Roland RD-700GX Owner's Manual page 180

Effect/Parameter List
Parameter Value
200–8000 Hz,
HF Damp
BYPASS
Rate 0.05–10.00 Hz
Depth 0–127
Phase 0–180 degree
Low Gain -15– +15 dB
High Gain -15– +15 dB
D100:0W–
Balance
D0:100W
Level 0–127
103: *TRIPLE DLY (TRIPLE TAP DELAY)
The Triple Tap Delay produces three delay sounds; center, left
and right.
MFX Control Balance
Parameter Value
200–1000 ms,
Dly Left
note (*2)
200–1000 ms,
Dly Right
note (*2)
200–1000 ms,
Dly Center
note (*2)
Feedback -98– +98%
200–8000 Hz,
HF Damp
BYPASS
Left Level 0–127
Right Level 0–127
Center Level 0–127
Low Gain -15– +15 dB
High Gain -15– +15 dB
D100:0W–
Balance
D0:100W
Level 0–127
180
Description
Adjust the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Adjust the speed of the modulation.
Adjust the depth of the modulation.
Adjust the spatial spread of the sound.
Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Adjust the volume balance between
the direct sound and the modulation
delay sound. With a setting of
D100:0W only the direct sound will
be output, and with a setting of
D0:100W only the modulation delay
sound will be output.
Adjust the output level.
Assignable Parameters
Description
Adjust the time delay from the direct
sound until when the left delay sound
is heard.
Adjust the time delay from the direct
sound until when the right delay sound
is heard.
Adjust the time delay from the direct
sound until when the center delay
sound is heard.
Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjust the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Adjust the volume of the left delay
sound.
Adjust the volume of the right delay
sound.
Adjust the volume of the center delay
sound.
Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Adjust the volume balance between
the direct sound and the delay sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the delay
sound will be output.
Adjust the output level.
Delay C, Delay L and Delay R parameters can be set as a
note-value of a tempo. In this case, specify the value of the
desired note.
104:*QUAD.DELAY
(QUADRUPLE TAP DELAY)
The Quadruple Tap Delay has four delays.
The stereo location of each delay sound is as follows.
MFX Control Balance
Parameter Value
200–1000 ms,
Dly1 Time
note
200–1000 ms,
Dly2 Time
note
200–1000 ms,
Dly3 Time
note
200–1000 ms,
Dly4 Time
note
Level 1 0–127
Level 2 0–127
Level 3 0–127
Level 4 0–127
Feedback -98– +98%
200–8000 Hz,
HF Damp
BYPASS
D100:0W–
Balance
D0:100W
Level 0–127
Delay 1–4 parameters can be set as a note-value of a tempo.
In this case, specify the value of the desired note.
105: *T-CTRL DLY
(TIME CONTROL DELAY)
When the Effects MFX Control setting in Edit mode set to
"Delay," you can use MULTI EFFECTS [CONTROL] knob to
make changes in the delay time and pitch in real time.
Lengthening the delay will lower the pitch, and shortening it
will raise the pitch.
MFX Control Delay, Balance
Parameter Value
Delay 200–1000 ms
Feedback -98– +98%
Assignable Parameters
Description
Adjust the time delay from the direct
sound until when delay 1 sound is
heard.
Adjust the time delay from the direct
sound until when delay 2 sound is
heard.
Adjust the time delay from the direct
sound until when delay 3 sound is
heard.
Adjust the time delay from the direct
sound until when delay 4 sound is
heard.
Adjust the volume of delay 1 sound.
Adjust the volume of delay 2 sound.
Adjust the volume of delay 3 sound.
Adjust the volume of delay 4 sound.
Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Adjust the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies of the feedback, set this
parameter to BYPASS.
Adjust the volume balance between
the direct sound and the delay sound.
With a setting of D100:0W only the
direct sound will be output, and with a
setting of D0:100W only the delay
sound will be output.
Adjust the output level.
Assignable Parameters
Description
Adjust the time delay from the direct
sound until when each delay sound is
heard.
Adjust the proportion (%) of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.