Otto Bock AxonArm Ergo 12K501 Series Instructions For Use Manual
Hide thumbs
Also See for AxonArm Ergo 12K501 Series:
- Instructions for use manual (220 pages) ,
- Instructions for use manual (284 pages) ,
- Instructions for use manual (244 pages)
Related Manuals for Otto Bock AxonArm Ergo 12K501 Series
Summary of Contents for Otto Bock AxonArm Ergo 12K501 Series
- Page 1 AxonArm Ergo 12K501=* Instructions for use (qualified personnel) ..............
- Page 2 AxonArm Ergo 12K501=*...
-
Page 3: Table Of Contents
Table of contents Table of contents Foreword ................................Product description ............................Construction and Function ........................Definition of terms ..........................Intended use ................................ Indications for use ..........................Conditions of use ..........................Contraindications ..........................Qualification ............................Safety ..................................Explanation of warning symbols ...................... - Page 4 Table of contents 10.2.4 The movements of the Axon-Bus gripping component are becoming increasingly slower ......10.3 Axon ..............................AxonArm Ergo 12K501=*...
-
Page 5: Foreword
Foreword 1 Foreword INFORMATION Date of last update: 2022-07-07 ► Please read this document carefully before using the product and observe the safety notices. ► Instruct the user in the safe use of the product. ► Please contact the manufacturer if you have questions about the product or in case of problems. ►... -
Page 6: Intended Use
Intended use The product has a load capacity of up to 230 N in the locked state with a forearm lever length of 305 mm. The lock will slip under higher loads. Mechanical release With the product switched off or when the battery is drained, the elbow can be manually unlocked and locked again with a slight pull on the unlock cable. -
Page 7: General Safety Instructions
Safety 4.3 General safety instructions CAUTION Non-observance of safety instructions Personal injury/damage to the product due to using the product in certain situations. ► Observe the safety instructions and the stated precautions in this accompanying document. CAUTION Signs of wear and tear on the product components Injury due to faulty control or malfunction of the product ►... -
Page 8: Scope Of Delivery And Accessories
Scope of Delivery and Accessories CAUTION Independent manipulation of Axon-Bus components Injury due to faulty control or malfunction of the Axon-Bus prosthetic system. ► Manipulations to the Axon-Bus prosthetic system other than the tasks described in these instructions for use are not permitted. -
Page 9: Accessories
Preparing the product for use • 2 pc. bracket cover • 1 pc. lamination ring • 1 pc. 13Z146 lamination ring (for Axon-Bus terminal device) • 1 pc. clamp ring • 4 pcs. mounting brackets • 1 pc. spherical cord lock • 4 pc. Cable ties •... -
Page 10: Axonmaster
Preparing the product for use 6.2 AxonMaster Various control programmes and switching methods as well as the option of making refined patient-specific set tings are available for optimum adaptation to the patient. The standard programmes can be selected using the 560X500=* AxonSoft adjustment software and include predefined control options and switching methods. -
Page 11: Connecting The Axonmaster To The Easyplug
Preparing the product for use 6.2.5 Connecting the AxonMaster to the EasyPlug 1) Grease the plug of the AxonMaster cable with 633F11 silicone grease. 2) Connect the cable. 3) Apply 633F11 silicone grease around the plug and blanking covers to seal. 6.3 Installing the EasyPlug 1) Lubricate the groove, inner edge and thread of the lamination ring with 633F30 special grease. -
Page 12: Setting The Preflexion
Preparing the product for use 3) Mark the base position for the flexion angle (preflex ion) on the joint ball. Dimension Y = 1.5 cm. 4) Thread the belt under the axis. 5) Pull the belt up to the marking (dimension Y) with tweezers. - Page 13 Preparing the product for use Region 1 Minimal compensation that allows natural free swing of the arm while walking. Region 2 Compensation increases progressively with flexion of the arm and decreases during extension. Region 3 Compensation remains constant. If set correctly, the weight of the forearm is balanced by the compensation and the elbow remains flexed.
-
Page 14: Adjusting The Humeral Rotation Feature
Preparing the product for use 3) Secure the strap (e.g. using an artery clamp). INFORMATION: When using an artery clamp, verify that the jaws of the artery clamp have no sharp edges. Otherwise, tape over the jaws to protect the strap. 4) Loosen the screw on the strap clamp, but do not remove the strap clamp. -
Page 15: Handling
Handling 7 Handling 7.1 Charging the Battery The 757B501 AxonEnergy Integral must be charged prior to initial use. The 757B501 AxonEnergy Integral may only be charged with the 757L500 AxonCharge Integral. The charging process can only be performed with the 13E500 AxonMaster connected. -
Page 16: Open The Axon-Bus Gripping Component In An Emergency
Handling 7.7 Open the Axon-Bus Gripping Component in an Emergency This safety function allows the Axon-Bus gripping component to be opened regard less of the control signals present. 1) With the Axon-Bus prosthetic system switched on, press the charging receptacle button and hold for approximately three seconds until the Axon-Bus gripping component begins to open. -
Page 17: Legal Information
8.3 CE conformity Otto Bock Healthcare Products GmbH hereby declares that the product is in compliance with applicable European requirements for medical devices. The product meets the requirements of the RoHS Directive 2011/65/EU on the restriction of the use of certain haz... -
Page 18: Technical Data
Technical data (2) L’appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d’en com promettre le fonctionnement. Caution: Exposure to Radio Frequency Radiation. The installer of this radio equipment must ensure that the antenna is located or pointed such that it does not emit RF field in excess of Health Canada limits for the general population. -
Page 19: Fault Display And Fault Elimination
Appendices Manufacturer 10.2 Fault Display and Fault Elimination 10.2.1 LED flashes red and beeper sounds for 3 seconds Probable cause: Error in the Axon-Bus prosthetic system. Remedy: 1. Switch the Axon-Bus prosthetic system off and back on. 2. Check the plug connections in the socket. 3. - Page 20 Otto Bock Healthcare Products GmbH Brehmstraße 16 · 1110 Wien · Austria T +43-1 523 37 86 · F +43-1 523 22 64 info.austria@ottobock.com · www.ottobock.com...