Page 1 BBG-1022-2FS BBG-1022-2FS 3G/HD/SD-SDI Standalone Dual-Channel Frame Sync with Audio/Video Processing, AES/Analog Audio Embedding/ De-Embedding and CVBS I/O Product Manual Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com BBG1022-2FS-OM (V1.3)
Page 2 Furthermore, Cobalt Digital Inc. reserves the right to make changes to any products herein to improve readability, function, or design. Cobalt Digital Inc. does not assume any liability arising out of the application or use of any product or circuit described herein.
Page 3: Table Of Contents
Setup/Operating Instructions ......Overview ..........................3-1 BBG-1022-2FS Front Panel Display and Menu-Accessed Control ........3-1 Connecting BBG-1022-2FS To Your Network..............3-3 Finding a BBG-1022-2FS Device in DashBoard ...........
Page 4 BBG-1022-2FS Function Menu List and Descriptions ............. 3-10 Input Video Controls ................... 3-11 Output Video Mode Controls ................3-13 Framesync ......................3-15 Input Audio Status ....................3-18 Input Audio Routing/Controls ................3-19 Video Quality Events ..................3-24 Audio Detect Events Setup Controls ..............3-25 Closed Captioning ....................
Page 5: Chapter 1 Introduction
This manual provides installation and operating instructions for the BBG-1022-2FS 3G/HD/SD-SDI Standalone Dual-Channel Frame Sync with Audio/Video Processing, AES/Analog Audio Embedding/De-Embedding and CVBS I/O unit (also referred to herein as the BBG-1022-2FS). This manual consists of the following chapters: Chapter 1, “Introduction” – Provides information about this manual •...
Page 6: Manual Conventions
Manual Conventions Manual Conventions In this manual, display messages and connectors are shown using the exact name shown on the BBG-1022-2FS itself. Examples are provided below. Device display messages are shown like this: • BBG-1022-2FS Connector names are shown like this: SDI IN A •...
Page 7: Warnings, Cautions, And Notes
Symbol (WEEE 2002/96/EC) For product disposal, ensure the following: • Do not dispose of this product as unsorted municipal waste. • Collect this product separately. • Use collection and return systems available to you. BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 8: Safety And Regulatory Summary
CAUTION unauthorized sources may cause product damage, unreliable operation, and invalidate warranty. The BBG-1022-2FS FPGA is designed for a normal-range operating temperature around CAUTION 85° C core temperature. Operation in severe conditions exceeding this limit for non-sustained usage are within device operating safe parameters, and can be allowed by setting this control to Disable.
Page 9: Bbg-1022-2Fs Functional Description
Introduction BBG-1022-2FS Functional Description BBG-1022-2FS Functional Description Figure 1-1 shows a functional block diagram of the BBG-1022-2FS. The BBG-1022-2FS dual-channel frame sync provides two independent signal paths ( ) of framesync / audio embedding and de-embedding Path 1 Path 2 on a single device.
Page 10 BBG-1022-2FS Functional Description Figure 1-1 BBG-1022-2FS Functional Block Diagram BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 11: Video Processor Description
Unless otherwise noted, the following functions are independently available for Path 1 and Path 2 processing paths. The BBG-1022-2FS video subsystem provides the functions described below. Input Video Select/Quality Check Functions Used in common as a routing source for both...
Page 12 BBG-1022-2FS Functional Description 3G/HD/SD–SDI Ref VITC Frame Reference Waveform SDI VITC Detect/Extract Timecode Proc/Embed Program Video SDI VITC Input Waveform Priority/ Buffer/ ATC_VITC Detect/Extract Select Format Timecode Proc/Embed SDI ATC_VITC Detect/Extract ATC_LTC Timecode SDI ATC_LTC Proc/Embed Detect/Extract Free Run Insert...
Page 13 Introduction BBG-1022-2FS Functional Description Wings Insertion Wings insertion allows a symmetrical L-R wings insertion to be integrated into the program video output. Wings video is accommodated using a separate wings SDI input. The wings user interface displays wings timing relative to the device output video, allowing wings timing offset to be adjusted such that wings can be properly framed.
Page 14 BBG-1022-2FS Functional Description Color Corrector Option converts the YCbCr SDI input video to the 4:4:4 RGB color +COLOR space (where the color correction is applied), and then back to YCbCr SDI on the output. Controls are available to adjust each RGB level independently for both white levels (gain) and black levels (offset).
