Adjusting The Keyboard Touch Response (Key Touch Edit); Restore The Settings To Initial Conditions (Initialize) - Roland RD-700GX Owner's Manual

WURLY
This combines REED EP with a variation of it, reproducing a
typical E. piano sound of the '60s.
Parameter Value
Treble -50–+50
Bass -50–+50
Vibrato Sw OFF/ON
Vibrato Rate
Hz/
Mode
Vibrato Rate
0.05–10.00Hz
(Hz)
Vibrato Rate
(*1)
( )
Vibrato Depth 0–127
LINE, OLD,
Speaker Sim NEW, WURLY,
TWIN
Level 0–127
STAGE TWIN
This simulates playing through a guitar amp.
Parameter Value
Treble -50–+50
Bass -50–+50
Tremolo Sw OFF/ON
Tremolo Rate
Hz/
Mode
Tremolo Rate
0.05–10.00Hz
(Hz)
Tremolo Rate
(*1)
( )
Tremolo Depth 0–127
Tremolo Duty -10–+10
LINE, OLD,
Speaker Sim NEW, WURLY,
TWIN
Level 0–127
note :
(*1)
fig.MFX-note2e
(Sixty-fourth-note triplet), (Sixty-fourth note),
(Thirty-second note), (Sixteenth-note triplet),
(Sixteenth note), (Eighth-note triplet),
(Eighth note), (Quarter-note triplet),
(Quarter note), (Half-note triplet),
(Whole-note triplet), (Dotted half note),
(Dotted whole note),
(Double-note triplet),
Description
Amount of boost/cut for the high-
frequency range
Amount of boost/cut for the low-
frequency range
Turns tremolo on/off.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the tremolo (Hz)
Frequency of the tremolo (note)
Depth of the effect
Type of the speaker
* When "LINE" is selected, no
speaker used.
Adjust the output level.
Description
Amount of boost/cut for the high-
frequency range
Amount of boost/cut for the low-
frequency range
Turns tremolo on/off.
When this is set to "note," the effect is
synchronized with the tempo.
Frequency of the tremolo (Hz)
Frequency of the tremolo (note)
Depth of the tremolo
Specifies the duty cycle of the LFO
waveform used to apply tremolo.
Increasing this value will increase the
duty cycle of the LFO waveform for the
L-channel; the duty cycle for the R-
channel will decrease.
Type of the speaker
* When "LINE" is selected, no
speaker used.
Adjust the output level.
(Thirty-second-note triplet),
(Dotted thirty-second note),
(Dotted sixteenth note),
(Dotted eighth note),
(Dotted quarter note), (Half note),
(Whole note),
(Double note)
Making Detailed Settings for the ONE TOUCH Tones
Adjusting the Keyboard Touch
Response (Key Touch Edit)
You can adjust the way in which the keyboard responds to
your playing touch.
→ "Changing the Key Touch (Key Touch)" (p. 79)
→ "Making Fine Adjustments to the Keyboard Touch (Key
Touch Offset)" (p. 79)
→ "Setting a Constant Volume Level in Response to the Playing
Force (Velocity)" (p. 80)
→ "Changing the Timing of Sounds in Response to the
Velocity (Velocity Delay Sensitivity)" (p. 80)
→ "Changing the Touch Sensitivity According to the Key
Range (Velocity Keyfollow Sensitivity)" (p. 80)
→ "Changing How Volume Responds to Your Dynamics (Key
Touch Mode)" (p. 80)
Restore the settings to initial conditions
(Initialize)
This restores the One Touch E. Piano settings to their initial
conditions.
1.
In Step 3 of the E. Piano Designer settings
instructions (p. 82), select "2. Initialize" and
press the [ENTER] button.
The Initialize Screen appears.
To cancel the Initialize, press the [EXIT/SHIFT] button.
2.
Press the [ENTER] button.
The confirmation message appears.
To cancel the procedure, press the [EXIT/SHIFT] button.
3.
Press the [ENTER] button once again.
The ONE TOUCH [E. PIANO] button's tones are
initialized.
87