Vidicode V-Tap ISDN PRI Manual
  1. Manuals
  2. Brands
  3. Vidicode Manuals
  4. Recording Equipment
  5. V-Tap ISDN PRI
  6. Manual

Vidicode V-Tap ISDN PRI Manual

Hide thumbs Also See for V-Tap ISDN PRI:
Table of Contents

Advertisement

Quick Links

Download this manual
V-Tap ISDN PRI
Manual
v1.23
V-Tap ISDN PRI Manual EN v1.23 Nov 2021
© 2018-2021 Vidicode
1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the V-Tap ISDN PRI and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Vidicode V-Tap ISDN PRI

Summary of Contents for Vidicode V-Tap ISDN PRI

  • Page 1 V-Tap ISDN PRI Manual v1.23 V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 2: Table Of Contents

    3.3.10 Licenses & Versions .............. 28 LED’s ................29 Red Error LED ..............29 Green Link LED ..............30 Blue Data LED ..............31 Amber SD-Power LED ............. 31 V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 3 Remote control with UDP commands ..... 45 D-channel trace for debug........47 ISDN PRI RJ45 connectors & wiring ......48 Revision History ............49 Acknowledgements ..........50 14.1 Privacy ................50 14.2 Liability ................50 V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 4: Introduction

    The LAN cable must be connected to the Ethernet port, which is 100 Mbps Full Duplex. The V-Tap ISDN PRI is a member of a family of compatible products that can be used to create all sorts of recording solutions. There are V-Taps for VoIP, Analog, Audio, Audio and ISDN telephony and there is a V-App for mobile recording.

  • Page 5: Getting Started

    2 Getting started 2.1 Hardware installation The V-Tap ISDN PRI is easy to setup. The following steps are involved: • The jumpers inside must be set to the right mode; default on Sniff. • Connect the Trunk and PBX to the ISDN ports of the V-Tap.

  • Page 6: Sniff Mode Operation

    DTMF **. In Pass-Through mode, the V-Tap PRI can only be connected as In-Line. The 7 jumpers must be placed as follows for Pass-Through mode: V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 7: Parallel Connection

    The advantage of connecting In-Line is, that the V-Tap cannot be removed without notice, because the ISDN line will be interrupted when doing so. In-Line connection is shown below: V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 8: Software Installation

    System settings, Network tab and enable “V-Tap” as is shown below: NOTE1: Apresa’s IP address is the “Tunnel Server Address” in the V-Tap. NOTE2: Be sure the Encryption password is the same as in the V-Tap unit. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 9: V-Archive Software On A Pc

    NOTE4: The V-Archive software itself does not need licenses to receive from the V-Tap. Licenses are inside the V-Tap. The V-Archive software for the PC is further not described in this manual; see for more details the V-Archive manual. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 10: Checklist For Tunnel Connection

    Tools, System. 10) The SD card in the V-Tap should contain “.WAV” files. This SD card can be read by the V-Archive software in menu File and ‘Import from V-Tap’. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 11: Web Interface And Settings

    1 second. The LED’s will flash shortly and the V-Tap can be accessed on the IP address 192.168.55.66 See also Disable DHCP temporary Show IP address. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 12: Web Interface

    Now enter “admin” for the Username and “admin” for the Password, then press the Login button and the Settings page appears: (The settings on the next page are not the default settings, but just an example.) V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 13 By pressing the Save & Logout button, the settings are sent to the V-Tap unit. Any ongoing recording is stopped, the file on SD card is closed, and after a few seconds the new settings are activated. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 14: Settings

    V-Tap and the computer connecting to it. The default mask is 255.255.255.0. In case DHCP is used, the mask is automatically obtained. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 15 The default DNS address 8.8.8.8 is the Google Public DNS, but the Gateway must be defined also before this address is reachable. In case DHCP is used, the DNS address is automatically obtained. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 16: Tunnel Settings

    Tunnel stream must be setup right. Firewalls must have a rule to let through TCP port 2016. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 17: Special Tunnel & Network Settings

    It is therefore not recommended to select a fixed number for the Tunnel Source Port in cases where live streaming is done without using an SD card. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 18 The values 50 and 18 (same as 0) can be used for faster sending. NOTE: When using the RTR Call Monitoring Software for the PC, the LAN Service Timer must be set to 1 to get a constant audio stream. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 19: Wi-Fi Settings

    All further access must then be done through a LAN cable. Sending tunnel data with Wi-Fi is slower than using a LAN cable. So, some delay must be considered before files are transferred. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 20: Login Settings For Web Access & Ftp

    (\ and /) cannot be used as the password ! The default password is “admin”. The option /W<xxxxxxxx> can be added to set the Wi-Fi password. This Wi-Fi password must be minimal 8 characters long. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 21: Ntp And Date+Time Settings

    For the time, the entered format must be hour, minutes and seconds, separated by the colon-sign and always 8 characters long in total. The new date and time are set after pressing Save & Logout. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 22: Isdn Pri Settings

    Pass-Through mode the wiring in the cables must be right. In other words, when the local and remote phone numbers are reversed in the archiving software, this parameter can be enabled. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 23 +32 = Disable action from call that are in the numberlist. +64 = DTMF is detected from the remote side, else local side. After start-recording, the notification is played (NOTIFY.WAV). After stop-recording, the system beeps are played (BEEPS.WAV). V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 24: Black/White-List Numbers

