Yamaha SIGMA-G5SII Service Information page 59

SIGMA-G5SII Instllation check sheet
A
T ype
Tr an sfe r Single tranfer
P CB Flo w L→R
P C
R Front
B
He ad Type H1 HSP
Tr ay Fe e de r H１
S o ft Ve r ： sw1：
Ho st Name ：
S abn e t mask：
Ac v S e r ve r ：
1 Machine Level
Please Fill in the result of split level gauge ( Split Level 1 & 2 )
Level ①
水準器①
Level ③ 水準器③
2 Warm Up
Check the machine level gauge differences value less than 0.02mm (2 scale) ,
Before and after Warm-up (Aging) the machine 2hours.
If the machine level is over the limit , Adjust the level again.
3 NL-Axis Origin /Master nozzle Level offset
Sys.Setting＞Offset Data＞Head＞Head offset
Please make a note current NL axis Origin offset then clear and save.(Zero)
Perform the NL -Orign offset teach
Maint＞Ship Adj＞NL Origin /Master nozzle offset
4 Head UP/ DN OFFSET（HSP ・MF ）
①Set the Conveyor Width 80mm, Clearlance 0.8mm
②Set the JIG Plate onto middle of a conveyor, Then clamp the JIG by Z-clamp
[MENU] Maint.> DVC Check >OutP Chk> XFR > CNVR >
Slect [D1] & [D3] ==> Ascent (Clamp)
Slect [D0] & [D2] ==> Decent (Clamp)
③ Apply the master nozzle onto the head nozzle position
(No1 Nozzle position is 12:00 direction when DD-axis is original position)
④ Perform Head UP/DN Offset
[MENU] Ship.Adj > Placement Lv > Slect Head > Teach Start Then press Move
5 Chute Level Offset （Factory Ship.）
① Please set JIG nozzle onto the Head 1 nozzle pos. 1
② Select the menu Ship.Adj > Chute Lv > Select Head 1.
Then Press 「Teach Start （Shipment)」
* Do not perform 「Teach Start （exchange)」
B C D E
Dual transfer
R→L K e ybo r ad Front
L Rear L Front R Rear
MF H2 HSP
H2 NoneCo pr a. H1 H2
sw2：
I P Addr e ss：
De fau lt gat way：
LI S A：
Level ②
水準器②
１目盛=0.02mm
0.02mm/Scale
[Target ]
Within±0.02mm
for each .
Then Press [ON]
Then Press [ON]
59/273
Service Information
F Work Started
Work Ended
Customer
Rear
S/N
MF Line
Engineer
None
N ozzl e Stock er La y out
Stocker #1
Stocker #2
Stocker #3
Stocker #4
No.
Level gauge ①
Level gauge ②
Level gauge ③
Input convyer hight
Output convyer hight
NL-Axis Org/master
NL-Axis Orign
H1
Master Nozzle
NL-Axis Orign
H2
Master Nozzle
H IGH Speed H ea d
Head UP/DN
H1
H2
Mul ti F uncti on H ea d
Head UP/DN
H1
H2
H IGH Speed H ea d
Chute Level
H1
H2
Mul ti F uncti on H ea d
Chute Level
H1
H2
SI1705004E-00=SIGMA-G5SII Service Manual
For Service Engineer
CS1705002E-000 (ver.1600)
Date: Time:
Date: Time:
(*H：HSP O：ODD M：MF)
Block 1 Block 2
H O M H O
H H
H H
H O M H O
Level Tool Lot No.
mm MR
mm MR
mm MR
C h e c k (Aft e r W ar m Up)
Before After
Before After
Before After
N1
N3
N1
N3
Before After
Before After
N1
N3
N1
N3
M
M
mm
mm