Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Turning the touch panel on or off......... 18 Understanding the Christie touch panel interface and remote user interface... . 18 Turning the light source on or off.
CP2420-Xe • CP4420-Xe Product documentation For installation, setup, and user information, see the product documentation available on the Christie website. Read all instructions before using or servicing this product. 1. Access the documentation from the Christie website: • Go to this URL: https://bit.ly/3lkZ48l or https://www.christiedigital.com/products/projectors/cinema-projectors/.
Introduction Safety precautions Learn about the safety precautions related to the Christie CineLife+ projector.. This projector is intended for use in a cinema environment. General safety precautions Read all safety and warning guidelines before installing or operating the projector. Warning! If not avoided, the following could result in death or serious injury.
Read all safety and warning guidelines before installing the projector lamp. Warning! If not avoided, the following could result in death or serious injury. • This procedure must be performed by Christie qualified technicians. • EXPLOSION HAZARD! Always wear manufacturer approved protective safety clothing (gloves, jacket, face shield) whenever the lamp door is open or when handling the lamp.
"No direct exposure to beam shall be permitted". • The Christie Laser Projection System Installation Checklist must be fully completed after the installation and sent to lasercompliance@christiedigital.com. A copy can remain on-site. This checklist can be found as a separate document in the accessory box with the manual.
Enables connection of MPEG-2 video formats. Enables connection of MPEG-2 MXF interop video formats. Enables connection of SMPTE-compatible 2D and 3D video formats Contact Christie Technical Support to learn which S2 and S4 IMB devices are compatible with Christie projectors. Series 2 IMB video formats S2 IMB video format support is determined by the IMB make and model.
The projector can accept digital video data from HDMI sources connected to applicable IMB devices. The input configurations supported are determined by the IMB device directly. Contact Christie Technical Support to learn which IMB devices provide HDMI source selection from the projector user interface.
Re-doing this calibration is required if the following is replaced: • Color sensor board Christie recommends re-doing this calibration if any of the following are replaced: • Light engine •...
When the countdown ends, take x, y, and fL measurements using the spectroradiometer. Christie recommends taking meter readings from the center of the screen to obtain accurate screen measurements. c) Under Measured Values, using the numeric keypad record the associated spectroradiometer values for x, y, and fL.
Learn how to create new user accounts, modify the properties of those accounts, and remove the accounts. A user account is a set of credentials consisting of both a user name and password allowing access to projector settings. Default user access permissions The following table lists the Christie touch panel access permissions. Permission Description installer...
Page 66
3D encoding. • 3D Line Interleaved—The left-eye and right-eye data are sent on alternating lines. 3D Sync Input Mode is not required when using the Christie IMB. For GDC IMB devices, the recommended setting is 3D Line Interleaved. ILS File ILS file associated with the channel.
Warp files are created using an automated process through Christie Mystique. For more information on using Christie Mystique in a cinema environment, see the Mystique User Guide—Cinema Edition (P/N: 020-001240-XX). CineLife+ User Guide–CP4415-RGB, CP4420-RGB, CP4435-RGB, CP4440-RGB, CP4450-RGB, CP2420-Xe, CP4420-Xe 020-103073-06 Rev.
Page 79
Adjusting the image size and position 1. Using Christie Mystique, create the required warp file. 2. Using Mystique, upload the warp file to the projector. 3. On the projector touch panel, navigate to Image Settings > Warp File Setup. 4. To activate the warp file, find the file name in the Warp File list and select Activate.
2. If the keystone effect is severe, unevenly adjust the feet to compensate for projector tilt. Christie recommends using the lens offset to align the center of the image to the center of the screen before correcting the keystone effect.
Extreme misalignment of projection optics can cause permanent damage to critical optical components. Only Christie qualified technicians can perform internal optical adjustments. The integrator rod and fold mirror adjustments are set by Christie. Make adjustments only if screen shadows are visible.
Caution! If not avoided, the following could result in minor or moderate injury. • This procedure must be performed by Christie qualified technicians. When making the adjustments, set the light source to minimum power. To following steps are intended to achieve the highest quality image distributed across the full screen.
For the best stability, Christie recommends setting convergence while rotating the knobs in a clockwise direction. This may require first adjusting convergence by turning the knobs counter- clockwise and finalizing the convergence with a clockwise approach.
You can also create a custom macro that uses the fire alarm trigger or edit the default fire alarm macro to perform other actions as needed. Christie ACT actions The following built-in commands are available for Christie ACT. Command Description Buzzer Activates the buzzer for the specified time (in milliseconds).
(www.integpg.com). Port 9200 is the default Ethernet port for sending automation commands to the JNIOR. • The jnior login must be disabled and the jnior user name and password removed in the Christie software to allow the cues to pass over the network. •...
An upgrade package is used to upgrade the projector software to the latest version. The upgrade package is installed from a USB key or from the projector's ftpuser directory. To obtain the upgrade package, contact Christie Technical support. 1. Power on the projector and place it in Standby mode.