Page 15: Audio Processor Description
Introduction BBG-1022-2FS Functional Description Ancillary Data Processor This function provides full VANC/HANC ancillary data de-embedding and embedding for 3G/HD/SD-SDI streams. Direct access to DID and SDID locations allows extraction or insertion of user data such as camera PTZ, SCTE 104, closed-captioning read/insert, GPI/GPO via ANC, or other specialized user payloads.
Page 16 BBG-1022-2FS Functional Description An Input Audio Status display shows the presence and peak level of each input audio channel received by the device. In addition to SDI embedded audio channel sources, analog and coaxial AES inputs are available as input audio choices.
Page 17 Introduction BBG-1022-2FS Functional Description Audio Down Mix Function (See Figure 1-4.) The Audio Down Mixer function provides for the selection of any five embedded channels serving as Left ( ), Right ( ), Center ( ), Left Surround ( ), and Right Surround (...
Page 18: Control And Data Input/Output Interfaces
(i.e., when a preset is invoked (either manually or via event-based loading), the GPO is correspondingly also activated. Serial (COMM) Ports The BBG-1022-2FS is equipped with two, 3-wire serial ports ( COM 1 - Serial ). The ports provide for SMPTE 2020 Port 1...
Page 19: Alarm Function
The device can also be controlled using DashBoard™ remote control, where it appears as a frame connection. Technical Specifications Table 1-1 lists the technical specifications for the BBG-1022-2FS 3G/HD/ SD-SDI Standalone Dual-Channel Frame Sync with Audio/Video Processing, AES/Analog Audio Embedding/De-Embedding and CVBS I/O unit.
Page 20 Sync with Audio/Video Processing, AES/Analog Audio Embedding/De-Embedding and CVBS I/O, available in the following rear-panel I/O configurations: - BBG-1022-2FS-B (4) 3G/HD/SD-SDI Input BNCs, (4) 3G/HD/ SD-SDI Output BNCs, (1) 3G/HD/SDI Output BNC (with relay bypass failover), (1) GPIO/COMM RJ-45 connector...
Page 21 Minimum Latency (framesync disabled): SD: 127 pixels; 9.4 us 720p: 330 pixels; 4.45 us 1080i: 271 pixels; 3.65 us 1080p: 361 pixels; 2.43 us Analog Video Output Number of Outputs: One SD analog CVBS Impedance: 75 Ω 1-17 BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 22 Max V: 30 V Max P: 120 mW GPI Specifications: GPI LO @ Vin < 1.5 V GPI HI @ Vin > 2.3 V Max Vin: 9 V Redundant (or spare) AC power supply BBG-1000-PS (optional) 1-18 BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 23: Warranty And Service Information
(1) year. Cobalt Digital Inc.'s (“Cobalt”) sole obligation under this warranty shall be limited to, at its option, (i) the repair or (ii) replacement of the product, and the determination of whether a defect is covered under this limited warranty shall be made at the sole discretion of Cobalt.
Page 24: Contact Cobalt Digital Inc
Contact Cobalt Digital Inc. Contact Cobalt Digital Inc. Feel free to contact our thorough and professional support representatives for any of the following: Name and address of your local dealer • Product information and pricing • Technical support • Upcoming trade show information •...
Page 25: Chapter 2 Installation
• Installing the BBG-1022-2FS Note: • Where BBG-1022-2FS is to be installed on a mounting plate (or regular table or desk surface) without optional frame Mounting Tray BBG-1000-TRAY, affix four adhesive-backed rubber feet (supplied) to the bottom of BBG-1022-2FS in locations marked with stamped “x”. If feet are not affixed, chassis bottom cooling vents will be obscured.
Page 26: Bbg-1022-2Fs Unit Dimensions
Tighten only finger tight. Figure 2-1 Mounting BBG-1022-2FS Using Frame Mounting Tray BBG-1022-2FS Unit Dimensions Figure 2-2 shows the BBG-1022-2FS physical dimensions and mounting details for cases where BBG-1022-2FS will be installed in a location not using the optional BBG-1000-TRAY mounting tray.
