Evaluation Board Hardware; Power Supplies; Input Signals; Output Signals - Analog Devices SSM2380 User Manual

Evaluation Board User Guide

EVALUATION BOARD HARDWARE

The SSM2380 evaluation board provides all of the support
circuitry required to operate the
a computer interface for the I
bench characterization setup used to evaluate the audio perfor-
mance of the SSM2380. See the Evaluation Board Software
Quick Start Procedures section to get started.
TO LOAD
1/8" STEREO
INPUT
OR
DIFERENTIAL
AUDIO INPUT
TO ANALYZER
Figure 2. Diagram View of Evaluation Board Connections

POWER SUPPLIES

The SSM2380 requires an external dc power supply. A 2-pin
0.100" male header, H3, is provided on the evaluation board.
Supply voltages between 2.5 V and 5.5 V are accepted, and
supply currents may exceed 1 A under some conditions.
Alternatively, 5 V USB power supply can be used to power the
chip, although the USB 2.0 specification only allows current
draw up to 500 mA. Be cautious when using the USB port
to supply any significant amount of power. The jumper
configuration used for USB power is shown in Figure 3.
Be sure to remove JP7 when using an external power supply,
as this will short the I C voltage to the external supply.
2
Conversely, be sure to remove the external supply from
H3 when using USB power.
Figure 3. Connecting USB Power Supply to
SSM2380 amplifier, including
2 C bus. Figure 2 shows the typical
2
EXTERNAL I C
2.5V TO 5.5V
TO PC
SSM2380

INPUT SIGNALS

On the left side of the PCB are two 4-pin headers, JP5 and JP6.
These are used to connect the input audio signal to the amplifier. If
the input audio signal is differential, use the two center pins of
JP5 (INL+ and INL−) for left channel audio and the two center
pins of JP6 (INR+ and INR−) for the right channel audio. In
this case, connect either the top or the bottom pin to the source/
signal ground.
For single-ended audio inputs, only two pins of JP5 and two
pins of JP6 are used: ground and the input signal. If a non-
inverting input is desired, connect the input signals to INL+
and INR+, and place jumpers between Pin 3 and Pin 4 of JP5
and JP6, shorting INL− and INR− to ground.
Conversely, if an inverting input is desired, connect the input
signals to INL− and INR−, and place the jumpers between Pin 1
and Pin 2 of JP5 and JP6, shorting INL+ and INR+ to ground.
Alternatively, single-ended stereo audio can be supplied by
connecting a standard ⅛" stereo plug to the J2 input. In this
case, jumpers must connect INL− and INR− to ground.

OUTPUT SIGNALS

Each channel of the amplifier output is available at two 2-pin
0.100" headers. The speakers are connected in bridge-tied load
(BTL) configuration, and the output pins are labeled with their
polarity; for example, OUTL+ indicates the left channel nonin-
verting terminal.
In the standard filterless configuration, the two headers on
each channel are connected with 0 Ω links on the pads marked
B1 to B4. In this case, the two headers on each channel are tied
together and can be used interchangeably as attachment points
for the load and an audio analyzer. The EMI filtering is not
populated on the
measurement of key parameters such as SNR and THD.
The top layer of the PCB contains the footprints necessary for a
ferrite bead-based EMI filter configuration, whereas the bottom
layer of the PCB contains the footprints for an inductor-based
EMI filter. If EMI filtering is used, only H6 and H7 connect at
the proper location with respect to the filter components—the
load must be connected to these headers. Measurements of the
unfiltered waveform can be taken at H4 and H5.

SHUTDOWN AND MODE JUMPERS

The 2-pin jumper, JP8, is used to enable and disable the
amplifier. Inserting a jumper across JP8 pulls the SD pin to the
SPKVDD supply rail, activating the amplifier. Removing the
jumper from JP8 shuts down both channels of the
so that minimal current (about 20 nA) is drawn from the
power supply.
Rev. 0 | Page 3 of 20
SSM2380 evaluation board to allow proper
UG-248
SSM2380
SSM2380