1. The actions described in these instructions are strictly reserved for contractually AUTHORISED TECHNICAL SERVICES (ATS) and personnel who have successfully completed training by Girbau 2. The company responsible for the Authorised Technical Service accepts full liability for the work done and any possible consequences that may derive from it.
Page 5
Safety Instructions Before beginning any procedure on machines equipped with an inverter or equipment with capacitative loads, wait for at least five minutes (10 minutes on equipment with a power rating greater than 25 kW) after the electrical disconnection, to eliminate risk of residual voltage. Close and mechanically lock the manual WATER, GAS, STEAM, THERMAL OIL, COMPRESSED AIR, etc.
Page 6
Safety Instructions SYMBOLS USED IN MACHINE LABELLING Electrical risk High temperature risk Protective guard for elements carrying Handle with caution. an electric current. Use adequate protection. Risk of inhaling harmful or irritant Mechanical risk vapours Protective guard for moving parts. Keep the doors/covers closed.
Technical specifications 1. TECHNICAL SPECIFICATIONS Justification of the Design regulation. HS-6040, HS-6057, HS-6085, HS-6110 models. As they have a net drum volume higher than 150 l, they must follow EN 60204-1 standard. Tools needed for installation HS-6040; HS-6057; EH090; EH130 ...
Technical specifications EU Declaration of conformity HS-6040 model EU DECLARATION OF CONFORMITY Manufacturer: GIRBAU S.A. Address: Ctra. de Manlleu, km 1, 08500 Vic, Barcelona, SPAIN Identification of the machine Generic denomination: Function: Type: Washer extractor Washing in a water bath and extracting textiles Front loading Lavadora –...
Page 9
Technical specifications HS-6057 model EU DECLARATION OF CONFORMITY Manufacturer: GIRBAU S.A. Address: Ctra. de Manlleu, km 1, 08500 Vic, Barcelona, SPAIN Identification of the machine Generic denomination: Function: Type: Washer extractor Washing in a water bath and extracting textiles Front loading Lavadora –...
Page 10
Technical specifications HS-6085 model EU DECLARATION OF CONFORMITY Manufacturer: GIRBAU S.A. Address: Ctra. de Manlleu, km 1, 08500 Vic, Barcelona, SPAIN Identification of the machine Generic denomination: Function: Type: Washer extractor Washing in a water bath and extracting textiles Front loading Lavadora –...
Page 11
Technical specifications HS-6110 model EU DECLARATION OF CONFORMITY Manufacturer: GIRBAU S.A. Address: Ctra. de Manlleu, km 1, 08500 Vic, Barcelona, SPAIN Identification of the machine Generic denomination: Function: Type: Washer extractor Washing in a water bath and extracting textiles Front loading Lavadora –...
Page 14
Technical specifications Legend CONNECTIONS DIMENSIONS (Figures 1, 2) Water supply Height from the machine base Drain Distance from the centre of symmetry of the unit Second drain Depth Electrical connection inlet Height to door bottom Electrical connection inlet external dosing Gravity centre (GC) Product inlets external dosing Steam inlet connection...
Technical specifications Environment and positioning conditions MAXIMUM TEMPERATURE +41 (+104) MINIMUM TEMPERATURE ºC (ºF) +5 (+40) LIGHTING VENTING OPENING (sq.ft.) 300 (0.4) MAXIMUM RELATIVE HUMIDITY WORKING AREA mm (in) 1000 (39.4) REAR MAINTENANCE AREA mm (in) 900 (35.4) If the installation calls for more than one washer, please refer to the corresponding dimensions in section 2.4 and Figure 2.6 Connection table explanation Connection table explanation and symbols of section 1.6.
Technical specifications Electrical requirements Check table explanation in section 1.5. In brackets: USA / CANADA specific values HS-6040 / EH090 TOTAL TOTAL SWITCH HEATING (*1) WIRE (*2) POWER CONSUMP. CURRENT VOLTAGE (AWG) H / V 13.9 2.5 x 3 + 200V red.
Page 17
Technical specifications Check table explanation in section 1.5. In brackets: USA / CANADA specific values HS-6057 / EH130 TOTAL TOTAL SWITCH HEATING (*1) WIRE (*2) POWER CONSUMP. CURRENT VOLTAGE (AWG) H / V 21.1 6 x 3 + 200V red. 15.3 44.1 10 x 3 +...
Page 18
Technical specifications Check table explanation in section 1.5. In brackets: USA / CANADA specific values HS-6085/ EH190 TOTAL TOTAL SWITCH HEATING (*1) WIRE (*2) POWER CONSUMP. CURRENT VOLTAGE (AWG) 200V H / V 26.0 6 x 3 + 25.0 208V...
