Table of Contents
Advertisement
PN 88300150
$En
n = 0 or 1
&En
n = 0 thru 15
$EBn
n = 0 or 1
%En
n=0 thru 5
#Fn
n = 0, 1, 8,
or 9
&F
$Fn
n = 0 or 1
&Gn**
n = 0, 1 or 2 *** &G0 turns off ITU-T guard tones.
Hn
n = 0 or 1
$Hn
n = 1 thru 3
*Hn
n = 0 or 1
In
n = 0 or 1
L
L5
L6
L7
L8
#Ln
n = 0 thru 3 *** #L0 means modems negotiate V.42 Mode.
&Ln
n = 0,1,2A,
2D,4A,4D
4/3/01
*** $E0 disables 300 baud error correction.
$E1 enables 300 baud error correction.
&E0 means V.42 Normal Mode.
*** &E1 means V.42 Auto-reliable Mode.
&E2 means V.42 Reliable Mode.
&E3 means no modem-initiated flow control.
*** &E4 means CTS modem-initiated flow control.
&E5 means Xon/Xoff modem-initiated flow control.
*** &E6 means Xon/Xoff not passed through.
&E7 means Xon/Xoff passed through.
*** &E8 means Enq/Ack pacing off.
&E9 means Enq/Ack pacing on.
*** &E10 means Normal Mode flow control off.
&E11 means Normal Mode flow control on.
&E12 means Pacing off.
*** &E13 means Pacing on.
&E14 means data compression disabled.
*** &E15 means data compression enabled.
*** $EB0 enables 10 bit mode.
$EB1 enables 11 bit mode.
% E0 = Modem Won't Escape.
*** % E1 = +++ Method (default setting).
% E2 = Break Method.
% E3 = Either +++ or Break Method.
*** % E4 = Disables "OK" Response to +++ Escape Method.
% E5 = Enables "OK" Response to +++ Escape Method.
#F0 means no fallback when on-line.
#F1 means fallback from 28800 to 2400 bps
when on-line.
*** #F2 means fallback to 2400 from 28800 bps/fall forward when line improves.
&F loads factory default values from ROM.
*** &F8 loads factory defaults after &F.
&F9 loads RAM defaults after &F.
$F0 means do not fall back to normal connect if CR received.
*** $F1 means fall back to normal connect if CR received.
&G1 turns on ITU-T 550 Hz guard tone.
&G2 turns on ITU-T 1800 Hz guard tone.
H0 means Hang Up (go on hook).
H1 means Go Off Hook.
$H1 brings up Help Screen #1.
$H2 brings up Help Screen #2.
$H3 brings up Help Screen #3.
*** *H0 means modems busy out after disconnect disabled.
*H1 means modems busy out after disconnect enabled.
I0 requests modem ID #.
I1 requests firmware revision #.
Lists all stored telephone numbers in memory.
L5 lists all current operating parameters.
L6 lists all current S-Register values.
L7 lists additional parameters.
L8 lists on-line diagnostics
#L1 means MNP on and LAP-M off.
#L2 means LAP-M on and MNP off.
#L3 means no detection phase but go directly to LAP-M.
&L0 selects Dial-up line operation
&L1 allows a single attempt at laesed line connection
&L2A selects 2 wire Answer mode operation
&L2D selects 2 wire Originate mode operation
&L4A selects 4 wire Answer mode operation
83
Advertisement
Table of Contents
