Advertisement
Quick Links
Cable Cubby F55 Edge • Installation Guide
The Extron Cable Cubby F55 Edge is an edge-mount cable
access enclosure that integrates AV technology and power on
the furniture surface. It is designed for configurable rooms that
require semi-permanent AV connectivity, control, and power.
An integrated clamp system secures the enclosure to the
furniture without requiring tools or cutting.
This guide provides instructions for an experienced installer to
install and connect the Extron Cable Cubby F55 Edge Cable
Access Enclosure.
Kit Contents
Cable Cubby F55 Edge
Cable Cubby F55 Edge Kit Contents
Figure 1.
Planning
Read the following information before installing the Cable Cubby F55 Edge.
Check with Local and State Regulations Before Starting the Installation:
•
Ensure that the planned installation complies with building and electrical codes.
•
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check All Parts and Equipment Before Installation:
•
Ensure that all parts are present in each kit.
•
Ensure that necessary tools and equipment are available for the installation.
NOTE:
Excess cabling may cause clearance issues. Use zip ties to secure under-table cabling to prevent accidental contact
or entanglement (see
Flex55 Adapter Module (2)
Pry Tool (2)
Routing and Connecting Cables
Cable Grommet
Plate (2)
Grommet
Zip Ties (4)
Plugs (8)
on page 9).
Optional Accessories
ZipClip 100
ZipClip 200
ZipClip 400
PMK 155
1
Advertisement
Related Manuals for Extron electronics Cable Cubby F55 Edge
Summary of Contents for Extron electronics Cable Cubby F55 Edge
- Page 1 Cable Cubby F55 Edge Kit Contents Figure 1. PMK 155 Planning Read the following information before installing the Cable Cubby F55 Edge. Check with Local and State Regulations Before Starting the Installation: • Ensure that the planned installation complies with building and electrical codes.
-
Page 2: Application Diagram
The application diagram below shows a power, data, and video wiring setup from a laptop to a conference monitor. The setup is made simple by using the included Cable Cubby Flex55 Captive Cable Kit, installed in the Cable Cubby F55 Edge enclosure. - Page 3 Preparing the Cable Cubby F55 Edge The Cable Cubby F55 Edge enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations (see the example in figure 3). These modules can be installed either before or after the Cable Cubby F55 Edge installation. Optional Retractor modules can be installed with the appropriate brackets, sold separately.
- Page 4 Cubby F55 Edge enclosure. Note that half- and full-size modules can be snapped into the enclosure without removing the ). Retractor modules also can be installed, in any slot in the enclosure (see the Cable Cubby F55 Edge Retractor supports ( Setup Guide, available at www.extron.com, for more information).
- Page 5 Flex55 AC+USB 130 US Insert the module into the Cable Cubby. Attach additional devices here. Extron Cable Cubby Extron Cable Cubby Flex55 Edge Enclosure Flex55 Edge Enclosure Installing the Flex55 AC+USB 130 US into the Cable Cubby F55 Edge Enclosure Figure 6.
- Page 6 Attaching an Optional ZipClip Mounting Device to the Cable Cubby F55 Edge The ZipClip 100, 200, or 400 can be attached to the Cable Cubby F55 Edge in order to mount a power supply or other device to the Cable Cubby. Determine which ZipClip to use (depending on the device being attached) and in which orientation (vertical or horizontal).
- Page 7 Attaching an Optional PMK 155 Mounting Kit Follow these steps to attach a PMK 155 Mounting Kit to the Cable Cubby F55 Edge. The Cable Cubby F55 Edge is delivered with an accessory mounting bracket attached. Detach this bracket by removing its step two mounting screws (see figure 8).
- Page 8 Cable Cubby F55 Edge • Installation Guide (Continued) step 1 Attach the accessory bracket and PMK 155 to the Cable Cubby F55 Edge, using the two screws removed in Attaching the PMK 155 and Accessory Bracket to the Cable Cubby F55 Edge Figure 10.
- Page 9 Routing and Connecting Cables Organize and connect cables as shown in figure 12. Use zip ties (provided) to fasten the cables to the enclosure where needed. Zip tie locations on the inside of the clamps Routing and Managing the Cables Figure 12.
- Page 10 Appendix — Removing Modules from the Cable Cubby F55 Edge If the modules need to be replaced or removed from the Cable Cubby F55 Edge enclosure, the following diagrams show the procedure for removing modules with the provided pry tool. This process applies to any compatible Flex55 and EU module.
-
Page 11: Installation Overview
If using a PMK 155, remove the accessory bracket from the Cable Cubby F55 Edge and attach the bracket to the PMK 155. Re-install the accessory bracket with the PMK to the Cable Cubby F55 Edge. - Page 12 For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, see the Extron Safety and Regulatory Compliance Guide on the Extron website. www.extron.com © 2022 Extron — All rights reserved. 68-3569-50 Rev. A All trademarks mentioned are the property of their respective owners. 12 22 Worldwide Headquarters: Extron USA West, 1025 E.
Need help?
Do you have a question about the Cable Cubby F55 Edge and is the answer not in the manual?
Questions and answers