Table of Contents
Advertisement
July 2019 – TD 304 OPERATING MANUAL – Doppler Current Profiler Sensor
SpStdev AutoBeam[cm/s]
Strength[dB]
Horizontal Speed
AutoBeam [cm/s]
Direction
AutoBeam[Deg.M]
North Beam123[cm/s]
North Beam124[cm/s]
North Beam134[cm/s]
North Beam234[cm/s]
North AutoBeam[cm/s]
East Beam123[cm/s]
East Beam124[cm/s]
East Beam134[cm/s]
East Beam234[cm/s]
Set AutoBeam Output(Off/Output) and Set NE Speed Output(Off/Output) (both set to output
to be enabled). From software version 8.2.1:
Set AutoBeam Output(Off/Output) together with Set Std Dev Speed Output(Off/Output)
Set Strength Output(Off/Output)
Set AutoBeam Output(Off/Output) and Set AutoBeam Speed
Type(Polar/Rectangular/Polar+Rectangular/Replace 4-Beam Data) set to Output and Polar
to be enabled
Set AutoBeam Output(Off/Output) and Set AutoBeam Speed
Type(Polar/Rectangular/Polar+Rectangular/Replace 4-Beam Data) set to Output and Polar
to be enabled
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).This is changed from software version 8.2.1. From this version
only Set 3-Beam Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set AutoBeam Output(Off/Output)
From software version 8.2.1:
Set AutoBeam Speed Type(Polar/Rectangular/Polar+Rectangular/ Replace 4-Beam Data)
and Set AutoBeam Output(Off/Output) set to Rectangular and Output to be enabled
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Set NE Speed Output(Off/Output) and Set 3-Beam Combination Output(Off/Output) (both
set to output to be enabled).
This is changed from software version 8.2.1. From this version only Set 3-Beam
Combination Output(Off/Output) affects the output of this parameter
Page 119
Advertisement
Table of Contents
