Related Manuals for Nexcom ISA 140
Summary of Contents for Nexcom ISA 140
- Page 1 NEXCOM International Co., Ltd. Network and Communication Solutions Industrial-Grade Platform ISA 140 User Manual NEXCOM International Co., Ltd. www.nexcom.com Published January 2022...
-
Page 2: Table Of Contents
Knowing Your ISA 140 ................3 Mechanical Dimensions ................4 Removing the Bottom Chassis Cover .............15 Installing an M.2 SSD Storage Module ..........16 Installing SO-DIMM Memory Modules ...........18 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 3 Default Configuration ................25 Entering Setup ..................25 Legends ....................25 BIOS Setup Utility ..................27 Main ....................27 Advanced ..................28 Chipset ....................37 Security .....................41 Boot ....................42 Save & Exit ..................43 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 4: Preface
Acknowledgements The product(s) described in this manual complies with all applicable ISA 140 is a trademark of NEXCOM International Co., Ltd. All other product European Union (CE) directives if it has a CE marking. For computer systems names mentioned herein are registered trademarks of their respective owners. -
Page 5: Rohs Compliance
0.1% or 1,000ppm, and Polybrominated diphenyl Ethers (PBDE) < 0.1% or 1,000ppm. In order to meet the RoHS compliant directives, NEXCOM has established an engineering and manufacturing task force in to implement the introduction of green products. The task force will ensure that we follow the standard... -
Page 6: Warranty And Rma
(manuals, cable, etc.) and any components from the card, such as CPU and RAM. If the components were suspected as part of the problems, ▪ If RMA goods can not be repaired, NEXCOM will return it to the customer please note clearly which components are included. Otherwise, NEXCOM without any charge. - Page 7 ESD workstation. If no such station is available, you can provide some ESD protection by wearing an antistatic wrist strap and attaching it to a metal part of the computer chassis. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 8: Safety Information
There is a danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Discard used batteries according to the manufacturer’s instructions. viii Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 9: Safety Precautions
RECOMMENDED BY THE MANUFACTURER. DISCARD USED BATTERIES ACCORDING TO THE MANUFACTURER’S INSTRUCTIONS. 10. All cautions and warnings on the equipment should be noted. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 10: Technical Support And Assistance
Preface Technical Support and Assistance Conventions Used in this Manual 1. For the most updated information of NEXCOM products, visit NEXCOM’s Warning: website at www.nexcom.com. Information about certain situations, which if not observed, can cause personal injury. This will prevent injury to yourself 2. -
Page 11: Global Service Contact Information
16F, No.250, Sec. 2, Chongde Rd., Beijing, 100094, China Beitun Dist., Tel: +86-10-5704-2680 Taichung City 406, R.O.C. Fax: +86-10-5704-2681 Tel: +886-4-2249-1179 Email: sales@nexsec.cn Fax: +886-4-2249-1172 www.nexsec.cn Email: sales@nexaiot.com.tw www.nexaiot.com.tw Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 12 Room 603/604, Huiyinmingzun Plaza Bldg. 1, Tel: +81-3-5419-7830 No. 609, Yunlin East Rd., Fax: +81-3-5419-7832 Shanghai, 200062, China Email: sales@nexcom-jp.com Tel: +86-21-5278-5868 www.nexcom-jp.com Fax: +86-21-3251-6358 Email: renwang@nexcom.com.tw www.nexcom.cn Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 13: Package Contents
Preface Package Contents Before continuing, verify that the ISA 140 package that you received is complete. Your package should have all the items listed in the following table. Item Item Number Name T601-0000015806 (N)EPE For ISA140 Ver:A Both Squerity 230x170x102mm... -
Page 14: Ordering Information
Preface Ordering Information The following below provides ordering information for ISA 140. Barebone ISA 140 (P/N: 10L10014000X0) Intel Atom ® x6212RE (Elkhart Lake) processor, with 6 x 1GbE RJ45 with 1 x bypass pair Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. -
Page 15: Chapter 1: Product Introduction
▪ Storage eMMC up to 8GB for OS ▪ 1 x Minicard full size with PCIe & USB signal ▪ Storage M.2 Key B slot, supports 2242 for data storage ▪ Supports OOB Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 16: Hardware Specifications
▪ 4 x SMA antenna holes ▪ CE/FCC Class A ▪ 2 x USB 3.0 Interface Internal ▪ 1 x DDR4 SODIMM slot ▪ 1 x M.2 2242 Key B slot Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 17: Knowing Your Isa 140
