FMS FCX10 Instruction Manual page 21

System Functions
失控保护
Failsafe
The failsafe function is used to protect the model and personnel when the receiver is out-of-control.
The failsafe of CH2 is enabled by default, and the ESC will enter the braking status after out-of-control. The other
channels of the receiver (CH1, CH2, CH4 and CH6) are not set by default, and will keep the last output after out-of-
control. If other channels have been set on the transmitter side, they will be output according to the set value; at the
same time, the turn signal right Light and turn signal left light will flash slowly and synchronously.
For the other channels, it can be set at the transmitter side. The setting steps are as below.
• In the normal power-on status, set the control corresponding to the channel to be configured with failsafe to the
preset position, meanwhile, press and hold the BIND button for 3 seconds to set the output value as the failsafe
value. And the buzzer will give a long beep indicating that the setting is successful.
Note: Restore to the default setting in case of re-binding.
此功能用于当接收机无法正常收到发射机的信号不受控制时，保护模型和操作人员的安全。
CH2 失控保护默认开启，失控后电调进入刹车状态。接收机其他通道（CH1、CH2、CH4 和 CH6 通道）默认未设置 , 失控后保持
最后输出。若其他通道已在发射机端设置，则按照设置值输出；同时左、右车灯同步慢闪提示。
可在发射机端设置其他通道相应的失控保护值，设置步骤如下：
• 开机正常状态下，先操作需要设置失控保护的通道所对应的控件至预设的位置，再长按对码按键（BIND） 3 秒，即将当下输出的
通道值设置为该通道失控保护值。设置成功时，蜂鸣器长响一声提示。
注：重新对码时恢复默认设置。
闲置报警
Idle Alarm
The transmitter will go into idle alarm state when there is no operation over 10 minutes.
When the transmitter is in idle alarm state, the G.LED will be in gradual light state, and the buzzer will prompt with beep-
ing twice cyclically. Operate steering wheel or throttle trigger to cancel the idle alarm.
当发射机未操作时间大于 10 分钟时，即进入闲置报警状态。
在此状态下，发射机 G.LED 指示灯为呼吸灯状态且蜂鸣器响 3 声循环提示。闲置报警状态下，操作发射机的手轮或扳机可退出闲置
报警状态。
休眠模式
Sleep Mode
When the transmitter has been in idle alarm state over 2 minutes, it will enter the sleep mode.
In this mode, the G.LED will be in gradual light status, other indicators will be off, and the buzzer and RF will turn off.
To exit the sleep mode, power off the transmitter and restart it.
当发射机处于闲置报警状态时间大于 2 分钟时，即进入休眠模式。
在此模式下，发射机 G.LED 指示灯为呼吸灯状态提示，其他指示灯灭，蜂鸣器关闭，RF 关闭。
须重启发射机才可退出休眠模式。
Transmitter Voltage Alarm
When the system detects a low voltage, it will give an alarm. Avoid accidents caused by long-term operation under low
voltage.
When the voltage is detected below 4.2V/7.0V (AA battery/LiPo battery), there is an alarm due to low voltage. At this
time, the G.LED will flash slowly, and the buzzer prompts with beeping once cyclically.
When the voltage is detected below 3.5V (ultra-low), the transmitting function is disabled. The G.LED will be in gradual
light state.
当系统检测到低电压时，即发出报警。避免控制系统在低电压状态下长时间运行造成意外。
当检测到电压低于 4.2V/7.0V（AA 电池 /LiPo 电池），即进入低电报警状态，此时 G.LED 指示灯慢闪状态，蜂鸣器响 1声循环提示。
当检测到电压超低时（低于 3.5V 时），发射功能关闭，G.LED 指示灯为呼吸灯状态提示。
系统功能
发射机电压报警
20