Advertisement
CHAPTER 1 CONTROLLER
CHAPTER 1 CONTROLLER
5. 5.7 7
Set t u u p p O O p p ti tion
Se
Option
Option
# #
# # 4 4 0 0
T T r r u u c c k k T T y y p p e e
# # 4 4 1 1
B B a a t t t t e e r r y V
# # 4 4 2 2
B B a a t t t t e e r r y y T T y y p p e e
Hydraulic Control
Hydraulic Control
#43
#43
Selection
Selection
# # 4 4 4 4
M M a a s s t t T T y y p p e e
# # 4 4 5 5
V V a a l l v v e e S S e e c c t t i i o o n n
Battery Voltage
Battery Voltage
#46
#46
Adjustment
Adjustment
# # 4 4 7 7
F F o o o o t t D D i i r r e e c c t t i i o o n n
# # 4 4 8 8
L L o o a a d d M M e e t t e e r r F F u u n n c c t t i i o o n n
# # 5 5 0 0
T T i i l l t H
#51 1
#5
T T il ilt t Ho
# # 5 5 5 5
L L o o a a d A
Note:
Note:
(1) The data of a g
(1)
The data of a group 3 has no defa
aren't in agreement, the truck does not operate normally.
aren't in agreement, the truck does not operate normally.
(2)
(2) When you set up
When you set up for the first
(3)
(3) If SUO d
If SUO data is not s
(4) This value was adju
(4)
This value was adjusted at the tim
different from actual battery voltage.
different from actual battery voltage.
ons s (G
(Gro rou u p p 3) 3)
T T i i t t l l e e o o f f O O p p t t i i o o n n
This option is u
This option is used to set
the truck.
the truck.
This option is used
This option
y Vo o l l t t a a g g e e
of the battery.
of the battery.
This option is u
This option is used to set
the battery.
the battery.
The electric d
The electric discharge charact
of a battery changes with
of a battery changes with battery
type.
type.
This option is used to set
This option is u
the hydraulic control
the hydraulic control
This option is used to set
This option is u
the mast.
the mast.
This option is used to set the
This option is used
number of valve sections.
number of valve sections.
This setting corrects the gap
This setting corr
battery voltage which the controller
battery voltage which the controller
recognizes, and actual battery
recognizes, and actual battery
voltage.
voltage.
Measure actual battery voltage and
Measure actual battery voltage and
operate the direction lever in
operate the direction lever in order
to adjust the value which is shown
to adjust the value which is shown
on the service tool actual battery
on the service tool actual battery
voltage.
voltage.
This option is used t
This option is used to enable the
function for foot direction option.
function for foot direction option.
Armrest FNR
Armrest FNR
This option
This option is used
the load meter.
the load meter.
t Ho o r r i i z z o o n F
n Fu u nc
nct t i i o o n n
This option is used
This option
the tilt horizon function.
the tilt horizon function.
When the #50 "Tilt horizon function "
When the #50 "Tilt horizon function "
is enabled, this option is used to
is enabled, this option is used to
Hor r iz izo o n n Ad
Adju just stm m e e nt nt
store the analog value when the
store the analog value when the
mast is positioned horizontally.
mast is positioned horizontally.
When the #48 "Load Meter" is
When the #48 "Load
enabled, this option is used to store
enabled, this option is used to store
d Ad d j j u u s s t t m m e e n n t t
the analog value when the live load
the analog value when the live load
is zero.
is zero.
roup 3 has no default value, but it nee
ult value, but it needs to set data
for the first time, set up th
time, set up the group 3 fir
ata is not set, th
et, the erro
e error code "
r code "62" is disp
62" is displayed
sted at the time of LOGIC
e of LOGIC CARD inspection. Adju
D D e e s s c c r r i i p p t t i i o o n n
sed to set the type of
the type of
0: 3-Wheel model
0: 3-Wheel model
1: 4-Wheel model
1: 4-Wheel model
is used to set
to set the voltag
the voltage e
3 3 6 6 , , 4 4 8 8 [ [ V V ] ]
sed to set the type of
the type of
0: Normal BDI
0: Normal BDI
ischarge characteristic
eristic
1: Tubular BDI
1: Tubular BDI
battery
2: Gel BDI
2: Gel BDI
sed to set the type of
the type of
0: FC specification
0: FC specification
1: MC specification
1: MC specification
2FF: 2-stage full-free
2FF: 2-stage full-free
sed to set the type of
the type of
3FF: 3-stage full-free
3FF: 3-stage full-free
2SP: 2-stage panorama
2SP: 2-stage panorama
to set the
1: 3 ways (lift, tilt, attachment 1)
1: 3 ways (lift, tilt, attachment 1)
2: 4 ways (lift, tilt, attachment 1,2)
2: 4 ways (lift, tilt, attachment 1,2)
ects the gap of the
of the
5 5 . . 0 0 t t o o 1 1 2 2 0 0 . . 0 0 [ [ V V ] ]
order
o enable the
1: Standard direction lever
1: Standard direction lever
2: Foot Directional Control (FoDiCo)
2: Foot Directional Control
3: Armrest FNR
3: Armrest FNR
is used to enable
to enable/disable
/disable
0: Disable
0: Disable
1: Enable
1: Enable
is used to enable
to enable/disable
/disable
0: Disable
0: Disable
1: Enable
1: Enable
0 to 255
0 to 255
Meter" is
0 to 255
0 to 255
ds to set data by the actual tru
by the actual truck type. If the value
e group 3 first, and then set
st, and then set default data of g
default data of group 1 and 2.
layed. .
CARD inspection. Adjust the value if t
st the value if the value shown on
R R a a n n g g e e
(FoDiCo)
ck type. If the value and the truck
and the truck model
roup 1 and 2.
he value shown on the service t
the service tool is
1-37
1-37
Default
Default
Value
Value
– –
– –
– –
– –
– –
– –
– –
– –
model
ool is
Advertisement
