ALLIANCE AR105M_X_CONTROL Installation Operation & Maintenance page 6

Cabinet hardmount
Table of Contents

Advertisement

Safety Information
Never operate the washer with any guards, panels and/or parts
removed or broken. DO NOT bypass any safety devices or
tamper with the controls.
Use washer only for its intended purpose, washing textiles.
Never wash machine parts or automotive parts in the ma-
chine. This could result in serious damage to the basket or
tub.
Use only low-sudsing, no-foaming types of commercial deter-
gent. Be aware that hazardous chemicals may be present.
Wear hand and eye protection when adding detergents and
chemicals. Always read and follow manufacturer's instruc-
tions on packages of laundry and cleaning aids. Heed all
warnings or precautions. To reduce the risk of poisoning or
chemical burns, keep them out of the reach of children at all
times [preferably in a locked cabinet].
Do not use fabric softeners or products to eliminate static un-
less recommended by the manufacturer of the fabric softener
or product.
To avoid machine corrosion and component failure, do not
use corrosive chemicals in the machine. Warranty claims rela-
ted to damage caused by corrosive chemicals will be denied.
Always follow the fabric care instructions supplied by the tex-
tile manufacturer.
Loading door MUST BE CLOSED any time the washer is to
fill, tumble or spin. DO NOT bypass the loading door switch
by permitting the washer to operate with the loading door
open. Do not attempt to open the door until the washer has
drained and all moving parts have stopped.
Be aware that hot water is used to flush the supply dispenser.
Avoid opening the dispenser lid while the machine is running.
Do not attach anything to the supply dispenser's nozzles, if
applicable. The air gap must be maintained.
Do not operate the machine without the water reuse plug or
water reuse system in place, if applicable.
Be sure water connections have a shut-off valve and that fill
hose connections are tight. CLOSE the shut-off valves at the
end of each wash day.
Keep washer in good condition. Bumping or dropping the
washer can damage safety features. If this occurs, have wash-
er checked by a qualified service person.
DANGER: Before inspecting or servicing machine, power
supply must be turned OFF. The servicer needs to wait for at
least 10 minutes after turning the power OFF and needs to
check for residual voltage with a voltage meter. The inverter
remains charged with high voltage for some time after power-
ing OFF. This is an imminently hazardous situation that, if not
avoided, will cause severe personal injury or death. Before
starting inspection of the inverter, check for residual voltage
across main circuit terminals + and -. This voltage must be
below 30 VDC before the servicer can access the inverter for
inspection.
Do not repair or replace any part of the washer, or attempt any
servicing unless specifically recommended in the user-mainte-
nance instructions or in published user-repair instructions that
the user understands and has the skills to carry out. ALWAYS
©
Copyright, Alliance Laundry Systems LLC -
DO NOT COPY or TRANSMIT
disconnect the washer from electrical, power and water sup-
plies before attempting any service.
Disconnect the power by turning off the circuit breaker or by
unplugging the machine. Replace worn power cords.
Before the washer is removed from service or discarded, re-
move the door to the washing compartment.
To avoid premature bearing failure, do not operate the ma-
chine while the basket is empty.
Failure to install, maintain, and/or operate this washer accord-
ing to the manufacturer's instructions may result in conditions
which can produce bodily injury and/or property damage.
Use manufacturer-authorized spare parts to avoid safety haz-
ards.
Adequate ventilation has to be provided to avoid the backflow
of gases into the room from appliances burning other fuels.
The use of hypochlorite will cause corrosion which may cause
component failure under certain circumstances.
The warranty of the machine cannot be accepted in case cor-
rosion was caused by chlorine and chlorine compounds im-
pact.
NOTE: The WARNING and IMPORTANT SAFETY IN-
STRUCTIONS appearing in this manual are not meant
to cover all possible conditions and situations that may
occur. Observe and be aware of other labels and pre-
cautions that are located on the machine. They are in-
tended to provide instruction for safe use of the ma-
chine. Common sense, caution and care must be exer-
cised when installing, maintaining, or operating the
washer.
Always contact your dealer, distributor, service agent or the man-
ufacturer on any problems or conditions you do not understand.
NOTE: For European Union member states only: Elec-
trical safety of the washers described in this manual is
in compliance with the requirements of the European
standard EN60204-1.
Electrical shock hazard will result in death or serious
injury. Disconnect electric power and wait ten (10)
minutes before servicing.
6
DANGER
Part No. D1599ENR14
W911

Hide quick links:

Advertisement

Table of Contents
loading

This manual is also suitable for:

Ar105m_x_control plusAr105n_x_controlAr105n_x_control_plusAr135m_x_controlAr135m_x_control_plusAr135n_x_control ... Show all

Table of Contents