    (up to 100), it is also possible to make a list of numbers on the PC and put them in a text file, called BLACK.TXT or WHITE.TXT. See further the chapter Number-list. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 25: Special Settings & Commands

    = Record Early; start recording when ringing. ".IN" = Disable connected number for the number-list. ".IM" = Disable remote number for the number-list. ".IB<sec>" = Notification Beep interval in seconds, using "NBEEP.WAV". V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 26 = Set Timeout for the TCP web server (default 90). ".WK<secs>" = Keep-alive timer for the Wi-Fi Tunnel connection (def 60). ".WUP" = Try to update the Wi-Fi module. ".WZ0/1" = Disable/Enable Wi-Fi module during recording. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 27 Note: During the time tracing is active, recording is NOT possible! A step-by-step description of how to make a trace is described in the chapter D-channel trace for debug. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 28: Licenses & Versions

    Ethernet network is an unique identifier that is needed to route the packets over the LAN. The serial number and MAC address are both shown for information purposes and cannot be changed. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 29: Led's

    PC. Red LED steady ON plus Amber steady ON. • This can happen as soon as a call starts, and the system has no Recording Channel Licenses. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 30: Green Link Led

    The link to the Tunnel server is OK. Green LED OFF. • The only normal situation with the Green LED OFF is, when no Tunnel server is defined in the settings. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 31: Blue Data Led

    Amber LED blinking fast (Red LED ON): SD card ERROR. • A read- or write-error happened on the SD card or the SD card is not usable by the system. The card must be removed and checked. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 32: Button Functions

    NOTE: When the Blue LED is not blinking, then no recording is busy, so no data is written, in which case the SD card can just be taken out. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 33: Disable Dhcp Temporary

    When Red or Blue is not blinking at all in between Green going OFF-ON, it means the zero digit. • After the last digit, the system waits 5 seconds and then continues normal operation. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 34: Copy Settings From Sd Card

    Power On and hold the button pressed for 1 second. • The IP address is now on the default value 192.168.55.66 • Only access with FTP is now possible (no web interface). V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 35: Temporary Access With Wi-Fi

    In the login page, enter "admin" and "admin". • The settings page now appears. • After Save & Logout, Wi-Fi is disabled again. • To enable access permanently, enable Wi-Fi Access Point. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 36: Firmware Update

    When the system is accessible through FTP, the firmware can be updated with the PC tool ‘vcUpdater’. This tool can be found on the Vidicode website in the menu Service and Support > Firmware. Another way to update is by using an SD card as follows: - The manufacturer must provide the necessary files first.

  • Page 37: Sd Card Usage

    . Press the button for 2 seconds (Amber & Blue LED OFF). . Release the button (Amber LED flashing). . Take out the SD card or the USB cable (power off). V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 38: Special Sd Card Settings

    By default, the WAV files on the SD card can be played by any media player. By enabling the file encryption, the files only produce noise. The file encryption uses the same Encryption Password as the Tunnel encryption. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 39 SD card. The default is good for most of the cards on the market. Valid speeds to enter: 1 till 12, 15, 17, 20, 24, 25, 30, 40, 50 and 60. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 40 V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...
  • Page 41 “.FF” setting. The read-counter can be set back to resend files. For example, “.CR0” will resend all recorder files from the card to the Tunnel server. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 42: Notification & System Messages

    Then the system reboots and the new messages are used. 2. With FTP: Connect to the V-Tap with FTP and upload your .WAV file(s). V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 43: Number-List (Black- Or White-List)

    • It is also possible to enter the last (right-most) digits only of each number. But then, all entries must have the same length! • The wildcard character “*” can be used to denote a range (79347*). V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 44: Telnet Connection

    A better way to get a D-channel trace is described further on in the manual in the chapter D-channel trace for debug. Telnet is disabled by entering “.DT” in Special Settings & Commands. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 45: Remote Control With Udp Commands

    10 Remote control with UDP commands The V-Tap ISDN PRI can send information and receive commands over the network, using UDP packets. The UDP packets are only activated when this is enabled in the V-Tap. To enable UDP packets do the following: - On the PC edit a text file, called VMON.TXT...
  • Page 46 Char.81 – 83 = Apresa Channel Licenses (only in WAV header) Char.84 – 86 = PC Channel Licenses (only in WAV header) UDP command packets, received by the V-Tap ISDN PRI A command is a simple text string. After receiving a command, the V-Tap always sends back a reply string.

  • Page 47: Channel Trace For Debug

    Commands and the settings saved again. The trace file DTEST.TXT is written to SD card or can • be download with FTP. For analysis, it can be sent to support@vidicode.com V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 48: Isdn Pri Rj45 Connectors & Wiring

    PBX. It has shown that this is also the situation for many other countries. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 49: Revision History

    September 2018 • Page numbers on the right side & Recording Licenses removed. v1.1 July 2018 • Small changes in the text. v1.0 April 2018 • First release. V-Tap ISDN PRI Manual EN v1.23 Nov 2021 © 2018-2021 Vidicode...

  • Page 50: Acknowledgements

    Call Recorder. Vidicode is not a source of official interpretation of laws of any country or state and shall not be construed as a source for making decisions whether to provide notification or not.

This manual is also suitable for:

V-tap isdn bri

Table of Contents