Table of Contents
Advertisement
Command Function
Transmitter and Receiver (continued)
Information requests (continued)
Information request
KEY:
X$
= Input video signal status
X^
= Display input HDCP status
X&
= Output HDCP status
X(
= Device type
X2*
= Fiber link detection
X2(
= Fiber optic mode
Telnet port
Set Telnet port map
View Telnet port map
KEY:
X3$
= Enable Telnet port 23
X3%
= Port number
Echo for SIS over SSH (port 22023)
Enable Echo
Disable Echo
View Echo status
KEY:
X3)
= Enable or disable Echo
Verbose mode
Set verbose mode
View verbose mode
NOTE:
Verbose mode will revert back to default in the event of a power cycle, disconnect from dataviewer, or disconnect from the Ethernet.
X1&
KEY:
= Verbose mode
Resets
Absolute system reset
Reset unit settings
Reset audio gain and attenuation
SIS Command
(Host to Unit)
I
Verbose mode 2/3
Response description:
Fiber link A•Fiber link B•Signal input•Input HDCP•Output HDCP•Input audio•Transmitter•Fiber mode
Example
0
= Not detected
0
= No source detected
3
= Source with no HDCP present
0
= No active sink detected
2
= Sink detected, output not encrypted
TX
RX
or
0
= Not detected
SM
MM
or
E
X3$
}
Z
PMAP
E
}
ZPMAP
0
= Off (default)
Response is 5 digits with leading zeros, for example
E
}
1ECHO
E
}
0ECHO
E
}
ECHO
0
= Off
E X1&
}
CV
E
}
CV
0
= Clear/none (default)
2
= Tagged response for queries
E
}
ZQQQ
E
}
ZXXX
E
}
ZA
FOX3 T 101 Transmitter and FOX3 R 101 Receiver • SIS Configuration and Control
Response
Additional description
(Unit to Host)
X2*
X$
SFPALnk
SFPBLnk0 • SigI
•
X2*
Inf00*SFPALnk
SFPBLnk0 • SigI
•
X2(]
•
SFPALnk1 • SFPBLnk0 • SigI1 • HdcpI2 • HdcpO0 • AudI0 • TX • MM
Signals are detected on the two fiber links, a signal is detected on the
input, the input and output are HDCP devices, the digital audio input is
selected, the device is a transmitter, and the fiber mode is singlemode.
1
= Detected
2
= Source with HDCP detected (default)
1
= Sink detected, output encrypted
1
= Detected
X3%]
PmapZ
Set Telnet port map to
X3%]
23
= Telnet port 23 enabled.
00000
]
Returns command entered with
Echo1
response.
]
Returns response only.
Echo0
X3)]
1
= On (default)
X1&]
Vrb
X1&]
1
= Verbose mode
3
= Verbose mode and tagged responses for queries
]
Zpq
Master reset, resets IP address and
subnet mask to default.
]
Zpx
Resets unit to factory default.
]
Reset audio gain and attenuation to
Zpa
default levels.
X^
X(
HdcpI
HdcpO0 • AudI0 •
•
•
•
X$
X^
HdcpI
HdcpO0 • AudI0 •
•
•
]
X3$
.
00023
or
.
X2(]
X(
]
17
Advertisement
Table of Contents