Page 19
Technical specifications Check table explanation in section 1.5. In brackets: USA / CANADA specific values HS-6110 / EH255 TOTAL TOTAL SWITCH HEATING (*1) WIRE (*2) POWER CONSUMP. CURRENT VOLTAGE (AWG) 200V H / V 31.8 10 x 3 + 208V 30.5 10 x 3 + H / V...
Transport and location 2. RECEIPT, TRANSPORT AND LOCATION Receipt The following should be checked on accepting delivery of the washer: Check that the product has not suffered any damage in transit. (Any damage caused in this way will not be attributable to the manufacturer, and the appropriate claim should be made against the party responsible for transporting the product.) ...
Page 21
DONE AS SHOWN IN FIG. 2.2. OTHERWISE THE CRATING AND THE WASHER COULD BE DAMAGED. Fig. 2.2 HS-6085, HS-6110, EH190, EH255 Remove the two small covers located in the upper part of the washer (Fig. 2.3). The transport handles are visible and accessible through the crating.
HS-6040, HS-6057, EH090, EH130: Detach the fixing screws of the two top covers and remove them. HS-6085, HS-6110, EH190, EH255: Detach the two small covers located in the top covers, front and centre part of the washer. The transport handles are visible and accessible.
Transport and location Washer location Conditions ATTENTION! HS-6 / EH6 WASHERS ARE SOFT-MOUNTED MACHINES AND THE STRESS TRANSMITTED TO THE FLOOR IS LOW. HOWEVER, THEIR WEIGHT IS CONSIDERABLE. INSTALL THE WASHER ON A SECURE BASE CAPABLE OF SUSTAINING THE WASHER’S WEIGHT. REFER TO STRENGTH REQUIREMENTS TABLE (section 3.3).
Transport and location Removal of shipping braces THIS OPERATION MUST BE CARRIED OUT BY THE AUTHORIZED TECHNICAL SERVICE. DO NOT REMOVE THE SHIPPING RESTRAINTS BEFORE PLACING THE WASHER IN ITS DEFINITIVE POSITION. NEVER START THE MACHINE UP WITHOUT FIRST REMOVING THE SHIPPING RESTRAINTS. INCOMPLIANCE WITH THIS PRECAUTION MAY CAUSE SERIOUS PHYSICAL DAMAGES TO PEOPLE AND IRREPARABLE DAMAGES TO THE WASHER.
TILT models. Assemble all the guards of the tilt system (section 5.7.) Fig. 2.9 2.6.2. HS-6085, HS-6110, EH190, EH255 models Remove the screws securing the side guards at the top. Loosen the screws holding the lower guard and separate them from the machine (Fig.
HS-6040, HS-6057, EH090, EH130 models As a safety measure, the drain elbow pipe must not be modified. HS-6085, HS-6110, EH190, EH250 models. In those installations where the length of the drain pipe delivered by the manufacturer must be modified, the minimum length must always be greater than 850mm (34 in.) Choose one of the following options depending on the possibilities for installation and the regulations in force in the country where the installation is being carried out.
Installation 3.1.2. Direct connection of the washer drain to the manifold Facilities preferring this option to the open box option (recommended option) must respect the following precautions: Provide next to the connection point of each machine to the manifold, with a manifold ventilation outlet A reaching the outside, set at a height of 60 in.
Connect the hoses to the filters. Do not forget the seals. Fig. 3.4 IMPORTANT! HS-6040, HS-6057, HS-6085 and HS-6110 models EC certified. SIPHONAGE CONTAMINATION PREVENTION If the washer extractor is directly connected to the water supply, an antisiphon device must be connected either to the external supply inlet or prior to every connection.
Page 30
Connect hot water. Inlet Connect cold or hot water according to the washer configuration. HS-6040; HS-6057; EH090; EH133 HS-6085; HS-6110; EH190; EH255 Fig. 3.5 TILT MODELS The location of the water supply must allow that hoses accommodate the washer's movements during loading and unloading operations.
Page 31
Installation Assembling the connection couplings for AUSTRALIA IMPORTANT 20mm dual check valve supplied with machine must be installed on the cold water inlet to the machine. This valve is designed to prevent cross connection (back siphonage) and complies with AS/NZS Standard 2845.1 (Watermark) ...
Installation Electrical connection 3.3.1. Previous requirements CHECK THAT THE POWER AND FREQUENCY OF THE ELECTRICAL SUPPLY CORRESPONDS TO THOSE OF THE WASHER. Check the nameplate posted on the back panel of the machine. ALL THE MATERIALS USED IN THE ELECTRICAL INSTALLATION MUST COMPLY WITH THE STATUTORY SAFETY STANDARDS APPLICABLE TO EACH COUNTRY.
Installation Safety switch. Install an Automatic on/off Switch, outside the washer, with individual protection for each machine. Characteristics: number of poles and intensity: consult ELECTRICAL CONNECTION table (section 1.6) C type with top opening at 0.12 in (3 mm) ...