Used to connect a high-definition display. 9V to 36V DC Power Inputs Used to plug a DC power cord. HDMI LAN0 RJ 45 Console 9V~36V DC Input LAN2 and LAN4 Reset Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 18: Mechanical Dimensions
Chapter 1: Product Introduction Mechanical Dimensions 175.00 61.70 59.70 174.10 165.00 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 19: Chapter 2: Jumpers And Connectors
Static electricity can damage many of the electronic ▪ Use correct screws and do not over tighten screws. components. Humid environments tend to have less static electricity than Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 20: Jumper Settings
(on) and open (off). Two-Pin Jumpers: Open (Left) and Short (Right) Three-Pin Jumpers: Pins 1 and 2 are Short Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 21: Locations Of The Jumpers And Connectors
The figure below is the top view of the main board used in the system. It shows the location of the jumpers and connectors. BIOS_J1 LAN2 LAN1 CON1 LED3 LED9 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 22 Chapter 2: Jumpers and Connectors The figure below is the bottom view of the main board used in the system. U51 SOC CPU Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 23: Jumpers
Connector type: 1x3 3-pin header, 2.54mm pitch Connector type: 1x5 5-pin header, 2.54mm pitch Connector location: JP1, JP3 Connector location: JP2 Definition Definition MCU1_NMCLR VDD_MCU Definition MCU1_PGED SRTC_RST_N MCU1_PCEC Definition RTC_RST_N Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 24: Connector Pin Definitions
PV5_USB30 USB2N0_C HDMI_DATA2_P_C USB2P0_C HDMI_DATA2_N_C HDMI_DATA1_P_C USB3RN0_C USB3RP0_C HDMI_DATA1_N_C USB3TN0_C HDMI_DATA0_P_C USB3TP0_C PV5_USB30 HDMI_DATA0_N_C HDMI_CLK_P_C USB2N1_C USB2P1_C HDMI_CLK_N_C USB3RN1_C USB3RP1_C HDMI_CLK HDMI_DAT USB3TN1_C USB3TP1_C P5V_HDMIC HDMI_HPD_C Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 25: Internal Connectors
M.2 B-Key LTE M.2 B-Key SATA Connector location: CN4 Connector location: CN1 Definition Definition Definition M2_RX_DP PCIE_LTE_RXN UIM1_RESET M2_RX_DN PCIE_LTE_RXP UIM1_CLK M2_TX_DN PCIE_LTE_TXN UIM1_DATA M2_TX_DP PCIE_LTE_TXP UIM1_PWR Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 26: Mini Pcie Slot
Mini PCIe Slot Power and Reset Connector location: CN2 Connector location: SW1 Definition Definition Definition Definition PCIE_CLK3_DN PCIE_CLK3_DP WIFI_RXN WIFI_RXP FP_PWRBTN_N_R WIFI_TXN WIFI_TXP SYS_RESET_N_R USB2_P2_DN USB2_P2_DP Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 27: Micro Sim Connector
Chapter 2: Jumpers and Connectors Micro SIM Connector Connector location: CN7 Definition Definition UIM1_VCC UIM1_RESET UIM1_CLK UIM1_D0 UIM1_VPP UIM1_DATA SIM_DET Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 28: Block Diagram
1512 1512 1512 1 pair bypass 2 (1512, TSN) 0 (OOB) 1 (TSN) 3 (i210) 2xUSB3.0 6x 1GbE RJ45 include 1x OOB port RJ45 Console HDMI Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 29: Chapter 3: System Setup
1. The screws on the bottom cover are used to secure the cover to the chassis. Remove these screws and put them in a safe place for later use. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 30: Installing An M.2 Ssd Storage Module
To install an M.2 SSD module, please follow the instructions below. 1. Remove the four screws from the side cover, and the three screws from the board. M.2 SSD slot Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 31 4. With the module fully inserted, tighten a screw into the mounting hole on the module to secure it. Screw Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 32: Installing So-Dimm Memory Modules
SO-DIMM socket. Push the module down until the clips on both sides of the socket lock into position. The gold-plated connector on the edge of the module will almost completely disappear inside the socket. SO-DIMM Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 33: Installing A Wireless Lan Module
LAN module. To install the module, please follow the instructions below. 1. With the bottom cover removed, locate the mini-PCIe slot on the mainboard. mini-PCIe slot Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 34 Ring 1 Ring 2 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 35: Installing A Lte Module
LTE module. Only one can be installed at a time. 1. With the bottom cover removed, locate the mini-PCIe slot on the mainboard. mini-PCIe slot Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 36 Ring 1 Ring 2 Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 37: Installing A Sim Card
Insert the SIM card and secure the SIM card cover after installation. 1. The SIM card socket is located on the right side of the system. SIM Socket Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 38: Chapter 4: Bios Setup
