Specifications; General Specifications - Yamaha PM 5000 Owner's Manual

Appendix
Specifications
1. General Specifications
0dBu is referenced to 0.775 Vrms.
Total Harmonic Distortion
(Master Output)
Frequency Response
(Master Output)
Hum & Noise (20Hz-20kHz) *1
Rs=150Ω
Input Gain=Maximum
Input Pad =OFF
Input sensitivity=-60dBu
Maximum Voltage Gain *2
Crosstalk
MONO & ST INPUT PAD
MONO & ST INPUT GAIN
INPUT High Pass Filter
INPUT Equalization *3
HIGH
HI-MID
LO-MID
LOW
Sweep sine wave oscillator/Pink noise with burst
Phantom Power
Input LED Meter
Output LED Meter
96
Less than 0.1% 20Hz-20kHz @ +14dBu 600Ω
(THD+N) (Input Gain Control at Maximum)
0+1,-3dB 20Hz-20kHz @ +4dBu 600Ω
(Input Gain Control at Maximum)
-128dBu Equivalent Input Noise.
-100dBu Residual Output Noise.
-92dBu (96dB S/N) STEREO AUX Master fader at nominal level and all assign SW's off.
-87dBu (91dB S/N) GROUP/AUX Master fader at nominal level and all assign SW's off.
-92dBu (96dB S/N) STEREO, MONO (C) Master fader at nominal level and all assign SW's off.
-64dBu (68dB S/N) STEREO AUX, GROUP/AUX, STEREO, MONO (C) Master fader and one input fader at nominal level.
-89dBu(93dB S/N) MATRIX Master at nominal level and all Matrix mix controls at minimum level.
64dB MONO IN to MONO IN INSERT OUT,DIRECT OUT (pre fader)
80dB MONO IN to STEREO AUX OUT (PRE),GROUP/AUX OUT (AUX mode & PRE)
90dB MONO IN to STEREO AUX OUT (POST),GROUP/AUX OUT (AUX mode & POST)
84dB MONO IN to GROUP/AUX OUT (GROUP mode), STEREO OUT(INPUT to ST),
MONO (C) OUT (INPUT to MONO)
90dB MONO IN to MATRIX OUT (GROUP/AUX MASTER GROUP mode to MATRIX)
64dB ST IN to ST INSERT OUT
80dB ST IN to STEREO AUX OUT (PRE)
90dB ST IN to STEREO AUX OUT (POST)
84dB ST IN to GROUP/AUX OUT (GROUP mode), STEREO OUT (INPUT to ST)
81dB ST IN to MONO (C) OUT (INPUT to MONO)
77dB ST IN to GROUP/AUX OUT (AUX mode & PRE)
87dB ST IN to GROUP/AUX OUT (AUX mode & POST)
10dB SUB IN to Master OUT
6dB 2TR IN to MONITOR OUT
-80dB @ 1kHz, -70dB @ 10kHz Adjacent inputs.
-80dB @ 1kHz, -70dB @ 10kHz input to output.(except between L and R)
26dB
50dB Variable
12dB/octave roll off below 20-400Hz at -3dB points.
+15, -15dB maximum
1k-20kHz (peaking/shelving, Q=0.5-3)
0.4k-8kHz (peaking, Q=0.5-3)
80-1.6kHz (peaking, Q=0.5-3)
30-600Hz (peaking/shelving, Q=0.5-3)
4 mode selectable (100Hz/1kHz/10kHz/PINK)
Selectable FIX or SWEEP for 100Hz/1kHz/10kHz by SWEEP/BURST ON/OFF switch, sweep
range: x0.2-x2, Less than 1% T.H.D. @ +4dBu
Selectable continue or BURST for PINK noise by SWEEP/BURST ON/OFF switch.
PINK NOISE: fixed 200msec, INTERVAL: variable 1sec-20sec
+48VDC is applied to balanced inputs for powering condenser microphones via 6.8kΩ current-
limiting/isolation resistors.
9-points (PEAK/+12/+6/+3/0/-3/-6/-12/-25dB) LED level meter built into each MONO-IN and ST-
IN module.
PEAK LED (red) turns on when pre-EQ level or post-EQ level or pre-Fader level reaches 3dB below
clipping.
+12/+6/+3/0 LED (yellow) turns on when pre-Fader level reaches +12/+6/+3/0dB.
-3/-6/-12/-25 LED (green) turns on when pre-Fader level reaches -3/-6/-12/-25dB.
20-points (PEAK, +15, <3dB step>, -39dB) LED level meter.
STEREO AUX 1 (L, R)-12 (L, R), STEREO MATRIX 1 (L, R)-4 (L, R)
(STEREO AUX/STEREO MATRIX selectable)
GROUP/AUX 1-8, MATRIX 1-8 (GROUP/AUX, MATRIX selectable)
STEREO (L, R), MONO (C)
CUE (L, R, C), TB/OSC (CUE C, TB/OSC automatic select)
PEAK LED (red) turns on when pre-LineAmp level reaches 3dB below clipping.
+15/··/0 LED (yellow) turns on when pre-LineAmp level reaches +15/<3dB step>/0dB.
-3/··/-39 LED (green) turns on when pre-LineAmp level reaches -3/<3dB step>/-39dB.