Multiple Station (Range) Programming; Programming Procedures; Data Dump Mode; General - Toshiba STRATA DK24 Manual

8.30 Multiple Station (Range) Programming
8.31
Some programs select options for individual
stations (where 0 0 represents the port number
being programmed). To save time, it is possible to
program all ports or a range of ports simultane-
ously.
8.32 Multiple station programming is accomplished
by substituting a range of ports (0 0 10 0) for
the port number part (0 0) of the program.
Example, all ports: w 1 111
8.33 When the multiple station range is entered,
the terminal displays existing data as follows:
Y
or
N: Data is the same for all ports in the dialed
group. Y = key/LEDs "ON"; N = key/LEDs"OFF".
U:
Key/LED is "ON" for at least one, but not all
ports in that group.
8.40 Programming Procedures
1) Refer to a completed System Record Sheet.
2) Place the terminal into the program mode per
Paragraph 7.
3) Program procedures are categorized and given
in the order below. Use these procedures to
store System Record Sheet data in working
memory.
a) Initialization procedures:
REMOTE ADMIN & MAINT PROCEDURES
SECTION 200-096-600
FEBRUARY 1991
These procedures must be completed
whenever a PCTU or PCTUSl PCB is
first installed.
.
b) Type 1 programs:
1 O-l, 1 O-2,1 O-3,15,16,42-0,77-1,77-2.
c) Type 2 programs:
Station Class of Service;
17,20,30,31,35,40,41,43,79,81 - 89.
d) Type 3 programs:
l
Initialization; 90, 92
l
General; 00, 03, 04, 05, 12,
13, 21,
22,28,29,32,33,34,36,37,38,39,
42-1 - 8, 44, 60,69, 70, 78,80,93.
l
Toll Restriction; 45 w 48.
l
Least Cost Routing; 50 w 56.
9 DATA DUMP MODE
9.00 General
9.01
This mode allows three types of data to be
displayed or output to a printer: STRATA DK Pro-
grams (Customer Data Base), Speed Dialing
Numbers (Station/System), and LCD Messages
(Station/System).
9.02 The three procedures for the Data Dump
mode are called: Program Dump, Speed Dialing
Dump, and LCD Messages Dump.
9.03 Program Dump:
While in the dump mode,
enter "PRG" and up to three characters and press
q
. The three alphanumeric characters represent
a program group or a particular program, i.e., ALL,
03, 04, 10, 39, etc. For a printout example, see
Figure 3.
CO LINE NUMBERS
40 33 32 25 24 17
81 00
11111111 11111111 11111111
81 01 00000000 00000000 00000000
81 02
00000000 00000000 00000000
81 03
00000000 00000000 00000000
81 04
00000000 00000000 00000000
81 05
00000000 00000000 00000000
81 06
00000000 00000000 00000000
t CO LINE 36
STATION PORT NUMBER
PROGRAM NUMBER
16 9
11111111
00000000
00000000
00000000
00000000
00000000
00000000
-*I :SELECT(LED
11111111
PN)
00000000
00000000
00000000
00000000
00000000
00000000
t- CO LINE 01
FIGURE 3-DATA DUMP PRINTOUT EXAMPLE
-7-