens displayed at power ON 2-2
SCSI interface 3-7
bus termination 3-9
description 1-8
multiple buses 3-8
physical characteristics 3-7
SCSI LVD 3-7, 3-9
SCSI Trade Association Web site 3-9
Sense data
using C-1
sense data, library C-1
sequential mode, starting 5-20
sequential mode, stopping 5-20
serial number 5-34
serial number, drive 5-35
Serial Port 1-3
server attachment
SCSI interface 3-7
Sharing the library 3-1
shipment verification 4-2
shipping container 4-2
shipping label, removing and
storing 4-4
shipping lock and label storage
location 1-3
shipping lock. removing and storing 4-4
shortcut keys H-1
Simple Network Management
Protocol 1-7
sled, description of tape drive 1-8
slot physical locations A-2
SME 5-47
SNMP 1-7, 4-29, 5-50, 5-56, B-1, F-1
specifications 1-11
environmental 1-11
operation 1-11
physical 1-11
power 1-11
Specifications
cartridges 6-9
speed matching 1-10
SSL 4-24, 5-50
storage capacity 1-8
T
tape cartridge 1-10
tape drive sled 1-3
Tape drives
channel calibration 1-10
power management 1-10
quantity in library 1-8
speed matching 1-10
TapeAlert Flags
for drives B-2
TapeAlert Flags, library B-1
Telnet Service Port 5-33
Traps F-1
troubleshooting 7-1