Machines in USA/Canada: assemble the steam inlet hose to the filter inlet. ATTENTION! HS-6085, HS-6110, EH190 and EH255 MODELS ONLY. The admission of steam in the bath causes strong vibrations that can damage the inner drum bottom. To avoid them, the machine has a pneumatic injector device (Fig- 3.9).
Installation 3.4.1. Steam connection in TILT models ATTENTION! The end of the steam supply pipe end must be located in the same vertical plane as the steam inlet (V) of the washing machine. Otherwise the tilted movements cause torsion effects that can loosen the threaded couplings. The value N of Figure 3.9 allows to locate the vertical plane of the steam inlet regarding to the centre of the washer.
Installation Compressed air connection (Figure 3.13) HS-6040 TILT; EH090 TILT; HS-6057 TILT; EH130 TILT; HS-6085; EH190; HS-6110; EH255 models. Assemble the pressure gauge A and seal the thread with Teflon or other sealing component. Pressure (min-max.): 6-7 bar, (87-100 PSI). The machine is provided ...
Installation TILT MODELS Electrical conductors must be flexible and capable of accommodating the washer movements during the loading and unloading operations and secured at their ends. 3.6.2. HS-6040, HS-6057, EH090, EH130 models The connection of the external dosing electrical signals takes place on the terminals of A8 board, located in the electrical connection box (box which contains the switch breaker) Fig.
Installation 3.6.3. HS-6085, HS-6110, EH190, EH255 models The connection of the external dosing electrical signals takes place on the terminals of A4 and A6 boards, located at the lower part of the washer electrical box (Fig. 3.17). If you use dosing signals coming from A-4 and A-6 board, you must link the COM terminal of each board (X6-1 and X3- 1) by means of an electric insulation conductor of 0.75 mm2...
Page 39
Installation RELAY CONTACTS POWERED FROM THE WASHER CONTROL CIRCUIT. Use of four dosing signals The dosing signals from 1 to 4 originate from the board. Supply terminal COM from terminal X0-A of the board A4, (cable not supplied) Figure 3.19. Supply the common phase of the signal outputs from XO-B ...
Installation 3.6.4. Connection order of the dosing signals (according to the different machine models) HS-6040, HS-6057 HS-6085, HS-6110, EH90, EH130 EH190, EH255 Dosing signal Dosing BOARD TERMINAL BOARD TERMINAL signal COMMON COMMON A4 d-10 d-11 d-12 COMMON A6 Cod. 511485...
Installation 3.6.5. External dosing hoses connection The washer is supplied with a manifold with (A, fig. 3.21): 8 inlets with an outside diameter of 3/8 in (10 mm). 1 inlet with an outside diameter of 1/2 in (12 mm). ...
Installation External signal Connection External signal It is possible to use an order from the washing machine control to issue an end of program or alarm warning. See Inteli control Operation Manual for further information. External signal specifications. Free voltage contact between terminals X4-5 and X4-6 on the A6 board. Maximum intensity allowed: 1A.
Installation Emergency stop in coin-op installations IN ACCORDANCE WITH SAFETY REQUIREMENTS FOR INDUSTRIAL MACHINERY STANDARD (UNE- EN ISO 10472-1,5-2) AND OTHER SAFETY REQUIREMENTS, THE LAUNDRY OWNER / USER IS RESPONSIBLE FOR INSTALLING A REMOTE LOCATED EMERGENCY STOP DEVICE, CONNECTED TO EACH MACHINE. Device conditions To be located in a visible place, separated from all machines and easily accessible.
TILT models 4. TILT MODELS ATTENTION! Tilt models specific safety instructions During the assembling and operation verification of the TILT system strictly follow the safety precautions indicated at the beginning of this manual. The transport and assembling operations of tilt components must be carried out by the Authorised Technical Service.
TILT models TILT system specific protection elements Fixed guards: Covers at the machine sides. Protect the user from the contact with dangerous points and spattering. Moving guards: Front and side covers that permit the washer tilting. Protect the user from the contact with ...
Tilt system assembly Tilt hinge assembly Lift the washer and remove the crating (refer to chapter 2 about machine's transport). Place the machine on wooden pieces (B/Fig. 4.3) so the four supporting bases stay free and separated from the floor: value A: 8 inch (200 mm) minimum This clearance will permit the tilt hinges assembly.
Tilt system assembly Pneumatic actuators assembly (Figure 4.6) The arrow indicates the front of the machine. The pneumatic actuators, together with the supporting plates and the beams are delivered mounted in two equal assemblies A. Steps to assemble them to the washer: To determinate the position of each of the two ...
Tilt system assembly Adjustment of position detectors actuators (Figure 4.9). The actuators C are secured to the bases through slots permitting their movement. To adjust their position: The machine must be in the rest position. Loosen mounting screws D of actuators C of position ...