This chapter describes how to use the BIOS setup program for ISA 140. The The settings made in the setup program affect how the computer performs. BIOS screens provided in this chapter are for reference only and may change if It is important, therefore, first to try to understand all the setup options, and the BIOS is updated in the future. -
Page 39: Default Configuration
Powering on the computer and immediately pressing <Del> allows you to enter Setup. Load optimized default values. Press the key to enter Setup: Saves and exits the Setup program. Press <Enter> to enter the highlighted sub-menu Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 40 When “” appears on the left of a particular field, it indicates that a submenu which contains additional options are available for that field. To display the submenu, move the highlight to that field and press Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 41: Bios Setup Utility
Enter: Select +/-: Change Opt. F1: General Help F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.21.1278 Copyright (C) 2021 AMI Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 42: Advanced
F4: Save & Exit ESC: Exit Active Processor Cores Select the number of cores to enable in each processor package. Version 2.21.1278 Copyright (C) 2021 AMI Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 43 Enters the CPU - Power Management Control sub-menu. Enables or disables Intel SpeedStep technology. C states Enables or disables CPU C states support for power saving. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 44 Version 2.21.1278 Copyright (C) 2021 AMI Firmware Update Configuration Me FW Image Re-Flash Enters the Firmware Update Configuration submenu. Enables or disables the ME firmware image re-flash function. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 45 Intel(R) TCC mode is enabled. SHA-1 PCR Bank Enables or disables SHA-1 PCR Bank. SHA256 PCR Bank Enables or disables SHA256 PCR Bank. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 46 Version 2.21.1278 Copyright (C) 2021 AMI note that some HCK tests might not support 1.3. Super IO Chip Displays the Super I/O chip used on the board. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 47 Selects an optimal setting for the Super IO device. System temperature Detects and displays the current system temperature. +VCCIN to +VCCIO_CPU Detects and displays the +VCCIN and +VCCIO_CPU voltage. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 48 Selects the serial port transmission speed. The speed must match the other side. Long or noisy lines may require a lower speed. Data Bits The options are 7 and 8. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 49 Selects the Putty keyboard emulation type. XHCI Hand-off This is a workaround for OSs that does not support XHCI hand-off. The XHCI ownership change should be claimed by the XHCI driver. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 50 F2: Previous Values F3: Optimized Defaults F4: Save & Exit ESC: Exit Version 2.21.1278 Copyright (C) 2021 AMI Network Stack Enables or disables UEFI network stack. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 51: Chipset
Access SD device in DMA mode if controller support it, otherwise in PIO mode. DAM Option Access SD device in DMA mode. PIO Option Access SD device in PIO mode. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... - Page 52 F4: Save & Exit ESC: Exit ESC: Exit Version 2.21.1278 Copyright (C) 2021 AMI Version 2.21.1278 Copyright (C) 2021 AMI VT-d Enables or disables the VT-d. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 53 Restore AC Power Loss Settings for PCI Express root port 1, 2, 3 and 7. Select the AC power state when power is re-applied after a power failure. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
- Page 54 PCI Express Root Port 1, 2, 3 and 7 PCIe Speed Settings for PCI Express root port 1, 2, 3 and 7. Configures the speed of the PCI Express Root Port. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
-
Page 55: Security
Version 2.21.1278 Copyright (C) 2021 AMI Version 2.21.1278 Copyright (C) 2021 AMI SATA Controller(s) Administrator Password Enables or disables the SATA controller. Select this to reconfigure the administrator’s password. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 56: Boot
NumLock on wherein the function of the numeric keypad is the number keys. When set to Off, the function of the numeric keypad is the arrow keys. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual... -
Page 57: Save & Exit
<Enter>. You may be prompted to confirm again before exiting. Restore Defaults To restore the BIOS to default settings, select this field then press <Enter>. A dialog box will appear. Confirm by selecting Yes. Copyright © 2022 NEXCOM International Co., Ltd. All Rights Reserved. ISA 140 User Manual...
Need help?
Do you have a question about the ISA 140 and is the answer not in the manual?
Questions and answers