Hardi ALPHA EVO EcoDrive 5100 Instruction Book page 190

7 - Repair
SPN Component / Location
1322 Multiple cylinders
1323 Single cylinder
1324 Single cylinder
1325 Single cylinder
1326 Single cylinder
1327 Single cylinder
1328 Single cylinder
1346 Misfire
1450 Single cylinder
1451 Single cylinder
1638 Customer-specific sensor
1638 Customer-specific temperature
2634 Main relay
2634 Main relay
2634 Main relay
2634 Main relay
2791 EGR actuator (external)
2791 EGR actuator (external)
2791 EGR actuator (external)
2791 EGR actuator (external)
523212 CAN message
523216 CAN message
523218 CAN message
523222 CAN message
523238 CAN message
523239 CAN message
523240 CAN message
523350 Multiple injectors
523351 Multiple injectors
523352 Multiple injectors
523353 Multiple injectors
523354 ECU internal error
523355 ECU internal error
523370 Rail pressure
523420 ECU internal error
523450 Multi state switch
523451 Multi state switch
523452 Multi state switch
523470 Rail pressure limiting valve
523470 Rail pressure limiting valve
523490 ECU internal error
523500 CAN message
190
Description (Error location)
Misfire detected
Misfire detected (cylinder 1)
Misfire detected (cylinder 2)
Misfire detected (cylinder 3)
Misfire detected (cylinder 4)
Misfire detected (cylinder 5)
Misfire detected (cylinder 6)
Misfire detected with system reaction
Misfire detected (cylinder 7)
Misfire detected (cylinder 8)
Cable break or short circuit (sensor 2)
Outside target range with system reaction (temperature 2)
Short circuit to Ubatt (relay 1)
Short circuit to ground (relay 1)
Short circuit to ground or emergency shut-off (relay 2)
Short circuit to ground or emergency shut-off (relay 3)
Short circuit to Ubatt
Short circuit to ground
Cable break or ECU internal error
Cable break or short circuit
Missing (message"EngPrt" = engine protection)
Missing (message "PrHtEnCmd" = Preheat and engine command
Missing (message "RxCCVS" = cruise control)
Missing (message "TCO1" = speedo signal)
Missing (message "SwtOut" = switch outputs)
Missing or value abote target range (message "DecV1" = pseudo pedal)
Missing (message "FunModCtl" = function mode control)
Short circuit (cylinder bank 1)
Cable break (cylinder bank 1)
Short circuit (cylinder bank 2)
Cable break (cylinder bank 2)
Injector power stage A
Injector power stage B
Compression test active: Rail-pressure monitoring is going to be disabled
Watchdog counter exceeds maximum
Cable break or short circuit, input voltage outside target range (switch 1)
Cable break or short circuit, input voltage outside target range (switch 2)
Cable break or short circuit, input voltage outside target range (switch 3)
Opening failure
Opening failure with system reaction
Redundant shut-off conditions detected
Time -out of at least one sended message
FMI
11,12
11, 12
11, 12
11, 12
11, 12
11, 12
11, 12
0, 11
11, 12
11, 12
3, 4, 11, 12
2, 11
3, 11
4, 11
7, 11, 12
7, 11, 12
3, 11
4, 11
2, 5, 11
2, 3, 4, 5
11, 12
11, 12
11, 12
11, 12
11, 12
2, 12
11, 12
3, 4, 11, 13
5, 13
3, 4, 11, 13
5, 13
2, 3, 12, 14
12
11, 14
11, 14
2, 3, 4, 11
2, 3, 4, 11
2, 3, 4, 11
2, 11, 12, 14
11, 12
3, 4, 11, 12
11, 12