Advertisement
Quick Links
Cable Cubby F55 UT Enclosure • Setup Guide
This guide contains installation instructions for the Cable Cubby F55 UT, an
under-table enclosure compatible with optional Extron cable retractor, AV, control
and power modules. This compact design allows users convenient accessibility
from below the desk or table surface.
NOTE: For a complete and up-to-date list of compatible modules, see the
product page at www.extron.com.
Planning
Check local and state regulations before starting the installation:
…
Ensure that the planned installation complies with building and electrical codes.
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility
…
requirements
.
Check all parts and equipment before installation:
Ensure that all parts are present in each kit.
…
…
Ensure that necessary tools and equipment are available for the installation.
Kit Contents
Cable Cubby F55 UT
#8 - 1/2 inch pan-head wood screws
7.5 inch Cable tie-wraps
Pry tools
Tools Required for Installation
1/8 Inch Drill Bit
Phillips Screw Driver
4
4
2
Pliers
Drill
U S
B C
H A
R G
E R
12 0V
~
50 -6
0H
Safety Glasses
Marking Pen
z 6A
M A
X
D IS
P L
O N
A Y
V O
O F
L U
F
M E
P C
V ID
L A
E O
P T
O P
M U
T E
1
Advertisement
Related Manuals for Extron electronics Cable Cubby F55 UT
Summary of Contents for Extron electronics Cable Cubby F55 UT
- Page 1 Cable Cubby F55 UT Enclosure • Setup Guide This guide contains installation instructions for the Cable Cubby F55 UT, an under-table enclosure compatible with optional Extron cable retractor, AV, control and power modules. This compact design allows users convenient accessibility from below the desk or table surface.
-
Page 2: Application Diagram
Cable Cubby F55 UT • Setup Guide (Continued) Application Diagram The application diagram below shows an HDMI wiring setup from a laptop to a conference monitor, made simple by a Flex55 SuperPlate 103 module installed in the Extron Cable Cubby F55 UT enclosure. HDMI 120V... - Page 3 Preparing the Cable Cubby F55 UT The Cable Cubby F55 UT enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations (see the illustration below). These modules can be installed either before or after the F55 UT installation. Note that optional Retractor modules can only be installed (with the appropriate brackets, sold seperately) in the left and right ends of the enclosure.
- Page 4 The following illustration shows the process for installing the double-size Flex55 AC+USB 130 US Power Module into the Cable Cubby F55 UT enclosure. Note that half- and full-size modules can be snapped into the enclosure without removing the supports (...
-
Page 5: Preparing The Table
Preparing the Table Download and print the Cable Cubby F55 UT mounting template from the Extron website. Make sure that the template dimensions are to scale. Position the template over the intended mounting surface location, secure with tape, and mark the center of the holes where the mounting slots will be positioned. - Page 6 Cable Cubby F55 UT • Setup Guide (Continued) Mounting the Cable Cubby F55 UT NOTE: Take care not to drill through the table. If the table is too thin or of a different material than intended for the supplied #8 - 1/2 inch L wood screws, use an appropriate alternative.
- Page 7 Appendix - Removing Modules from the Cable Cubby F55 UT If the modules need to be replaced or removed from the Cable Cubby F55 UT enclosure, the following diagram shows the process for removing modules with the provided pry tool. This process applies to any compatible Flex55 and EU module.
-
Page 8: Installation Checklist
Removing Modules from the Cable Cubby F55 UT (see page 7) … If needed, remove modules from the Cable Cubby F55 UT with the provided pry tool For information on safety guidelines, regulatory compliances, EMI/EMF compatibility, accessibility, and related topics, Extron Safety and Regulatory Compliance Guide see the on the Extron website.