Yamaha SIGMA-G5SII Service Information page 60

6 Stoc ke r Maste r Offse t
Master nozzle:PM01, Auto Hight Level:JG0297(Hsp/Odd)/0298(MF)
Operation: Debug mode
①Select Menu Ship.Adj 〉Stk Master
②Select Block # > Stocker # > H:Hsp O:Odd M:MF
③Please set Auto Hight LeveJIG onto the select Stocker position.
Then Press 「Teach Start」
7 Fe e de r A Offse t／L： UP/ DN（ HSP He ad）
①Set Nozzle onto the Head 1 nozzle pos.1 and the Auto height Calibration
JIG on the Feeder slot No. 101. (Feeder Base 1)
②Select MENU Ship.Adj. >Pick-up Lv >Des Fdr >101-102
Then press [Teach Start]
Caution：Please make sure, Do not leave any
unnecessary insturumens on the Feeder Base.
③Please perform Feeder A offset teach for
Feeder 121-140 and 141-160 area
by same procedure of ②
④Please teach the Feeder Base A teach 101-120 ,121-140 ,141-160
Offset by Head 2.
⑤Please teach the offset for Feeder base 2 by same procedure of Feeder Base 1
8 PEC Re c og / Be am Offse
① Slect MENU Ship.Adj. >PEC Recog. Beam
② Select Beam ==> ALL
(If need , you can select Head 1 or 2. )
Grass jig : Not use
9 Comporn e n t Re c og Came ra Position Offse t
① Slect MENU Ship.Adj. >Cmp Recog Camr Pos
② Select Head ==> ALL or Head 1 or Head 2
* Set the Glass QFP Jig on the machine.
* Set the Nozzle HA09C on the head.
1 0 He ad c e n te r / Mark Position Offse t
① Slect MENU Ship.Adj. >Hd Rot Center
② Select Head ==> ALL or 1 or 2
③ Select Camera ==> ALL or 1 or 2
④Select [Head Cntr] button
Press [Teach Start]
1 1 He ad c e n te r / Mark Position Offse t
① Slect MENU Ship.Adj. >Hd Rot Center
② Select Head ==> ALL or 1 or 2
③ Select Camera ==> ALL or 1 or 2
④Select [Head Cntr] button
Press [Teach Start]
Service Information
Stocker Master
H1
H2
Feder
F101-120
F121-140
F141-160
F201-220
JG-0342 F221-240
F241-260
CAM １ Before
MAG.X
MAG.Y
.Z deg
Pos.X
Pos.Y
X deg
Y deg
Rect.X
Pos.X
deg
X
CAM １
Y
Z
X
CAM 2
Y
Z
H IGH SPE E D H E A D
Mul ti F uncti on H ea d
H IGH SPE E D H E A D
X
CAM 1
Y
X
CAM 2
Y
SI1705004E-00=SIGMA-G5SII Service Manual
60/273
For Service Engineer
Before
ＳＴ1
ＳＴ2
ＳＴ3
ＳＴ4
ＳＴ1
ＳＴ2
ＳＴ3
ＳＴ4
Head 1 Head 2
Before After Before
After CAM 2 Before
MAG.X
MAG.Y
.Z deg
Pos.X
Pos.Y
X deg
Y deg
Rect.X
---
Pos.X
deg
Head 1 Head 2
Before After Before
Before
H1
H2
Before
N1
N3
Head 1 Head 2
Before After Before
After
After
After
---
After
After
After
After