Roland RD-700GX Owner's Manual page 184

Effect/Parameter List
118:*ENH→DELAY
(ENHANCER→ DELAY)
This effect connects an enhancer and a delay in series.
MFX Control Delay Bal, Enhancer Sens
Parameter Value
Enhancer Sens 0–127
Enhancer Mix 0–127
Delay Time 0.1–500.0 ms
Delay Feedback -98– +98%
200–8000 Hz,
Delay HF Damp
BYPASS
D100:0W–
Delay Bal
D0:100W
Level 0–127
119: *CHO→DELAY (CHORUS→DELAY)
This effect connects a chorus and a delay unit in series.
MFX Control Chorus Bal, Delay Bal
Parameter Value
Chorus PreDly 0.0–100.0 ms
Chorus Rate 0.05–10.00 Hz
Chorus Depth 0–127
D100:0W–
Chorus Bal
D0:100W
Delay Time 0.1–500.0 ms
Delay Feedback -98– +98%
200–8000 Hz,
Delay HF Damp
BYPASS
184
Assignable Parameters
Description
Adjust the sensitivity of the enhancer.
Adjust the ratio with which the
overtones generated by the enhancer
are combined with the direct sound.
Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Adjust the proportion (%) of the delay
sound that is fed back into the delay
input. Negative (-) settings will invert
the phase.
Adjust the frequency above which
delayed sound fed back to the delay
input will be cut. If you do not want to
cut the high frequencies of the delay
feedback, set this parameter to
BYPASS.
Adjust the volume balance between
the enhancer sound that is sent
through the delay and the enhancer
sound that is not sent through the
delay. With a setting of "D100:0W,"
only the enhancer sound will be
output. With a setting of "D0:100W,"
only the enhancer sound that is sent
through the delay will be output.
Adjust the output level.
Assignable Parameters
Description
Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Adjust the modulation speed of the
chorus effect.
Adjust the modulation depth of the
chorus effect.
Adjust the volume balance between
the direct sound and the chorus sound.
With a setting of "D100:0W," only
the direct sound will be output. With a
setting of "D0:100W," only the
chorus sound will be output.
Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Adjust the proportion (%) of the delay
sound that is fed back into the delay
input. Negative (-) settings will invert
the phase.
Adjust the frequency above which
delayed sound fed back to the delay
input will be cut. If you do not want to
cut the high frequencies of the
feedback, set this parameter to
BYPASS.
Parameter Value
D100:0W–
Delay Bal
D0:100W
Level 0–127
120:*FLANGR→DLY (FLANGER→DELAY)
This effect connects a flanger and a delay in series.
MFX Control Flngr Bal, Delay Bal
Parameter Value
Flngr PreDly 0.0–100.0 ms
Flngr Rate 0.05–10.00 Hz
Flngr Depth 0–127
Flngr Fbk -98– +98%
D100:0W–
Flngr Bal
D0:100W
Delay Time 0.1–500.0 ms
Delay Feedback -98– +98%
200–8000 Hz,
Delay HF Damp
BYPASS
D100:0W–
Delay Bal
D0:100W
Level 0–127
121: *CHO→FLANGR
(CHORUS→ FLANGER)
This effect connects a chorus and a flanger in series.
MFX Control Chorus Bal, Flngr Bal, Chorus Rate, Flngr Rate
Parameter Value
Chorus PreDly 0.0–100.0 ms
Chorus Rate 0.05–10.00 Hz
Description
Adjust the volume balance between
the chorus sound that is sent through
the delay and the chorus sound that is
not sent through the delay. With a
setting of "D100:0W," only the
chorus sound will be output. With a
setting of "D0:100W," only the
chorus sound that is sent through the
delay will be output.
Adjust the output level.
Assignable Parameters
Description
Adjust the time delay from when the
direct sound begins until the flanger
sound is heard.
Adjust the modulation speed of the
flanger effect.
Adjust the modulation depth of the
flanger effect.
Adjust the proportion (%) of the
flanger sound that is fed back into the
effect. Negative (-) settings will invert
the phase.
Adjust the volume balance between
the direct sound and the flanger
sound. With a setting of "D100:0W,"
only the direct sound will be output.
With a setting of "D0:100W," only
the flanger sound will be output.
Adjust the time delay from when the
direct sound begins until the delay
sound is heard.
Adjust the proportion (%) of the delay
sound that is fed back into the delay
input. Negative (-) settings will invert
the phase.
Adjust the frequency above which
delayed sound fed back to the delay
input will be cut. If you do not want to
cut the high frequencies of the delay
feedback, set this parameter to
BYPASS.
Adjust the volume balance between
the flanger sound that is sent through
the delay and the flanger sound that is
not sent through the delay. With a
setting of "D100:0W," only the
flanger sound will be output. With a
setting of "D0:100W," only the
flanger sound that is sent through the
delay will be output.
Adjust the output level.
Assignable Parameters
Description
Adjust the time delay from when the
direct sound begins until the chorus
sound is heard.
Adjust the modulation speed of the
chorus effect.