Analogue Inputs 0(4)-20Ma - THOMSON MEC 310#GENSET CONTROLLER Installation And Operation Manual

The scaling of the 0(4)-20mA inputs for correct display reading can only be done via the TPS 300
software.
4-20mA inputs have wire break function. Wire break alarm will be active when
current goes below 2,5mA. It's not possible to disable the wire break function.
4120 0-20 4-20mA 1.1
No. Setting
4121 0(4)-20mA 1.1
4122 0(4)-20mA 1.1
4123 0(4)-20mA 1.1
4124 0(4)-20mA 1.1
4125 0(4)-20mA 1.1
4126 0(4)-20mA 1.1
4130 0-20 4-20mA 1.2
No. Setting
4131 0(4)-20mA 1.2
4132 0(4)-20mA 1.2
4133 0(4)-20mA 1.2
4134 0(4)-20mA 1.2
4135 0(4)-20mA 1.2
4136 0(4)-20mA 1.2
4250 0-20 4-20mA 2.1
No. Setting
4251 0(4)-20mA 2.1
4252 0(4)-20mA 2.1
4253 0(4)-20mA 2.1
4254 0(4)-20mA 2.1
4255 0(4)-20mA 2.1
4256 0(4)-20mA 2.1
4260 0-20 4-20mA 2.2
No. Setting
4261 0(4)-20mA 2.2
4262 0(4)-20mA 2.2
4263 0(4)-20mA 2.2
4264 0(4)-20mA 2.2
4265 0(4)-20mA 2.2
4266 0(4)-20mA 2.2
PM075 REV 2 09/08/20
MEC 310 GENSET CONTROLLER

Analogue inputs 0(4)-20mA

Min. setting
Set point 4mA
Delay 0.0 s
Output A R0 (none)
Output B R0 (none)
Enable OFF
Fail class
Min. setting
Set point 4mA
Delay 0.0 s
Output A R0 (none)
Output B R0 (none)
Enable OFF
Fail class
Min. setting
Set point 4mA
Delay 0.0 s
Output A R0 (none)
Output B R0 (none)
Enable OFF
Fail class
Min. setting
Set point 4mA
Delay 0.0 s
Output A R0 (none)
Output B R0 (none)
Enable OFF
Fail class
Page 96
Max. setting Factory
setting
20mA 10mA
100.0 s 5.0 s
R26 (relay 26) R0 (none)
R26 (relay 26) R0 (none)
ON OFF
See description of fail classes
Max. setting Factory
setting
20mA 10mA
100.0 s 5.0 s
R26 (relay 26) R0 (none)
R26 (relay 26) R0 (none)
ON OFF
See description of fail classes
Max. setting Factory
setting
20mA 10mA
100.0 s 5.0 s
R26 (relay 26) R0 (none)
R26 (relay 26) R0 (none)
ON OFF
See description of fail classes
Max. setting Factory
setting
20mA 10mA
100.0 s 5.0 s
R26 (relay 26) R0 (none)
R26 (relay 26) R0 (none)
ON OFF
See description of fail classes
THOMSON TECHNOLOGY