Multitech MT2834MR Owner's Manual page 84

PN 88300150
&Mn n = 0 or 1
$MIn** n = 0 or 1
$MBn n = speed
Nd d = 0 thru 9
NdNe d = 0 thru 9
e = any other
number 0-9
O
P
&Pn** n = 0 or 1
#Pn n=0 thru 2
Qn n = 0 or 1
&Qn n = 0 or 1
Rn n = 0 or 1
&Rn n = 0, 1 or 2
*Rn n = 0 or 1
&RFn n = 0 or 1
$Rn n = 0 or 1
Sr=n r = 0 thru 11,
13, 17-19, 24,
25, 30, 32, 34
Sr? r = 0 thru 11,
13, 17-19, 24,
25, 30, 32, 34
$SBn n = speed
&Sn n = 0, 1 or 2
&SFn n = 0 or 1
4/3/01
&L4D selects 4 wire Originate mode operation
*** &M0 means Async when on-line.
&M1 means Sync when on-line.
*** $MI0 disables MI/MIC option (**)
$MI1 enables MI/MIC option (**)
$MB75 selects ITU-T V.23 mode.
$MB300 selects 300 bps on-line.
$MB1200 selects 1200 bps on-line.
$MB2400 selects 2400 bps on-line.
$MB4800 selects 4800 bps on-line.
$MB9600 selects 9600 bps on-line.
$MB14400 selects 14400 bps on-line.
$MB19200 selects 19200 bps on-line.
$MB24000 selects 24000 bps on-line.
$MB28800 selects 28800 bps on-line.
*** $MB33600 selects 33600 bps on-line.
Dial stored telephone number "d". Do not include the letter D with this command.
Number Linking. If first number dialed is busy, another stored number may be
automatically dialed. For example, stored number "d" is dialed, and if busy, stored
number "e" is dialed.
Exit Command Mode and go into On-Line Mode.
*** Modem will pulse-dial numbers following the P.
*** &P0 means 60-40 pulse ratio.
&P1 means 67-33 pulse ratio.
*** #P0 means no parity.
#P1 means odd parity.
#P2 means even parity.
*** Q0 means Result Codes sent.
Q1 means Result Codes will be suppressed (quiet).
Q2 means Dumb Answer Mode.
*** &Q0 selects Multi-Tech command set.
&Q1 selects AT command set.
*** R0 means modem will not reverse modes.
R1 means modem will reverse modes.
&R0 lets Clear to Send act normally.
*** &R1 forces Clear to Send on.
&R2 drops for S24 period on disconnect.
*** *R0 disables ring message on callback modem.
*R1 enables ring message on callback modem.
&RF0 selects CTS follows RTS.
*** &RF1 selects CTS to act independently.
*** $R0 means disconnect after 12 retransmits.
$R1 means do not disconnect after 12 retransmits.
Sets value of Register "r" to value of "n",
where "n" is entered in Decimal format.
Reads value of Register "r" and displays
value in 3-digit Decimal format.
$SB1200 selects 1200 bps at serial port.
$SB2400 selects 2400 bps at serial port.
$SB4800 selects 4800 bps at serial port.
$SB9600 selects 9600 bps at serial port.
$SB19200 selects 19,200 bps at serial port.
$SB38400 selects 38,400 bps at serial port
$SB57600 selects 57600 bps at serial port.
*** $SB115200 selects 115200 bps at serial port.
&S0 forces Data Set Ready On.
*** &S1 lets Data Set Ready act normally.
&S2 Data Set Ready drop is regulated by S24 on disconnect.
*** &SF0 selects DSR follows CD.
84