Table of Contents
Advertisement
UG-248
EVALUATION BOARD SOFTWARE QUICK START PROCEDURES
SSM2380
CONTROL SOFTWARE SETUP
Do not connect the evaluation board until software is installed.
The
SSM2380
software interface requires Microsoft® .NET
Framework (Version 2.0 or later). The installer automatically
downloads it if .NET Version 2.0 is not already installed.
To install the control software, use the following steps:
1.
Go to www.analog.com/SSM2380.
2.
Click Evaluation Boards & Kits.
3.
Choose the appropriate Windows version (32-bit or 64-bit)
to download.
4.
Extract the
SSM2380
zipped installation file to a
convenient location and double-click setup.exe to begin
the installation process. Follow the installation instructions
when prompted.
5.
The software and USB drivers are installed in C:\Program
Files\Analog Devices Inc\SSM2380.
SSM2380
USB Driver Installation
Before connecting the
SSM2380
notebook, the following procedure may need to be completed.
(This procedure only needs to be executed once on each com-
puter that uses the
SSM2380
skipped if the user has previously installed any SigmaStudio
or USBi related drivers from Analog Devices, Inc.)
1.
Exit the
SSM2380
user interface software.
2.
Remove jumpers from JP1, JP2, and JP3, located at the top
of the evaluation board to completely isolate the Cypress
USB driver from the SSM2380.
3.
Connect JP4 in the 3.3 V location as shown in the blue-
circled area of Figure 4. The purpose of this is to power
the Cypress USB controller to establish communication
between the software and the board.
4.
Make sure the software was closed. Connect the
evaluation board to the PC via the USB cable.
5.
The PC recognizes the new hardware. When the hardware
is recognized, a prompt asks to let Windows find the
proper drivers for the hardware.
Do not let Windows install the drivers.
6.
The user must direct the driver installation to the following
path by clicking the Browse tab:
C:\Program Files\Analog Devices Inc\SSM2380\
7.
After the path has been properly selected, the user can
continue with the driver installation process. Windows
will properly establish the link between the Cypress USB
controller and the PC.
evaluation board to a PC or
software. This procedure can be
SSM2380
8.
After the previous steps are followed, the user can now run
the
SSM2380
the following path: C:\Program Files\Analog Devices
Inc\SSM2380\ SSM2380.exe.
9.
For quick access to this software, the installer creates a
shortcut from the SSM2380.exe file to the desktop.
10. If all steps were properly followed, at the top of the
SSM2380
software window, a status message of USBi
Connected appears. If the installation was not successful,
a message of USBi – Cannot Find Device appears.
11. After a successful installation, the
recognizes a connection from the PC to the
evaluation board. There is no need to adjust the jumper
positions of JP1, JP2, and JP3; but they should be
connected as shown in Figure 4.
Uninstall
SSM2380
1.
Locate the directory where the
file was extracted.
2.
Double-click setup.exe. Simply select Uninstall to remove
the software from the host PC.
INITIAL
SSM2380
To allow the
SSM2380
evaluation board, the user must make a few simple jumper
connections:
1.
Connect the bottom and middle terminals of each jumper
JP1, JP2, and JP3. The purpose of this is to connect the
on-board Cypress USB-I
signals connected are I
2.
Connect JP4 in one of two positions to choose an I
supply rail, either 1.8 V or 3.3 V. These two voltages
come from separate on-board LDOs. The
control interface works well under either of these I
supply voltage conditions.
Rev. 0 | Page 6 of 20
Evaluation Board User Guide
control software. The software is located at
SSM2380
Control Software
SSM2380
zipped installer
HARDWARE SETUP
software to control the
2
C interface to the SSM2380. The
2
C VDD, I
2
C CLK, and I
software
SSM2380
SSM2380
2
C DATA.
2
C
SSM2380
2
C
Advertisement
Table of Contents
Need help?
Do you have a question about the SSM2380 and is the answer not in the manual?
Questions and answers