Page 27 REAR Notes: 1. All dimensions in inches. 2. If BBG-1022-2FS is mounted on flat surface, either rubber feet must be installed, or mounting surface must be open to mate with cooling vents on bottom of BBG-1022-2FS chassis. Figure 2-2 BBG-1022-2FS Dimensional Details BBG1022-2FS-OM (V1.3)
Page 28 AES IN AES input BNC SDI OUT 3G/HD/SD-SDI processed out BNC CVBS OUT CVBS analog video output BNC AN-AUD OUT Analog balanced audio outputs AES OUT AES output BNC Figure 2-3 BBG-1022-2FS Rear Panel Connectors BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 29: Gpio, Serial (Comm), And Analog Audio Connections
+ and G terminals. Note that this connection will experience a 6 dB voltage gain loss. Adjust gain for these connections accordingly. – Figure 2-4 COMM, GPIO, and Analog Audio Connector Pinouts BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 30 This page intentionally blank BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 31: Chapter 3 Setup/Operating Instructions
All instructions here assume BBG-1022-2FS is physically connected to the control physical network as described in Chapter 2. Installation. BBG-1022-2FS Front Panel Display and Menu-Accessed Control Figure 3-1 shows and describes the BBG-1022-2FS front panel displays and menu-accessed user interface controls. Initial network setup is performed using these controls.
Page 32 Repeatedly press the button to step up through sub-menus and then to other menus. Access other menu items using buttons. The display backlight automatically brightens with any navigation arrow activity, and then goes dim after a few moments. Figure 3-1 BBG-1022-2FS Front Panel Display and Menu Controls BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 33: Connecting Bbg-1022-2Fs To Your Network
Note: Current IP address of BBG-1022-2FS can now be checked from the front panel by accessing this at any point. 6. At this point, BBG-1022-2FS can now be accessed with a web browser pointing to the configured address. Browse to the configured address and check connectivity.
Page 34: Finding A Bbg-1022-2Fs Device In Dashboard
Connecting BBG-1022-2FS To Your Network Finding a BBG-1022-2FS Device in DashBoard (See Figure 3-2) If BBG-1022-2FS is configured with an address within a network also available via DashBoard, a BBG-1022-2FS device appears as a frame entity in the DashBoard Basic Tree View.
Page 35: Control And Display Descriptions
This section describes the web user interface controls for using the BBG-1022-2FS. The format in which the BBG-1022-2FS functional controls appear follows a general arrangement of Function Submenus under which related controls can be accessed (as described in Function Submenu/Parameter Submenu Overview below).
Page 36: Web User Interface
In this example, the Framesync main menu tab is selected, with the overall pane now showing all sub-menu items related to the framesync function. Clicking another main menu tab immediately displays the pane related to the selected main menu tab. Figure 3-4 Typical Web UI Display and Controls BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 37: Display Theme
Setup/Operating Instructions Control and Display Descriptions Display Theme (See Figure 3-5.) The BBG-1022-2FS user interface theme selection offers light and dark themes suited for various users and environments. Clicking Settings opens a pane where the display Theme can be set With Settings open, Theme is selected to display a pallet of available themes.
Page 38: Checking Bbg-1022-2Fs Device Information
Checking BBG-1022-2FS Device Information Checking BBG-1022-2FS Device Information The operating status and software version the BBG-1022-2FS device can be checked by clicking the Status main menu tab. Figure 3-6 shows and describes the BBG-1022-2FS device information status display. Note: Proper operating status is denoted by green icons for the status indicators shown in Figure 3-6.
Page 39: Ancillary Data Line Number Locations And Ranges
ATC_VITC on line 9/8 and Dolby Metadata = 13 CC = 10 AFD (now on line 18) AFD = 18 Dolby Metadata = 13 resolved Card n Card 1 Figure 3-7 Example VANC Line Number Allocation Example BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 40: Bbg-1022-2Fs Function Menu List And Descriptions
BBG-1022-2FS Function Menu List and Descriptions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 individually lists and describes each BBG-1022-2FS function menu item and its related list selections, controls, and parameters. Where helpful, examples showing usage of a function are also provided.
Page 41: Input Video Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List Allows manual or failover selection of SDI program video inputs and displays status and raster format of received SDI video. Input Video Controls • Input Video Source/Status Selects the input video source to be applied to the device Path 1 and Path 2 program video inputs.
