Key Features - C-TEC CAST XFP Engineering Manual

CAST XFP 32 ZONE ANALOGUE ADDRESSABLE FIRE ALARM PANEL

KEY FEATURES

The CAST XFP 1 loop, 32 zone (Part No. XFP501/CA) and CAST XFP 2 loop, 32 zone (Part No. XFP502/CA)
analogue addressable fire alarm panels are designed for use with fire and security systems and offer
the following features:
• Certification by the LPCB to EN54 parts 2 and 4.
• Full compatibility with C-TEC's CAST
proprietary communication p
hort-circuit protected loop drivers (rated at 450mA max, 40V), each capable of supporting up to
• S
255 addressable CAST devices per loop, giving 510 devices for a 2 loop panel.
device is fitted with a
• Two CAST device addressing options - automatically by the panel (AUTO ADDRESS & LOOP LEARN
functions), or manually using the CAST Handheld Programmer (Part No. CAPROG).
Ability to change a device's address.
•
Ability to detect and fix duplicate addresses.
•
Ability to detect swapped loop devices.
•
• Ability to turn all device polling LEDs on/off.
Fast response time from fire detection to multiple output groups.
•
Two independently programmable conventional sounder circuits.
•
Two programmable auxiliary inputs (non-monitored).
•
• A fault relay output and three programmable relay outputs with volt-free changeover contacts.
A selection of zone dependency functions (EN54-2 Clause 7.12, type A, B or C) as detailed below:
•
Type A - If there is an alarm from a detector, the panel will look for a confirmatory alarm from
the same, or another, detector in the same zone before a full alarm is established. If there is no
confirmatory alarm, the first alarm will automatically reset.
Type B - As type A except the confirmatory signal must be from another detector in the same zone.
Type C - As type A except the confirmatory signal may also be from another zone and the first
alarm will not automatically reset.
A day (building occupied) and night (building unoccupied) timing function.
•
• An investigation delay period function (programmable for length of time, which zones it applies
to and whether or not it operates in day/night mode).
• Individual sensitivity settings for each device.
EN54-2 Clause 7.8 re-sounding fire alarm devices.
•
EN54-2 Clause 7.11 delays to outputs and a phased evacuation facility.
•
EN54-2 Clause 7.13 alarm counter to record the number of alarm states (maximum of 999 counts).
•
• EN54-2 Clause 8.3 reporting of faults from heat detectors, optical detectors & multi-detectors.
EN54-2 Clause 9.5 disablements of addressable points individually.
•
An integral 2.5A EN54-4 switched mode PSU.
•
Earth fault monitoring.
•
Keypad code to enter access levels 2 & 3. Keyswitch entry to access level 2.
•
40 characters of custom text per device.
•
Comprehensive EN54-2 Clause 10 test with maintenance and commissioning functions.
•
• Windows based PC programming tools (Part No. XFP507) that MUST be used to configure the system.
Networking (Optional)
If required, the panel can be configured to sit on a non-redundant network of up to eight connected
CAST XFP main panels (any variant), OR you can have up to eight XFP repeaters connected to one
non-networked CAST XFP main panel. FOR NETWORK WIRING 2-CORE SCREENED, ENHANCED FIRE-
RESISTANT CABLE IS RECOMMENDED. If you want to utilise either of these options, the panel will
require a separately available network driver card (Part No. AFP711). See pages 13-14 for details.
ENGINEERING MANUAL • Approved Document No. DFU5010020 Rev 4 • Page 5 of 48
®
(C-TEC Addressable System Technology) - a
rotocol.
short-circuit isolator.
Note: The CAST XFP network and XFP repeaters
have not been assessed to EN54-2.
powerful,
Each CAST Loop