Cabletron Systems CyberSWITCH CSX5500 Quick Start Manual
Central site remote access switch
Hide thumbs
Also See for CyberSWITCH CSX5500:
- User manual (729 pages) ,
- User manual (178 pages) ,
- Release note (9 pages)
Table of Contents
Advertisement
Quick Links
Download this manual
See also:
User Manual
Advertisement
Table of Contents
Related Manuals for Cabletron Systems CyberSWITCH CSX5500
Summary of Contents for Cabletron Systems CyberSWITCH CSX5500
- Page 1 ENTRAL EMOTE CCESS WITCH UICK TART Release 7.4 Cabletron Systems (603) 332-9400 phone (603) 337-3075 fax support@ctron.com...
- Page 2 QUICK START Only qualified personnel should perform installation procedures. CAUTION NOTICE You may post this document on a network server for public use as long as no modifications are made to the document. Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior notice.
-
Page 3: Fcc Notice
Operation of this equipment in a residential area is likely to cause interference in which case the user will be required to correct the interference at his own expense. Central Site Remote Access Switch... - Page 4 QUICK START WARNING: Changes or modifications made to this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. DOC NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digital apparatus set out in the Radio Interference Regulations of the Canadian Department of Communications.
-
Page 5: Table Of Contents
IPX Router to IPX Router Configuration Configuration for Site “Central” Configuration for Site “Remote” IPX Router to Bridge Configuration Configuration for Site “Central” Configuration for Site “Remote” AppleTalk Router to Bridge Configuration Configuration for Site “Central” Configuration for Site “Remote” Central Site Remote Access Switch... - Page 6 QUICK START Connecting a Central Site Product to a Terminal Adapter/Modem IP Router with Digital Modem to a Terminal Adapter/Modem Configuration for Site “Central” Configuration for Site "Remote" on Windows NT 4.0 Configuration of Site “Remote” on Windows 95 IPX Router with Digital Modem to a Terminal Adapter/Modem Configuration for Site “Central”...
-
Page 7: Using Quick Start
SING UICK TART Quick Start is recommended only for those users who are experienced with hardware and software installation procedures. Quick Start is divided into two parts. • Basics This chapter gives detailed instructions on the initial installation steps that are required for all CyberSWITCH configurations. -
Page 8: Basics
ASICS NSTALLING ARDWARE There is a possibility that your distributor has already completed hardware installation. If hardware installation has not been completed, follow the instructions listed below. WARNING: Anytime you remove the module cover, make sure the power cord is not plugged in. Failure to do so may result in personal injury or equipment damage. -
Page 9: Accessing The Cyberswitch
You can use a standard RS232 cable with a null-modem device for direct attachment between the administration console PC and the CyberSWITCH. If you are using remote attachment, connect the administration console PC and the system to their respective modems. ONSOLE ONSOLE ONSOLE Central Site Remote Access Switch ASICS Accessing the CyberSWITCH... -
Page 10: Login On The Cyberswitch
If you want to attach remotely to the system using modems, you must change these settings by using the CCINSTAL program. Refer to the Remote Management chapter of the User’s Guide for details on running this program. SWITCH OGIN ON THE YBER Once you have a connection to the CyberSWITCH, you will be presented with a prompt to enter your log in id. -
Page 11: Upgrading System Software
The first section of the Release Notes will be displayed. You will be given a choice of reviewing the Release Notes, or proceeding with the upgrade. We recommend that you review the Release Notes for release highlights and important information related to this release. NSTRUCTIONS Central Site Remote Access Switch ASICS Upgrading System Software... -
Page 12: Remote Upgrade
QUICK START Use <page down> and <page up> to view sections of the Release Notes. At anytime, you may press the <escape> key to continue with the installation. Follow the on-screen instructions to continue with the upgrade. After 2-3 minutes, you will be asked to select the platform type you are installing from a displayed list. -
Page 13: Handling Upgrade Warnings And Errors
Use Dynamic Management’s manage mode to carry out either of these functions. To enter the manage mode, type manage at the system prompt. If you have no need for these types of RRORS ECURE YSTEM Central Site Remote Access Switch ASICS Change Defaults to Secure System... -
Page 14: Initial Installation Steps