Page 42 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Cascaded “Serial” Dual-Path Example In this example, the dual paths are used to provide a regular program video path, as well as an identical path that imports key/ fill.
Page 43: Output Video Mode Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Allows selection of each of the four video output coaxial connectors as processed SDI out or reclocked SDI out. Also provides CVBS parameter controls and test pattern output controls for CVBS output.
Page 44 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides CVBS output parameter controls and test pattern output controls • CVBS Output Source Select Selects the processing path to be sourced for the CVBS output.
Page 45: Framesync
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides video frame sync/delay offset control and output control/loss of program video failover selection controls. Framesync Note: Framesync tab has identical independent controls for both Path 1 and Path 2 using the Path 1 / Path 2 sub-tabs.
Page 46 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Initial Startup Format Select Selects a frame sync format/rate to be invoked (from the choices shown to the left) in the time preceding stable lock to external reference.
Page 47 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Flat Field Color Select Provides a choice of flat field colors when Flat Field is invoked (either by LOS failover or directly by selecting Flat Field on the Program Video Output Mode Select control).
Page 48: Input Audio Status
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Displays signal status and payload for embedded and discrete audio received. Input Audio Status Note: Input Audio Status tab has identical independent controls/status displays for both Path 1 and Path 2 using the Path 1 / Path 2 sub-tabs.
Page 49: Input Audio Routing/Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides audio routing, gain, per-channel/bulk audio delay controls, and audio meters. These controls route selected audio sources onto the 16-channel internal bus (which is used for all audio processing).
Page 50 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Note: • Default factory preset routing routes embedded Ch 1 thru Ch 16 to bus channels Audio Bus Ch 1 thru Ch 16. • Bus Ch 2 thru Bus Ch 16 have controls identical to the controls described here for Bus Ch 1. Therefore, only the Bus Ch 1 controls are shown here.
Page 51 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Per-Channel Audio/Video Delay Offset Controls Offset control adds or reduces (offsets) channel audio delay from the matching video delay (audio delay offset setting adds or removes delay in addition to any delay included by other actions).
Page 52 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Input Flex Mix – Provides a 16-channel mixer in which each of the inputs can be mixed onto up to 16 independent output summing nodes. Each input channel has independent gain and mute controls.
Page 53 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Note: • Flex Mix input channels Flex Mix 2 thru Flex Mix 16 have controls identical to that described here for Flex Mix 1.
Page 54: Video Quality Events
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (Option +QC only) Sets quality check screening and thresholds for video quality event alerts. When a quality events occur, the event(s) can be used by the Event Setup function to invoke input routing or other changes.
Page 55: Audio Detect Events Setup Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (Option +QC only) Sets audio level screening and thresholds for audio silence/presence event alerts on embedded and/or AES discrete audio in. When an audio events occur, the event(s) can be used by the...
Page 56: Closed Captioning
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides support for closed captioning setup.Also provides controls for setting closed captioning absence and presence detection thresholds. Closed Captioning Note: • Closed Captioning tab has identical independent controls for both Path 1 and Path 2 using the Path 1 / Path 2 sub-tabs.
Page 57: Video Proc/Color Correction
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides the following Video Proc and Color Correction parametric controls. Note: Video Proc tab has identical independent controls for both Path 1 and Path 2 using the Path 1 / Path 2 sub-tabs.
Page 58 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (Option +COLOR only) Provides color corrector functions for the individual RGB channels for the program video path. • Color Corrector Color Corrector (On/Off) provides master on/off control of all Color Corrector functions.
Page 59 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Black Hard Clip Applies black hard clip (limiting) at specified percentage. (-6.8% to 50.0%; null = -6.8%) • White Hard Clip Applies white hard clip (limiting) at specified percentage.
Page 60: Output Audio Routing/Controls
Gain controls allow relative gain (in dB) control for the corresponding destination Embedded Audio Group channel. (-80 to +20 dB range in 1.0 dB steps; unity = 0 dB) Note: Although the BBG-1022-2FS can pass non-PCM data such as ® Dolby E or AC-3, setting the gain control to any setting other than default 0 will corrupt Dolby data.
Page 61 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides audio down-mix audio routing selections that multiplexes any five audio channel sources into a stereo pair. Note: • Downmixer sub-tabs offer identical independent controls for both Embedded Path 1 and Path 2. Therefore, only the Path 1 controls are shown here.
