General Guidelines For Safe Operation - Raider RDP-AG67 User Manual

www.raider.bg
14

GENERAL GUIDELINES FOR SAFE OPERATION

Read all instructions carefully. Failure of the nature following instructions can cause electric shock, fire and / or
severe injuries. Keep these instructions in a safe place.
1. Safety in the workplace.
1.1. Keep your workplace clean and well lit. Disarray and poor lighting may contribute to the occurrence of an
accident.
1.2. Do not operate in an environment of grinding increased the risk of explosion, close to flammable liquids,
gases or powders.
During operation of the separate grinding sparks that can ignite powders or fumes.
1.3. Keep children and bystanders at a safe distance while working with angle grinders.
If your attention is diverted, you may lose control over grinding.
2. Safety when working with electricity.
2.1. Plug the grinding must be suitable for contact. In no case is allowed to modify the structure of the plug.
When working with electrical zero, do not use plug adapters.
Using original plugs and sockets reduces the risk of electric shock.
2.2. Avoid touching your body to earthed bodies, for example pipes, heaters, stoves and refrigerators. When
your body is grounded, risk of electric shock is greater.
Keep grinding from rain and moisture.
Infiltration of water into the grinding increases the risk of electric shock.
2.3. Do not use a power cord for the purposes for which it is not provided, for example to carry grinders for
cable or removing the plug from the outlet. Protect cords from heat, oil and contact with sharp edges or points
of mobile machines.
Damaged or twisted cables increase the risk of electric shock.
2.4. When you work with the angle grinder out, switch the machine only in installations equipped with electric
switch "Fi" RCD (Residual Current Device). RCD must be no more than 30 mA. Use an extension cord suitable
for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
2.5. If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected
supply. Use of an RCD reduces the risk of electric shock.
Using the extension, designed for outdoor use reduces the risk of electric shock.
3. Safer way of working.
3.1. Be concentrated, watch their actions carefully and act cautiously and prudently. Do not use the angle grinder
when you are tired or under the influence of drugs, alcohol or narcotic drugs.
A moment of distraction at work grinding may have the effect of extremely serious injuries.
3.2. Work with protective work clothing and always with safety glasses.
Wearing Suitable for grinding and the activities of personal protective equipment, such as respiratory masks,
healthy, tightly closed shoes grapple with a stable, protective helmet and silencers (hearing protectors), reduces
the risk of accident.
3.3. Avoid the danger of incorporating the grinding inadvertently. Before you turn the plug into the power
supply network, make sure the trigger switch is in position "off". If you wear when grinding, keep your finger on
the trigger switch, or if you submit a voltage of grinding when turned on, there is the risk of accident.
3.4. Before you turn implies that we are sure you remove all of its utilities and wrenches.
Utilities, forgotten rotating unit can cause injuries.
3.5. Avoid unnatural positions of the body. Work in a stable position of the body at any time and keep the
balance. So you can control the grinding better and safer if unexpected situations arise.
3.6. Work with appropriate clothing. Do not operate with loose clothing or ornaments. Keep your hair, clothes
and gloves at a safe distance from rotating the grinding units. Robes, attire, long hair can be caught and carried
away by rotating units.
3.7. If it is possible to use external aspiration system, make sure it is switched on and functioning properly. Use
of the aspiration system reduces the risks due to the discharge dust at work.
4. Thoroughly respect to angle grinders.
4.1. Do not overload grinders. Use angle grinders only as intended. You will operate better and safer when using
the right angle grinder manufacturer in the specified range of load.
4.2. Do not use the angle grinder with a starting switch is damaged.
Angle grinder, which can not be excluded and included as intended by the manufacturer, is dangerous and
should be repaired.
4.3. Before you modify the settings of the angle grinder to replace work tools and additional accessories as well
as a long time when you will not use grinders, unplug the plug from the supply network. This measure eliminates
the danger of triggering the grinding inadvertently.
4.4. Keep grinding in places where they can be reached by children. Do not allow them to be used by persons
who are not familiar with how to work with them and have not read those instructions. When you are in the
hands of inexperienced users, grinders can be extremely dangerous.
4.5. Keep grinding their care. Check whether the mobile units operate impeccable, whether it spells, if there is
a broken or damaged item which distort or alter the functions of the grinding machine. Before using the angle
grinder, make sure that the damaged parts to be repaired. Many accidents are caused by poorly maintained
power tools and appliances.
4.6. Use the angle grinder, attachment, working tools according to the manufacturer's instructions. In doing
so must comply with specific operating conditions and operations to perform. Using grinders of various
applications provided by the manufacturer increases the risk of accidents.
5. Maintain.
5.1. Repairing your electric tools is best carried out only by qualified specialists in workshops RAIDER, which
used only original spare parts. Thus it ensuring their safe operation.
6. Guidelines for the safe handling, specific grinding purchased by you. General guidelines for safe operation
with a disc grinder and sandpaper, clean with wire brush and abrasive cutting disk.
6.1. This grinding can be used for grinding with carboflex drive and sandpaper, clean with wire brush, polishing
and cutting carboflex disk. Follow all instructions and warnings complying with technical parameters and the
adjusted images. Failure to follow the following instructions, the consequences may be an electric shock, fire
and / or severe injuries.
6.2. This angle grinder is not suitable for polishing. Carrying out activities for which the grinding is not
intended, may be dangerous and cause injuries.
6.3. Do not use additional devices which are not recommended by the manufacturer for this particular power.
The fact that you can attach to specified device or machine working tool does not ensure safe working with him.
6.4. Allowable speed of rotation of the working tools must be at least equal to the inscribed plaque on the
grinding speed of rotation. Working tools that rotate at a higher speed than the maximum indicated on the
angle grinder can break and pieces of them high speed.
6.5. The outer diameter and thickness of the working tools must comply with the particulars specified in the
technical characteristics of your angle grinder. Working tools with inappropriate size may not be shielded as
15