Viking VFR-500 Manual page 64

Wiring Diagram Program #34
Single Hazard Latching Solenoid with Remote reset
FROM DEDICATED UNSWITCHED
CIRCUIT IN SERVICE PANEL
120VAC-240VAC 50/60 HZ
USE 14AWG OR HEAVIER GAUGE
WIRE WITH 600V INSULATION
LINE
NEUTRAL
EARTH GROUND
AC IN CONNECTOR
BATTERY CABLE
OBSERVE POLARITY
POS NEG
12V BATT.
NOTES:
1. Connect only UL Listed 24VDC devices to indicating
circuits.
2. Connect EOL Diode assembly IN SERIES with solenoid
on release circuit
3. Install EOLR (provided) on all unused circuits.
4 Polarity is shown on indicating circuits in an activated
(off-normal) condition.
5. Polarity reverses when output is activated.
6. Maximum current per output is 3 Amp. Maximum voltage
is 33VDC.
7. Outputs identified as Release are Special Application. All
other outputs are Regulated 24 VDC, Rated 3 Amp each, 3
Amp total for all 4 circuits.
8. All initiating and NAC/Release circuits are supervised and
power limited. See Main Board Wiring Specifications for
wire routing instructions. All frequencies are continuous.
9. Refer to Appendix A for test and maintenance information
VFR-500 PROGRAM TEMPLATES • 5403799 • REV A • 9/23
Fuse
4A-250VAC
P-Comm
Time Lag
+ -
N L
PLINK
NON-POWER
LIMITED AND
SUPERVISED
PANEL OUTPUTS (INDICATING CIRCUITS)
RELEASE
GENERAL SUPV
NON-POWER
ALARM BELL CIRCUIT
LIMITED AND
BELL
SUPERVISED
OUTPUT
OUTPUT OUTPUT
BATT 1 2
RED +
BLACK -
POS NEG
5.1K 5.1K
EOLR EOLR DIODE
12V BATT.
ASSY
OBSERVE POLARITY
WHEN CONNECTING
SMOKE DETECTORS
5.1K 5.1K
EOLR EOLR
LOW AIR
PS40
VALVE
TAMPER
OSYSU
PVCS
EOLR
A B S + -
AUX OUT ZONE 1 ZONE 2 ZONE 3
SUP HEAT OR
SUP
LOW AIR SMOKE
VALV
SUP
TAMP DETECTORS
PS40
SUP
PANEL INPUTS (INITIATING ZONES)
CONNECT TO NORMALLY OPEN DEVICES
OR COMPATIBLE 2 WIRE SMOKE
DETECTORS.
MAXIMUM LINE RESISTANCE: 100 OHMS
(EXCEPT WITH LINEAR HEAT DETECTION)
OPTIONAL CA2Z MOUNTING LOCATION
ZONE 5 AND 6 ONLY
RELEASE
CIRCUIT
DRY CONTACTS RATED AT 3A, 30VDC
OUTPUT
TROUBLE
4
3
COM NO NC COM
ALARM CONDITION
TROUBLE CONDITION
SMOKE DET.
PANEL PROBLEM
HEAT DET.
LOSS OF AC
PULL STATION
LOSS OF BATTERY
WIRING PROBLEM WATERFLOW
EOL EOL
DIODE
ASSY
10. Maximum resistance on outputs is 10 ohms. Maximum
resistance on outputs programmed as releasing, is 1
divided by current requirements of solenoid.
See Appendix C for smoke detector compatibility data.
See Battery Calculation Worksheet for battery information.
64
5.1K
5.1K
5.1K EOLR
EOLR
EOLR
PS10
5.1K
EOLR
ZONE 4 ZONE 5 ZONE 6 ZONE 7
HEAT OR SUP SUP MANUAL
SMOKE RELEASE
DETECTORS
RELAY CONTACTS
WTRFL
ALARM SUPV
RELEASE
NO NC COM NO NC COM NO NC
SUPERVISORY
LOW AIR
VALVE TAMPER
OPTIONAL
CA2Z CLASS
A MOULE
EACH CA2Z WILL
CONVERT 2 CLASS B
ZONES INTO 2
CLASS A ZONES
OPTIONAL CLASS A
CONNECTIONS
EOLR IS NOT USED
FOR CLASS A
DWG #3550-3
WATERFLOW
RELEASE
Legend
Initiating device
Notification appliance
eAEROSOL
eA
z
eMatch Protection assy.
End-of-Line diode assy.