Page 62 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Output Flex Mix – Provides a 16-channel mixer in which each of the inputs can be mixed onto up to 16 independent output summing nodes. The input sources include audio bus channels from the device two embedded audio paths.
Page 63 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides an audio crosspoint allowing the audio source selection for each AES audio output channel. Also provides Gain, Phase Invert, and Muting controls and peak level meters for each output channel.
Page 64 Gain controls allow relative gain (in dB) control for the corresponding destination AES output channel. (-80 to +20 dB range in 1.0 dB steps; unity = 0 dB) Note: Although the BBG-1022-2FS can pass non-PCM data such as ® Dolby E or AC-3, setting the gain control to any setting other than default 0 will corrupt Dolby data.
Page 65 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides an audio crosspoint allowing the audio source selection for each analog audio output channel. Also provides Gain, Phase Invert, and Muting controls and peak level meters for each output channel.
Page 66 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Analog Output Channel Source Using the Source drop-down list, selects the audio input source to be routed to the corresponding analog audio output channel from the following choices: •...
Page 67: Timecode
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides timecode data extraction from various sources, and provides formatting and re-insertion controls for inserting the timecode into the output video. Timecode Note: •...
Page 68 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Audio LTC controls described below only appear on devices with +LTC licensed optional feature. This feature allows audio LTC from an audio channel to be used as a timecode source, with conversion to a selected SMPTE 12M format on the output video.
Page 69 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Source Priority Selects the priority assigned to each of the four supported external formats, and internal Free Run in the event the preferred source is unavailable.
Page 70 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Output Status Display Displays the current content and source being used for the timecode data as follows: • Output status OK (in this example, SDI VITC timecode received and outputted).
Page 71 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • HD ATC_LTC Insertion Control For HD output, enables or disables ATC_LTC timecode insertion into the output video, and selects the line number for ATC_LTC timecode data.
Page 72: Reticules
Therefore, only the Path 1 controls are shown here. Set controls for other path using the respective sub-tab. Typical Reticule/Overlay Marker Insertions The BBG-1022-2FS allows any combination of the reticule/overlay markers to be applied to the output video. Sizing and other characteristics for each type of marker can be set as described below.
Page 73 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Safe Title Area (STA) Controls • STA provides enable/disable of safe title area graticule insertion. • STA Height and STA Width control height and width of insertion (from 0% to 100% of 4:3 outputted image area).
Page 74 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Center Cross Controls • Center Cross provides enable/disable of center cross insertion. • Cross Height and Width control height of vertical line and width of horizontal line (from 0% to 100% of 4:3 outputted image area).
Page 75: Character Burner
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides user-configurable burn-in of up to two text strings and timecode on output video. Character Burner • Note: Character Burner tab has identical independent controls for both Path 1 and Path 2 using the respective Path 1 / Path 2 sub-tabs.
Page 76 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Ident Position Select Sets the location of the ident text insertion from choices shown or custom. (When Custom is selected, position is configured using the Ident Text Positioning Controls described below.)
Page 77 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Text Box Sizing Controls Provides controls for setting the size of the burn-in text background box. • Auto allows text box to proportionally size with selected text size.
Page 78 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Timecode Attributes Controls Sets burn-in size/position attributes as follows: • Character Size sets character size (in pixels). • Text Justification selects from left, right, or center-aligned justification within the text box overlay.
Page 79 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Positioning with H and V controls at zero (origin) (Size = 3) Positioning with H and V controls both at 50 (Size = 3)
Page 80: Moving Box Insertion
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides a “moving box” graphic insertion (overlay) on the output video. Moving-box insertion can serve as a dynamic raster confidence check even in cases where the input video image is static or lost.
Page 81: Y/C Alignment Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Moving Box Attributes Controls Provides independent controls for setting the color and opacity of the moving-box insertion. • Color drop-down sets box color from multiple choices shown.
Page 82: Wings Insertion
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides wings insertion/width controls and displays insertion status. Wings Insertion Note: Wings tab has identical independent controls for both Path 1 and Path 2 using the Path 1 / Path 2 sub-tabs. Therefore, only the Path 1 controls are shown here.
Page 83: Keyer
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Wings Status Displays Displays wings timing status as described below. Note: • Wings timing is a function of the wings frame sync card/ device.
