Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for ALLIANCE UW50P4
Summary of Contents for ALLIANCE UW50P4
- Page 1 Washer-Extractors Pocket Hardmount WE-4, WE-5 Control UW50P4 PHM516N PHM516N Keep These Instructions for Future Reference. (If this machine changes ownership, this manual must accompany machine.) Part No. F232160 www.comlaundry.com September 2002...
-
Page 3: Table Of Contents
All rights reserved. No part of the contents of this book may be reproduced or transmitted in any form or by any means without the expressed written consent of the publisher. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 4 Notes © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT F232160...
-
Page 5: Introduction
DO NOT attempt to move Nameplate the machine by pushing on sides. Always use a pry bar or other device at the bottom of the machine. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 6 Notes F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 7: Safety Information
8. Do not reach into the washer if the wash drum is moving. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 8 If this occurs, have washer checked by a qualified service person. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 9: Installation
Shell Front Door Handle Door Box Door Box Door Hinge Switch Door Latch Door Hinge Cam Cage Wrap Spray Rinse Tube Side Panel Control Module Figure 1 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 10: Specifications And Dimensions
0.6 HP and 3.5 HP 208-240 3 Phase Spray Flush-Drain Speed 75 RPM Spray Rinse-Drain Speed 350 RPM Extract Speed 700 RPM G Force During Final Extraction 222 Gs F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 11: Dimensional Clearances
We reserve the right to make changes at any time without notice. A qualified professional engineer should be consulted to determine local conditions prior to installation. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 12 1/2 in. NPT Steam Inlet (Excavate under existing floor. Pour new Supply connections are inside valve box. concrete in pyramid shape.) Compacted Clean Fill Dirt Figure 2 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 13: Machine Foundation
FRONT 2 in. 0.75 in. 31.62 in. (51 mm) (19 mm) (803 mm) 2 in. (51 mm) 35.62 in. (905 mm) MOUNTING BOLT LAYOUT PHM191N Figure 4 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 14: Mechanical Installation
Figure 5 5. After grout has hardened, place the lockwashers and nuts on the bolts and tighten the base firmly to the floor. Check and retighten as necessary. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 15: Water Connection
J-Box. Without proper grounding, personal injury from shock may occur and machine malfunctions may be evident. NOTE: Computer models MUST have a proper ground to prevent computer malfunctions. W452 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 16 Improper installation will result in voiding the warranty. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 17: Perma Automatic Lubricant Injector
Nylon Activating Screw date is during the third month of 1985. Activating Peller Plastic Cap Electrolyte Expandable Bladder Piston Seal Lubricant Reservoir Pipe Thread Temporary Plug Figure 7 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 18: Installation Instructions
Perma lubricators require about 30 hours to develop operating pressure. In those applications where completely uninterrupted lubrication is required, Perma should be activated in advance of installation. PHM537N PHM537N Figure 10 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... -
Page 19: External Supply Connections
L-2 115VAC L-1 TO L-2 220VAC NOTE: NOT FUSED PHM539N PHM539N Tube Connections to Supply Dispenser Decal Remove Plug and Bring Wires Through Hole Terminal Strip Figure 11 F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 20 Notes F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...
-
Page 21: Maintenance
If the level is set too low, the switch will not return to the empty position after the drain is opened. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT... - Page 22 Extra linty or stringy items should only be washed in laundry nets to prevent fouling the seal. F232160 © Copyright, Alliance Laundry Systems LLC – DO NOT COPY or TRANSMIT...