QUICK START devices (PPP devices), simply delete these two devices. At the manage mode prompt, enter the following command: device delete Follow the on-screen instructions for deleting each device. To change the preconfigured devices’ names and secrets to secure the access to the system, enter the following command at the manage mode prompt: device change Follow the prompts to change the device name and secret for User1 and User2. -
Page 15: Physical Resource Configuration
If you have a 4 port basic rate adapter, configure all basic rate lines at this time (up to four lines) • select point-to-point for the interface type • add a data link (two for DMS and NI-1 switch types) • use Automatic TEIs for these data links For Primary Rate: •... -
Page 16: Connectivity
RODUCT TO A routing, and AppleTalk routing "Central" ISDN steps. ORKGROUP RODUCT VIA IP routing with an configurations. CSX1200 WORKGROUP REMOTE ACCESS SWITCH "Remote" B-CHANNELS E1 ONLY B9 B11 B13 B15 B17 B19 B21 B23 B25 B27 POWER SERVICE 10BASE-T... -
Page 17: Configuration For Site "Remote
Set your System Name (Remote). This matches up with Remote device information configured on Central. b. Set your System Secret (Remote_S). This matches up with Remote device information configured on Central. Connecting a Central Site Product to a Workgroup Product via PPP " steps. Central Site Remote Access Switch ONNECTIVITY... -
Page 18: Ip Router To Ip Router Configuration
Set your System Secret (Central_S). This matches up with Central device information configured on Remote. CyberSWITCH ONFIGURATION ISDN "Remote" "Central" LAN IP Address 201.1.2.1 Phone 13135552222 " steps. CSX1200 WORKGROUP REMOTE ACCESS SWITCH B-CHANNELS E1 ONLY POWER SERVICE 10BASE-T B9 B11 B13 B15 B17 B19 B21 B23 B25 B27 B10 B12... -
Page 19: Configuration For Site "Remote
199.2.2.0 LAN. When you configure a static route to a site that uses a unnumbered interface you must enter the device name of the next hop device, Central in this case. Connecting a Central Site Product to a Workgroup Product via PPP " steps. Central Site Remote Access Switch ONNECTIVITY... -
Page 20: Ipx Router To Ipx Router Configuration
Optional: Configure Calling Line Ids (if Calling Line Id security was enabled). d. Under IPX Information: • enable IPX • enable Make Calls for IPX data CyberSWITCH ONFIGURATION Network #11111111 Network # 33333333 WORKGROUP REMOTE ACCESS SWITCH "Central" "Remote" ISDN " steps. FILESER2 Node # 0409A0222222 IN # 978901* CSX1200... -
Page 21: Configuration For Site "Remote
Triggered RIP/SAP with a WAN peer type of ACTIVE from the Routing Protocol option. Note: By using triggered RIP/SAP, you do not need to configure static routes or services. Connecting a Central Site Product to a Workgroup Product via PPP " steps. Central Site Remote Access Switch ONNECTIVITY... -
Page 22: Appletalk Router To Appletalk Router Configuration
Enter Engineering as the port’s default zone name. • Enter Marketing as the second zone name. CyberSWITCH OUTER ONFIGURATION "Remote" ISDN " steps. CSX1200 WORKGROUP REMOTE ACCESS SWITCH B-CHANNELS E1 ONLY B9 B11 B13 B15 B17 B19 B21 B23 B25 B27 POWER SERVICE 10BASE-T... -
Page 23: Configuration For Site "Remote
Accept the default of none for the suggested AppleTalk address. • Enter Remote.Engineering as the port’s default zone name. • Enter Remote.Marketing as the second zone name. Connecting a Central Site Product to a Workgroup Product via PPP " steps. Central Site Remote Access Switch ONNECTIVITY... -
Page 24: Connecting A Central Site Product To A Csx100 Via Ppp
QUICK START Under AppleTalk Port Information, configure a WAN UnNumbered port: • Select the WAN UnNumbered port type. d. Under AppleTalk Static Routes, configure a static route to Central: • Enter Extended for Central’s network type (the default). • Enter 10-13 as the destination network range (Central’s network range). •... -
Page 25: Configuration For Site "Central
(192.168.254.1), DNS address and Domain Name to be sent to a PC when an IP address is requested. d. Select your switch type. Enter the directory number for the CSX100 (13135552222). Click Next. Enable IP Routing by clicking in the box. Click Next. -
Page 26: Ipx Router To Ipx Router Configuration
QUICK START Define Central’s phone settings. Enter 13135551111. d. Optional: Define Caller ID Numbers if Caller ID Security was enabled. Click Next. Configure a default route to Central. Click Default Route. Enable Network Address Translation. Click Advanced, and then Yes. Enable Network Address Translation by clicking in the box. -
Page 27: Configuration For Site "Remote
Set the Hop Count (2). • Set the Node address (000000000001). • Accept the External WAN Network Number (00000000). • Click OK. Click Save. Connecting a Central Site Product to a CSX100 via PPP ” Central Site Remote Access Switch ONNECTIVITY... -
