FMS FCX10 Instruction Manual page 22

System Functions
数据复位
Data Reset
This function is used to restore the end point value set to the default value.
Setup:
To restore to the default value, press the BIND and CH4 buttons of the transmitter at the same time, and power the
transmitter on. At this time, the buzzer will give a long beep.
Note: This function is only applicable to resetting the end point value set to the default value.
此功能用于将设置的舵量数值恢复为默认值。
功能设置：
同时按住对码按键（BIND）和 CH4 按键后，并通电开机，即恢复成默认值，蜂鸣器长响一声提示。
注：此功能仅适用于复位舵量至默认值。
Function Instructions
注意事项
Attention
• Make sure the product is installed and calibrated correctly, failure to do so may result in serious injury.
• Please carefully check each power device and car frame instructions to ensure the power matching is reasonable
before use. Avoid damaging power system due to incorrect matching.
• Do not let the external temperature of the system exceed 90℃ /194 ℉ , because high temperature will damage the
power system.
• Make sure the receiver's battery is disconnected before turning off the transmitter, failure to do so can result out of
control. Unreasonable setting of the Failsafe may cause accidents.
• After use, remember to disconnect the battery and the ESC. If the battery isn't disconnected, the ESC will consume
electric energy all the time even if it is off. It will discharge completely if connect the battery for a long time, thus
resulting in the failure of the battery or the ESC. We are not responsible for any damage caused by this!
• Make sure the receiver is mounted away from motors or any device that emits excessive electrical noise.
• Keep the receiver's antenna at least 1cm away from conductive materials such as carbon or metal.
• Do not power on the receiver during the setup process to prevent loss of control.
• If the throttle trim is changed on the transmitter side, the receiver needs to be re-powered to recognize the new
throttle neutral. Otherwise, an exception may occur during RC car reversing.
• 使用前必须确保本产品与模型安装正确，否则可能导致模型发生严重损坏。
• 请查看各动力设备以及车架说明书，确保动力搭配合理，避免因错误的搭配导致动力系统损坏。
• 勿使系统的外部温度超过 90℃ /194 ℉，高温将会毁坏动力系统。
• 关闭时，请务必先关闭接收机电源，然后关闭发射机。如果关闭发射机电源时接收机仍然在工作，将导致遥控设备失
控。失控保护设置不合理可能引起事故。
• 使用完毕后，若长时间不玩车，切记断开电池与电调的连接。如电池未断开，即使电调开关处于关闭状态，电调也会一直消耗电能
（只是非常小），长时间连接电池最终会被过放，进而导致电池或电调出现故障。我们不对因此而造成的任何损害负责！
• 确保接收机安装在远离电机或电子噪声过多的区域。
• 接收机天线需远离导电材料，例如金属棒和碳物质。为了避免影响正常工作，请确保接收机天线和导电材料之间至少有 1 厘米以上
的距离。
• 准备过程中，请勿连接接收机电源，避免造成不必要的损失。
• 若在发射机端调整油门通道微调后，接收机须重新通电以识别新的油门通道中位，否则可能会出现倒车异常的现象。
系统功能
功能说明
21