Parameter Overview - THOMSON MEC 310#GENSET CONTROLLER Installation And Operation Manual

Parameter group 1 (Disp. view settings)
6181 Start prepare
6183 Start On time
6184 Start Off time
6211 Cool-down
6212 Extended stop
Parameter group 2 (Disp. view settings)
1030 Overcurrent 1: Delay + Setpoint
1040 Overcurrent 2: Delay + Setpoint
1150 Overvoltage 1: Delay + Setpoint
1160 Overvoltage 2: Delay + Setpoint
1170 Undervoltage 1: Delay + Setpoint
1180 Undervoltage 2: Delay + Setpoint
1210 Overfrequency 1: Delay + Setpoint
1220 Overfrequency 2: Delay + Setpoint
1240 Underfrequency 1: Delay + Setpoint
1250 Underfrequency 2: Delay + Setpoint
1450 Overload 1: Delay + Setpoint
1460 Overload 2: Delay + Setpoint
Parameter group 3 (Disp. view settings)
4220 Fuel 1.1: Delay + Setpoint*
4230 Fuel 1.2: Delay + Setpoint*
4620 Fuel 1.3: Delay + Setpoint*
4600 V-belt: Delay
4610 Charger gen: Delay
6350 D+: Delay
6550 Fuel pump: Delay*
6551 Fuel pump 1: Setpoint*
6552 Fuel pump 2: Setpoint*
* Only shown if multi-input 1 is set to VDO
Always shown parameters in display
4560 Hz/V failure timer
4580 Stop fail
4960 Battery low 1: Delay + Setpoint
4970 Battery High: Delay + Setpoint
6101 Running time
6105 kWh reset
6112 Service timer 1: Hours
6113 Service timer 1: Days
6116 Service timer 1: Reset
6122 Service timer 2: Hours
6123 Service timer 2: Days
6126 Service timer 2: Reset
6130 Alarm horn
PM075 REV 2 09/08/20
MEC 310 GENSET CONTROLLER

Parameter overview

7513 Service mode (RTU/ASCII)
7560 Engine I/F
Hour adjust. ( "Sync. clock" to PC button)
Minutes adjust. ( "Sync. Clock" to PC button)
Seconds Adjust.( "Sync. Clock" to PC button)
Date adjust ( "Sync. Clock" to PC button)
Month adjust ( "Sync. Clock" to PC button)
Year adjust ( "Sync. Clock" to PC button)
Parameters only configurable from USW
1000 Reverse power
2150 Phase sequence error
2280 Phase rotation
2160-2170 GB control
2770 EIC control
3000-3050 Digital input term. 10-15
3490 Emergency stop
3400...3420 Binary multi input settings
4120...4390 mA input settings
4310...4470 VDO multi input settings
4510 Gen. overspeed 1
4520 Gen. overspeed 2
4580 Stop fail
4630 Low water temp.
4950 Battery low 2
5000...5060 Relay functions
6001...6005 Nominal settings 1
6006 Enable nom. Settings
6011...6015 Nominal settings 2
6021...6025 Nominal settings 3 (1 ph)
6031...6035 Nominal settings 4 (2ph)
6041 Transformer U pri. Gen.
6042 Transformer U sec. Gen.
6043 Transformer I pri. Gen.
6044 Transformer I sec. Gen.
6080 Language
6101 Running time
6160 Run status
6171 Tacho – teeth
6173 Tacho – run setpoint
6191 Start attempts
6213 Cool-down temperature
6214 Cool-down reference
6290 Idle mode
6320 Engine heater ON
Page 88 THOMSON TECHNOLOGY