Page 84 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Displays keyer timing status as described below. • Key/Fill Status Displays Note: • Key/fill timing is a function of the respective key and fill signal frame sync card/device(s).
Page 85 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Alpha Threshold keying allows cost-effective luminance keying from low-cost generic file-based graphic sources. With the graphic source applied to both the Key and Fill inputs, the Key Alpha and Key Threshold controls can be set to easily optimize the key/fill as shown below.
Page 86: Ancillary Data Proc Controls
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides controls for VANC/HANC ancillary data de-embedding and embedding to and from program video stream. Data can be extracted and inserted within the device (Bridge mode), or inserted and/or extracted to and from external interfaces via serial or IP interfaces.
Page 87 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued IP Port Setup sub-tab provides IP setup for device UDP IP communications. • Device IP Receive Setup/Status Shows device receiving IP address/status and sets port as follows: •...
Page 88 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Data-Over-Audio sub-tab provides controls that allow SMPTE 337/338/339 non-PCM data to be embedded and de-embedded on embedded audio pairs, offering a very convenient self-contained transport within the program stream physical media.
Page 89: Comm Ports Setup Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides controls for setting up the two COMM (serial) ports for LTC or ANC functions, and setting comm protocol for each port. COMM Ports Setup Controls •...
Page 90 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Insertion Sync Byte Control Allows use of a sync byte from device receiver back to sending source to synchronize communication between device receive and sending source as follows: •...
Page 91: Presets
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Allows user control settings to be saved in a Preset and then loaded (recalled) as desired, and provides a one-button restore of factory default settings.
Page 92 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Preset Save/Load Controls • Select Preset: drop-down allows a preset saved above to be selected to be loaded or deleted (in this example, custom preset “IRD Rcv122”).
Page 93: Gpo Setup Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Download (save) card presets to a Upload (open) card presets from a network network computer by clicking computer by clicking Upload Download Presets – Save at the at the bottom of bottom of the Presets page.
Page 94: Event Setup Controls
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides event-based loading allowing a defined action to be automatically engaged upon various received signal status. Actions can be “canned” control commands or user-defined by going to a user preset.
Page 95 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) In the example here for Event 1, the Video Quality Events tab is set to screen for frozen video on Input A. When detected, this status can be used here (Video Quality set to “Input A Event Engaged”...
Page 96 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) User States is a special column which allows a logic state to be set (similar to a register or latch) whenever a defined condition is first triggered. A user state (which is latched until cleared by some other definable action) can be sucessively used with other user states, thereby allowing a final action to be invoked only when subordinate user states have been sequentially satisfied as true.
Page 97 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides three general-purpose timers that can be triggered to start, pause, reset, or stop upon event actions. The state of each timer, in turn, can also be used to invoke other actions.
Page 98: Admin (Log Status/Firmware Update)
(Thermal shutdown is enabled by default). CAUTION Admin (Log Status/Firmware Update) The BBG-1022-2FS FPGA is designed for a normal-range operating temperature around 85° C core temperature. Operation in severe conditions exceeding this limit for non-sustained usage are within device operating safe parameters, and can be allowed by setting this control to Disable.
Page 99 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Firmware upgrade controls allow a selected firmware version (where • Firmware Upgrade Controls multiple versions can be uploaded to the device internal memory) to...
Page 100: User Log
BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) • Card Check and Restore Utilities Memory Test allows all cells of the card FPGA memory to be tested. This control should only be activated under direction of product support.
Page 101: Alarms Setup Controls
Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued Provides controls for setting up controls which screen for and propagate input program video alarms for video, audio, and ancillary data defect conditions. Conditions and alarm status can be propagated as Alarms Setup Controls DashBoard tree-view frame alarms, downloadable .txt...
Page 102 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Ancillary Data Alarm Setup sub-tab allows setting up screening engagement and disengagement holdoff for absence of closed captioning packets. Note: • Video screened is the card SDI that is selected for the program video/audio path.
Page 103 Setup/Operating Instructions BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Audio sub-tabs independently show for all 16 embedded channels (per path) any missing audio (whether absent due to low level, mute or unlocked status).
