Page 2
Christie's control such as maintenance of the product in proper working conditions. Performance specifications are based on information available at the time of printing. Christie makes no warranty of any kind with regard to this material, including, but not limited to, implied warranties of fitness for a particular purpose.
Only trained Christie qualified technicians who are knowledgeable about the hazards associated with high-voltage, laser safety, and the high temperatures generated by the projector are authorized to assemble and install the projector. Only Christie qualified technicians are authorized to service the projector.
• CP4435-RGB Safety precautions Learn about the safety precautions related to the Christie CineLife+ 4K-RGB projector.. This projector is intended for use in a cinema environment. General safety precautions Read all safety and warning guidelines before installing or operating the projector.
Page 16
"No direct exposure to beam shall be permitted". • The Christie Laser Projection System Installation Checklist must be fully completed after the installation and sent to lasercompliance@christiedigital.com. A copy can remain on-site. This checklist can be found as a separate document in the accessory box with the manual.
Learn about the labels that may be used on the product. Labels on your product may be yellow or black and white. General hazards Hazard warnings also apply to accessories once they are installed in a Christie product that is connected to power. Fire and Shock Hazard To prevent fire or shock hazards, do not expose this product to rain or moisture.
Dealer or Christie Sales/Service contact phone number: Serial number: The serial number can be found on the license label located on the display panel. Purchase date: Installation date: Technical support Technical support for Christie Cinema products is available at: • Support.cinema@christiedigital.com • +1-877-334-4267 •...
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. Before lifting and positioning the projector, refer to the light intensity hazard distances.
Page 28
• SHOCK HAZARD! A dedicated, protected ground or earth wire must be installed on the product by Christie qualified technicians or electricians before it can be connected to power. • A certified electrician must be present during installation to ensure the installation meets the local electrical code.
Installing and setting up Disposing of the product packaging Once the product has been installed and set up, Christie recommends reusing or recycling the product packaging according to your local regulations. Completing the installation checklist Complete the provided installation checklist (P/N: 020-103137-XX) and return it to Christie.
Enables connection of MPEG-2 video formats. Enables connection of MPEG-2 MXF interop video formats. Enables connection of SMPTE-compatible 2D and 3D video formats Contact Christie Technical Support to learn which S2 and S4 IMB devices are compatible with Christie projectors. Series 2 IMB video formats S2 IMB video format support is determined by the IMB make and model.
The projector can accept digital video data from HDMI sources connected to applicable IMB devices. The input configurations supported are determined by the IMB device directly. Contact Christie Technical Support to learn which IMB devices provide HDMI source selection from the projector user interface.
Re-doing this calibration is required if the following is replaced: • Color sensor board Christie recommends re-doing this calibration if any of the following are replaced: • Light engine •...
Page 64
When the countdown ends, take x, y, and fL measurements using the spectroradiometer. Christie recommends taking meter readings from the center of the screen to obtain accurate screen measurements. c) Under Measured Values, using the numeric keypad record the associated spectroradiometer values for x, y, and fL.
Do not install or operate the projector in an inverted position. If your site has any installation requirements other than a typical theater projection booth, contact Christie for assistance. The front-to-back tilt of the projector must not exceed 15° in a downward direction or 5° in an upward direction.
Adjusting the image Christie recommends using the lens offset to align the center of the image to the center of the screen before correcting the keystone effect. 3. If one side of the image is longer than another, adjust the tilt and level of the projector.
Caution! If not avoided, the following could result in minor or moderate injury. • This procedure must be performed by Christie qualified technicians. When making the adjustments, set the light source to minimum power. To following steps are intended to achieve the highest quality image distributed across the full screen.
For the best stability, Christie recommends setting convergence while rotating the knobs in a clockwise direction. This may require first adjusting convergence by turning the knobs counter- clockwise and finalizing the convergence with a clockwise approach.