Page 28: Ipx Router To Bridge Configuration
QUICK START IPX R OUTER TO RIDGE ONFIGURATION Using the IPX WAN Remote LAN feature provides easy set up for the network administrator, especially if there are multiple remote sites. FILESER1 Node # 0409A0111111 IN # 432109* CSX5500 Phone # 13135551111 IN # 123456* * IN # = Internal Network Number “C... -
Page 29: Configuration For Site "Remote
Select the LAN port type. Connecting a Central Site Product to a CSX100 via PPP ” ONFIGURATION ISDN ” steps. Central Site Remote Access Switch ONNECTIVITY CSX100 "Remote" C A B L E T R O N S Y S T E M S... -
Page 30: Configuration For Site "Remote
Accept the Local Ethernet IP Address. Click Next. b. Set your CyberSWITCH Name (Remote) and System Password (Remote_S). Select your switch type. d. Enter the directory number for the CSX100 (13135552222). Click Next twice. Define Central as a remote connection. -
Page 31: Connecting A Central Site Product To A Terminal Adapter/Modem
• installing remote access networking Connecting a Central Site Product to a Terminal Adapter/Modem RODUCT TO A ERMINAL ERMINAL DAPTER ” steps. " NT 4.0 INDOWS Central Site Remote Access Switch ONNECTIVITY DAPTER ODEM routing ODEM... - Page 32 QUICK START • configuring a dial-out location • adding a dial-up entry Note: Installing a terminal adapter/modem is not described in this document. Install Remote Access Networking (first-time installation only) To successfully negotiate and connect with the network, you need to set up protocols and network services, as well as specify the system’s identity: Open Control Panel and double click Network.
- Page 33 Click OK to return to previous menu. Script tab: Ensure After dialing (login) option is set to None. b. Before dialing... options may remain at default settings. Connecting a Central Site Product to a Terminal Adapter/Modem Central Site Remote Access Switch ONNECTIVITY...
- Page 34 QUICK START Security tab: Select option Accept any authentication including clear text. X.25 tab: Ensure the Network setting is (none). Your phone book entry setup is now complete. Click OK. Make a Connection to the Remote Network You are now ready to attempt a connection to the remote network. From the Dial-Up Networking menu, click Dial.
- Page 35 Boxes for software compression and PPP LCP extensions should remain disabled. Click TCP/IP Settings. Click Specify an IP Address and provide your IP address (101.78.1.2). Or, click Obtain an IPaddress automatically. Click OK when finished. Connecting a Central Site Product to a Terminal Adapter/Modem Central Site Remote Access Switch ONNECTIVITY...
- Page 36 QUICK START Dialing Out Double click on your new dialing icon to bring up the Connect To screen. Enter your Remote for your user name and Remote_S for your password. Double click on Connect. Once the call is connected, click Details to view the type of protocols in use. Click Disconnect to disconnect the call.
- Page 37 12. Finally, you will be prompted to restart your system. Click Finish and Yes to reboot your computer. The system should restart and give you the opportunity to login as normal. Your remote access service is now completely installed. Connecting a Central Site Product to a Terminal Adapter/Modem Central Site Remote Access Switch ONNECTIVITY...
- Page 38 QUICK START Add a Dial-Up Entry This final set of instructions details configuration of a phone book entry. It involves: • providing physical information about the network (such as phone number) • specifying type of server • defining how to find and communicate with the remote system To add a new phone book entry: Click Start, Programs, Accessories and then Dial-Up Networking.
- Page 39 10. On the Configuration tab, select Client for NetWare Networks. If necessary, on the General tab specify the preferred server and first network drive letter to use. Connecting a Central Site Product to a Terminal Adapter/Modem ” INDOWS Central Site Remote Access Switch ONNECTIVITY...
- Page 40 QUICK START Setting up a New Number Click Start, Programs, Accessories and then Dial-Up Networking. (Or, you may get to the same location by clicking My Computer, then double clicking on Dial-Up Networking). Double click on Make New Connection: Provide name of the computer you are dialing. b.
- Page 41 PPP resources rupgrade.bat security securing the system signaling type common channel software remote upgrade upgrading software installation synchronization type system defaults changing to secure system TDM BUS tools for configuration Central Site Remote Access Switch NDEX...
- Page 42 QUICK START upgrade.osw upgrading software warnings and errors VCCI notice CyberSWITCH WAN adapters WAN resources adding...