Tele System TS ULTRA 4K User Manual page 40

TELE System
NOTE
The incorrect configuration of the antenna may result in some or all channels not being loaded. If you do not know the
characteristic of your antenna system and/or you're not able to configure your receiver on your own, then consult a
trusted professional installer.
LNB configuration / Single antenna system
To configure the converter (LNB) and even in a classic single satellite antenna, enter the submenu LNB Setting and
define:
1. Satellite Name: Satellite to configure. Pressing the OK button will open the list of available satellites.
LNB Frequency
2. : Type of converter (low noise block converter - LNB) associated with the selected satellite. For
common satellite systems in Italy, the Universal (
LNB Power
3. : To disable the LNB power supply, useful in case of IF-IF type systems.
Do not enable the parameters
to switch to the channel scan menu (par. 5.3.2.2).
DiSEqC Multi-satellite antenna system
In addition to what has been described above for single satellite antenna systems, in case of DiSEqC multi-satellite
systems, in the submenu LNB Setting, set the
switch relating to the selected satellite via DiSEqC protocol. For each satellite, the user must define the correct
port/position (i.e. A,B,C or D) and respect the actual physical connection to the DiSEqC switch.
Single satellite antenna system in SCR/Unicable multi-user
For single satellite antenna systems with signal distribution in multi-user SCR/Unicable, go to the submenu
Unicable/SCR and define:
1. Satellite Name : Satellite to configure. Pressing the OK button will open the list of available satellites.
LNB Frequency
2. : Type of converter (low noise block converter - LNB) associated with the selected satellite. If it has
not been previously configurated, press OK to return to the menu LNB Setting.
User Band
3. : Number of the user corresponding to the channel assigned to the receiver/user in the SCR system.
User Frequency
4. Center frequency of the band/channel assigned to the receiver/user in the SCR system. Typical
values for interfacing with other SCR receivers are:
User Band
User Frequency
For any other frequencies, press the OK button and chose one of those available or the item
set a new one.
Transponder
5. : Verification of received signal transponder via the indicators of signal
Press OK on the item
DiSEqC 1.2 Motorized antenna system
To configure a system with DiSEqC 1.2 motorized antenna, you will have to manually move the antenna and store the
position of each satellite concerned so that the receiver can recall the correct position during the search and
broadcasting of channels. Access the submenu Motorized DiSEqC 1.2:
Satellite Name
1. : Satellite to configure. Pressing the OK button will open the list of available satellites.
Antenna Type
2. : Set on
3. LNB Setting : Type of converter (low noise block converter - LNB) associated with the selected satellite. If it has not
been previously configurated, press OK to return to the menu LNB settings.
4. Transponder : Transponder to verify the singal received via indicators of
Position command
5. : List of commands to move the motor. In particular, highlighting this item on the menu,
reference the information displayed at the bottom of the screen to move the motor. Execute the
memorize the position to associate to the satellite.
Search
Press OK on the item
USALS motorized antenna system
To configure a system with USALS type powered antenna, you will have to set the data of
through which the receiver will automatically direct the engine to the exact position of each satellite concerned so that
the receiver recalls the the correct position at a channel search or tuning. Access the submenu USALS Motor:
Satellite Name
1. : Satellite to configure. Pressing the OK button will open the list of available satellites.
Antenna Type
2. : set on
Angle/Longitude/Latitude
3.
local position (longitude and latitude).
4. LNB Setting : Type of converter (Low Noise Block converter - LNB) associated to the selected satellite. If not
previously configured, press OK to return to the menu LNB Setting.
Transponder
5. : Transponder to verify the signal received via indicators of
Position Command
6. : List of commands to move the motor towards a position of reference (zero) and towards the
position of the selected satellite. In correspondence of this item, refer to the information displayed at the bottom of
the screen to move the motor.
12
DiSEqC 1.0 DiSEqC 1.1
e
DiSEqC 1.0
1
1210
Search to go to the channel scanning menu (par. 5.3.2.2).
DiSEqC 1.2 Antenna
.
to move to the channel scanning menu (par. 5.3.2.2).
USALS Antenna
.
: Visualize/Modify the orbital position of the satellite (angle and direction) and define the
9750/10600 MHz .
) is used
and press OK on the button on the screen named
DiSEqC 1.1
or parameter which defines the converter control
2
1420
Strength
Strength
Go to Search
3 4
1680 2040
Defined by the user
Strength Quality
and
and Quality of the signal.
Save
command to
Longitude and local
Quality
and of the signal.
to
.
Latitude ,