Advertisement
Quick Links
FOX3 T 101 and FOX3 R 101 • Setup Guide
This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX3 T 101 and
FOX3 R 101 fiber optic transmitter and receiver.
WARNING:
The FOX3 T 101 and FOX3 R 101 output continuous invisible light (Class 1 rated), which may be harmful to
the eyes; use with caution. Plug the attached dust caps into the optical transceivers when the fiber cable is unplugged.
CLASS 1 LASER PRODUCT, see the FOX3 T 101 and FOX3 R 101 User Guide, at www.extron.com.
AVERTISSEMENT :
peut être dangereux pour les yeux, à utiliser avec précaution. Branchez les protections contre la poussière dans l'ensemble
émetteur/récepteur lorsque le câble fibre optique est débranché.
Produit laser de classe 1, voir le FOX3 T 101 et FOX3 R 101 User Guide sur
Installation
Step 1 — Mounting
Turn off or disconnect all equipment power sources and mount the transmitter and receiver as required. For mounting details and
considerations, see the FOX3 T 101 and FOX3 R 101 User Guide at www.extron.com.
Step 2 — Input and Output Connections
INPUT
P OW E R
12V
- - - -A M A X
HDMI
A
A A
B
B B
Figure 1.
FOX3 T 101 Rear Panel
a.
Connect an HDMI video source to the HDMI input (see figure 1,
b.
If desired, connect an HDMI video display to the Loop Out port (
c.
Connect an HDMI display to the HDMI output (see figure 2,
Step 3 — Throughput Connections
NOTE:
See the image on the right for fiber cable connections. Connect the transmitter (see figure 1 and
D
figure 2,
) to a receiver in one of two ways:
•
One way (transmitter to receiver) only, perform step 3a.
•
Two way (transmitter to receiver and return), perform steps 3a and 3b.
a.
Connect the fiber between the transmitter A Out port and the receiver A In port (
NOTE:
Ensure that the transmitter and connected receiver are in the same transmission mode,
singlemode (SM) or multimode (MM) and use the correct SM or MM fiber cable to connect the
devices.
b.
To return serial data from the receiver to the transmitter, connect a cable between the receiver A Out port
and the transmitter A In port (
SFP Link LEDs —
•
Transmit Optical OUT LED lights solid green when powered and is off when there is no power on the endpoint.
•
Receive Optical IN LED lights solid green when light is present and is off when there is no power or light present.
Le FOX3 T 101 et FOX3 R 101 émet une lumière invisible en continu (conforme à la classe 1) qui
FOX3 T 101
A
RESET
LOOP OUT
OUT
IN
C
C C
D
D D
E
E E
2
).
www.extron.com
OUTPUT
P OW ER
12V
-- --A MA X
HDMI
A
A A
F F
F
Figure 2.
FOX3 R 101 Rear Panel
B
) on the transmitter.
C
) on the transmitter for a local display.
F
) on the receiver.
1
).
(en anglais).
FOX3 R 101
A
RESET
OUT
IN
D
D D
E
E E
A
OUT
IN
Transmitter
1 1
2 2
2 2
1 1
A
Receiver
OUT
IN
1
Advertisement
Related Manuals for Extron electronics FOX3 101
Summary of Contents for Extron electronics FOX3 101
- Page 1 FOX3 T 101 and FOX3 R 101 • Setup Guide This guide provides quick start instructions for an experienced installer to set up and operate the Extron FOX3 T 101 and FOX3 R 101 fiber optic transmitter and receiver. WARNING: The FOX3 T 101 and FOX3 R 101 output continuous invisible light (Class 1 rated), which may be harmful to the eyes;...
- Page 2 Step 4 — Power Connection figure 1 and figure 2, Connect the provided 12 VDC power supplies to the rear panel captive screw power inlet (see page 1). ATTENTION: • Do not connect any external power supplies until you have read the ATTENTION notifications in the Power Supply section of the user guide for that device.