Related Manuals for Mitsubishi FBC15N
Summary of Contents for Mitsubishi FBC15N
- Page 1 Service Manual Controller FBC15N A4BC1-10200-up FBC18N A4BC1-20200-up FBC18LN A4BC1-30200-up FBC20N A4BC2-10200-up FBC25EN A4BC3-20200-up FBC25N A4BC2-20200-up FBC25LN A4BC3-30200-up FBC30N A4BC3-40200-up FBC30LN A4BC4-10200-up 99759-7C110...
- Page 2 The descriptions, illustrations and specifications contained in this manual are of the trucks with the serial numbers in effect at the time it was approved for printing. Mitsubishi forklift truck reserves the right to change specifications or design without notice and without incurring obligation.
- Page 3 Do not operate this truck unless you have read The proper and safe lubrication and maintenance and understand the instructions in the for this forklift truck, recommended by Mitsubishi OPERATION & MAINTENANCE MANUAL. forklift truck, are outlined in the OPERATION &...
- Page 4 19. Tighten connections to the correct torque. Make 10. Always use tools that are in good condition and be sure you understand how to use them before sure that all heat shields, clamps and guards are performing any service work. installed correctly to avoid excessive heat, vibration or rubbing against other parts during operation.
-
Page 5: How To Use This Manual
HOW TO USE THIS MANUAL (Removal, Installation, Assembly and Disassembly) Disassembly diagram (example) Procedures are described in the text. Disassembling sequence 209603 Sequence 1 Cover , Bolt, Washer (part name) (part name) 2 Snap ring ....Suggestion for disassembling 1. Output shaft, Removing Remove output shaft using a special tool. - Page 6 Symbols or abbreviation Option R1/4 Taper pipe thread (external) 1/4 inch (formerly PT1/4) Rc1/8 Taper pipe thread (internal) 1/8 inch (formerly PT1/8) G1/4A Straight pipe thread (external) 1/4 inch (formerly PF1/4-A) Rp1/8 Straight pipe thread (internal) 1/8 inch (formerly PS1/8) Units 1.
- Page 7 GROUP INDEX GROUP INDEX Items Controller system, Controller features, Setup option, Diagnosis, Removal and CONTROLLER installation, Basic check TROUBLESHOOTING Faulty central vehicle monitor system, Faulty diagnosis indication, FOR CONTROL or Other abnormalities CIRCUITS Motor installation positions, Specifications, Structures, Tightening of high-power MOTORS cable terminals, Procedures and suggestions for removal and installation, Procedures and suggestions for disassembly and reassembly...
- Page 8 CONTROLLER Controller System ..................1 – 1 System Configuration ................1 – 1 Controller Area Network (CAN) ..............1 – 3 Outline of Controller ................. 1 – 5 Controller Features ................. 1 – 8 Traction Control Features ................. 1 – 8 Lifting Control Features ................
-
Page 9: Basic Check
Basic Check ..................... 1 – 57 Testing Tools ..................... 1 – 57 Measurement of Card Voltage ..............1 – 58 Checking Contactor Coil ................1 – 61 Checking Contactor Tip ................1 – 61 Checking Inverter ..................1 – 62 Regeneration Check ................. -
Page 10: Controller System
CONTROLLER Controller System System Configuration The logic unit and the inverter are linked together by The truck is controlled by the logic unit and the inverter. the Controller Area Network (CAN) to communicate with each other. The logic unit sends the motor control The system configuration is classified into two types command to the inverter and the inverter sends the according to the lifting control system: the Contactor... - Page 11 CONTROLLER System Configuration for Transistor Control Type Input switch signals RS232C Key switch Display Direction lever Logic Unit Accelerator Logic card Service brake Warning buzzer Parking brake Traveling control Lifting control Contactor control signal Seat switch Safety function Seat belt switch Lift lock solenoid control signal etc.
- Page 12 BUY NOW Then Instant Download the Complete Manual Thank you very much! ...