Operation Indication Output (Version S300); Alarm Indication Output (Version S300); Fire Place Protection (Version 1.1) - Salda SMARTY XP Mounting And Installation Instruction
Source: salda.lt/en, vetter-lufttechnik.de
Hide thumbs
Also See for SMARTY XP:
- Mounting and installation instruction (48 pages) ,
- Mounting and installation instruction (60 pages)
Table of Contents
Advertisement
KNX PL-Link, galvanic
isolation, 40mA rated
2
1
T15
To air quality sensor
or remote controller
After connection, configuration has to be performed. For more information see section "ACCESSORIES SETUP (VERSION S300)".
Date
2022-01-17
Ed.
mindaugasbeleckas
Appr.
8.12. OPERATION INDICATION OUTPUT (VERSION S300)
Date
Name
Original
2
If indication about the status of the air handling unit is needed, it can be connected to dedicated Q24 signal on T7:1. When AHU is ON, indication
output will provide voltage for indicating device.
After connection, configuration has to be performed. For more information see section "ACCESSORIES SETUP (VERSION S300)".
1
2
Q34
WARNING: High voltage on output.
4
5
8.13. ALARM INDICATION OUTPUT (VERSION S300)
In the same way as operation indication, alarm indication signal can be provided by the control board. Indicator has to be connected to Y1 output
on T19:1.
Output digital relays 24-230 V AC, max 6.3A,
Modbus slave port1 over
normally open/closed
RS485, HMI/RU interface
3
2
1
1
2
1
4
3
T7
T12
Modbus RTU
Operation indication output signal (L, 230V)
WARNING: High voltage on output.
NOTE: lower than 0,05A loads can operate incorrectly.
8.14. FIRE PLACE PROTECTION (VERSION 1.1)
2022-01-17
EPLAN
mindaugasbeleckas
Project template with identification structure in accordance with IEC standard: Page structure with higher-level function and mounting location
Wiring diagram.
Replacement of
Automation controller C zone, X23 connector.
3
2
1
T3
Ref
D2
NO/NC switch
GND
+24VDC
SMARTY v2023.2
Connected by user
Modbus slave port1 over
RS485, HMI/RU interface
2
1
3
T12
Modbus RTU
EPLAN
Project template with identification structure in accordance with IEC standard: Page structure with higher-level function and mounting location
Replacement of
Replaced by
3
4
3
2
1
T3
Ref
D1
Smoke
detector
Figure 8.12.1. Operation indication output connection
GND
+24VDC
Connected by user
6
7
2
1
Q24
Figure 8.13.1. Alarm indication output connection
EPLAN Software & Service
GmbH & Co. KG
Replaced by
3
2
1
T3
Ref
D2
NO/NC switch
GND
+24VDC
Connected by user
Figure 8.11.1. D2 digital input connection
EPLAN Software & Service
Dampers
GmbH & Co. KG
5
6
Output digital relays 24-230 V AC, max 6.3A,
normally open/closed
4
3
2
1
T7
Q24
Operation indication output signal (L, 230V)
8
Output triac, 230V AC, max. 10A (<1s),
nominal current: 0,05-1A.
3
2
1
T3
1
2
T19
Ref
D2
Y1
NO/NC switch
Alarm indication output signal (L, 230V)
GND
+24VDC
Connected by user
Dampers
IEC_tpl001
7
8
Output triac, 230V AC, max. 10A (<1s),
nominal current: 0,05-1A.
2
T19
Alarm indication output signal (L, 230V)
9
IEC_tpl001
=
+
Page
2
Page
2 /
2
9
1
Y1
=
+
Page
2
Page
2 /
2
EN |
41
Advertisement
Table of Contents
