Advertisement
Quick Links
Cable Cubby F55 • Installation Guide
This guide provides instructions for an experienced
technician to install and connect the Extron
Cable Cubby F55.
The Cable Cubby F55 is a lift-up cable access, furniture
mountable enclosure for AV connectivity, remote control,
and power. The lid lifts up to expose the connectivity
interface at a comfortable and ergonomic angle. When
closed, the Cable Cubby is nearly flush with the table
surface.
Planning the Installation
Check with local and state regulations
before starting the installation
•
Ensure that the planned installation complies with
national and local building and electrical codes.
•
Ensure that the planned installation complies with the Americans with Disabilities Act or other accessibility requirements.
Check All Parts and Equipment
•
Ensure that all parts are present in each kit.
•
Ensure that necessary tools and equipment are available for the installation.
Kit contents
Figure 1.
Cable Cubby F55 Kit Contents
#10-32 Screws (4)
Cable Cubby F55
Flex55 Adapter Module (2)
Cable Grommet
Plate (2)
Grommet
Zip Ties (4)
Plugs (8)
Optional Accessories
ZipClip 100
ZipClip 200
ZipClip 400
Pry Tool (2)
Tweeker
1
Advertisement
Related Manuals for Extron electronics Cable Cubby F55
Summary of Contents for Extron electronics Cable Cubby F55
- Page 1 This guide provides instructions for an experienced technician to install and connect the Extron Cable Cubby F55. The Cable Cubby F55 is a lift-up cable access, furniture mountable enclosure for AV connectivity, remote control, and power. The lid lifts up to expose the connectivity interface at a comfortable and ergonomic angle.
- Page 2 Cable Cubby F55 Furniture Mountable Cable Access Enclosure Figure 2. Application Example Using the Cable Cubby F55 Enclosure Preparing the Table Determine the Best Location for the Enclosure • Ensure that the location where the Cable Cubby is to be installed is convenient for as many users as possible.
- Page 3 The Cable Cubby F55 enclosure supports Flex55 and EU modules, which can be installed in a variety of combinations. These modules can be installed either before or after the Cable Cubby F55 installation, in any slot of the enclosure. Determine where the connectivity modules and power module will be installed in the enclosure.
- Page 4 Insert the modules (in this example, the double-size Flex55 AC+USB 130 US), into the opening and snap them into the frame. Figure 5. Installing Flex55 and EU Modules into the Cable Cubby F55 Enclosure...
- Page 5 Attaching an Optional ZipClip Mounting Device to the Cable Cubby F55 The ZipClip 100, 200, or 400 can be attached to the Cable Cubby F55 with the included #10-32 screws, in order to mount a power supply or other device to the enclosure. Determine which ZipClip to use, and ensure there is ample space for the device and its cables.
- Page 6 Cable Cubby F55 • Installation Guide (Continued) Mounting the Cable Cubby F55 in the Table Step 1 — Mount the Cable Cubby Flush with the Table Ensure the side clamps are seated against the enclosure and positioned on the lower part of the shaft.
- Page 7 Cable Cubby F55 • Installation Guide (Continued) Step 2 — Under the Table, Adjust the Side Clamps on the Enclosure Lever Slide the clamp all the Ensure the Cable Cubby Rotate the side clamp way up against the bottom outward and ensure that is rmly seated in the table.
- Page 8 Cable Cubby F55 • Installation Guide (Continued) Routing and Managing Cables Organize and connect cables as shown in figure 8. Use zip ties (provided) to fasten the cables to the enclosure where needed. Manage the cables with the lid in the fully open position.
- Page 9 Removing Flex55 and EU Modules from the Cable Cubby F55 If the modules need to be replaced or removed from the Cable Cubby F55 enclosure, the following diagrams show the procedure for removing modules with the provided pry tools. This process applies to any compatible Flex55 and EU module.
- Page 10 Cable Cubby F55 • Installation Guide (Continued) Removing the Enclosure from the Table To remove the Cable Cubby F55 enclosure from its mounting location in the table, release the side clamps as shown below: NOTE: When the clamps cannot be loosened by hand, an Extron Tweeker or other small screwdriver may be necessary to help with leverage.
- Page 11 Remove bridge supports if necessary to accommodate a double-sized module. Note that removal of bridge • supports is irreversible. Cable and install half-, single- and double-size modules into the Cable Cubby F55. • (see page 5) 4. (Optional) Attach a ZipClip mounting device to the Cable Cubby F55 If using a ZipClip, determine which model to use (100, 200, or 400).
- Page 12 Extron Safety and Regulatory Compliance Guide on the Extron website. www.extron.com © 2023 Extron Electronics — All rights reserved All trademarks mentioned are the property of their respective owners. 68-3527-50 Rev. A Worldwide Headquarters: Extron USA West, 1025 E. Ball Road, Anaheim, CA 92805, 800.633.9876...