Page 104 BBG-1022-2FS Function Menu List and Descriptions Table 3-2 BBG-1022-2FS Function Submenu List — continued (continued) Alarm Event History shows the eight most-recent alarm events that have been detected (with most-recent at top of list). The alarm severity (as set using the Severity drop-down for each alarm type) sets the “LED” color shown here.
Page 105: Uploading Firmware Using Web Interface And Gui
Uploading Firmware Using Web Interface and GUI Firmware (such as upgrades, option keys, and presets .bin files) can be uploaded to BBG-1022-2FS directly via the web html5 interface without going through DashBoard (see Figure 3-8). In addition to allowing uploads without needing a DashBoard connection, this method transfers files typically much faster than using DashBoard.
Page 106: Front Panel User Menus
Front Panel User Menus Some of the mode and parametric controls available using the web UI (as described in BBG-1022-2FS Function Menu List and Descriptions) are available using the front panel display and arrow navigating buttons. The front panel menus offers a true standalone means to configure the device...
Page 107 Width Timecode* Height Horiz Speed Vert Speed Opacity Color Closed Captioning (pg 3-26) Output Audio Routing (pg 3-30) Input Status HD Output Line Output Meters 1-8 CC Emb/Dis Output Meters 9-16 Audio Bulk Delay 3-77 BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 108: Troubleshooting
Error and Failure Indicator Overview The BBG-1022-2FS itself and its remote control provide error and failure indications. Depending on how the BBG-1022-2FS is being used (i.e, standalone or network controlled through DashBoard™ or a Remote Control Panel), check all available indications in the event of an error or failure condition.
Page 109 Illuminates GREEN indicating signal presence for currently-selected input video path. Illuminates ORANGE if input video is lost. REF STATUS Illuminates GREEN indicating BBG-1022-2FS is receiving valid reference when set up for framesync operation. Illuminates ORANGE if reference is lost or incompatible with input video. COMM LED Illuminates GREEN when device is communicating with network connection.
Page 110: Basic Troubleshooting Checks
Basic Troubleshooting Checks Item Checks Verify power presence and • On the BBG-1022-2FS, in all cases when power is being properly supplied characteristics all indicators should be illuminated. Any device showing no illuminated indicators should be cause for concern. • Check the Power Consumed indication for the BBG-1022-2FS. This can be observed using the Status front-panel or web UI pane.
Page 111: Bbg-1022-2Fs Processing Error Troubleshooting
BBG-1022-2FS Processing Error Troubleshooting Table 3-5 provides BBG-1022-2FS processing troubleshooting information. If the BBG-1022-2FS exhibits any of the symptoms listed in Table 3-5, follow the troubleshooting instructions provided. In the majority of cases, most errors are caused by simple errors where the BBG-1022-2FS is not appropriately set for the type of signal being received by the device.
Page 112: In Case Of Problems
December 2015, your SD may not contain the recov- ery files. Contact Product Support to obtain the updated SD card containing both TTS library and SD recovery files. • If unit is a BBG-1000 Series device, remove the top cover before proceeding. 3-82 BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 113 • When reprogram is complete, LED turns off, on, and then off • again (entire process takes about 1-1/2 minute). Remove power from the card (remove card from slot or power-down BBG-1000 Series unit). 3-83 BBG1022-2FS-OM (V1.3) BBG-1022-2FS PRODUCT MANUAL...
Page 114 The Cobalt Digital Inc. Technical Support Department will continue to provide advice on any product manufactured by Cobalt Digital Inc., beyond the warranty period without charge, for the life of the product. See Contact Cobalt Digital Inc. (p. 1-20) in Chapter 1, “Introduction“ for contact information. 3-84 BBG-1022-2FS PRODUCT MANUAL BBG1022-2FS-OM (V1.3)
Page 116 Cobalt Digital Inc. 2506 Galen Drive Champaign, IL 61821 Voice 217.344.1243 • Fax 217.344.1245 www.cobaltdigital.com BBG1022-2FS-OM (V1.3) Printed in USA...

Cobalt Digital Inc BBG-1022-2FS Product Manual

Chapter 1 Introduction

Chapter 2 Installation

Chapter 3 Setup/Operating Instructions

Quick Links

Troubleshooting

Related Manuals for Cobalt Digital Inc BBG-1022-2FS

Summary of Contents for Cobalt Digital Inc BBG-1022-2FS

Table of Contents