Lectrical Pecifications; Power Supply - Honeywell BC-200 Operation, Installation & Programming Manual

Specifications & Approvals
4.3 E
LECTRICAL
Note: All functions and specifications described in this Operators Manual are subject to change without notice.
4 . 3 . 1 P
4 . 3 . 1 P
O W E
O W E
Parameter
Input Voltage
Input Range
Output Voltage
Adjustable
Range
Rated Current
Of Power Supply
Overload
Current Device
Secondary
Transformer
Fuse
Max Ripple
Load Regulation
Line Regulation
Efficiency
Battery Test
Battery Test
Relay Contact
Rating
Indicators
Status Indicators
Environmental
WARNING: Severe damage may occur if the batteries are connected incorrectly.
Note: When annunciators or field modules are powered from external power supplies, use a separate conductor to
connect the main power supply common terminal (-0V) to the remote power supplies common terminal (-0V).
BC-200 Manual – P/N DOC-01-013
S
PECIFICATIONS
S
S
R U P P L Y
R U P P L Y
PS243 PS249
(3Amp) (9Amp)
240V AC +/- 240V AC +/-
10% 10%
216V AC to 216 V AC to
254V AC 254V AC
24V DC nom. 24V DC nom.
27.6V DC no 27.6V DC no
load load
26.5 V DC full 26.5V DC full
load load
12V DC to 30V 12V DC to 30V
DC DC
3.0A @ 26.5V 9.0A @ 26.5V
DC DC
7.4A @ Short 20A @ Short
Circuit Circuit
5A 15A
150mV p-p 150mV p-p
2% 2%
2% 2%
>80% >80%
Internal: 15 Internal: 15
ohms ohms
10A 15A
Mains On, Mains On,
Output On Output On
By External By External
Interface or FIP Interface or FIP
-10C to +55C -10C to +55C
Dry heat Dry heat
+ 40C @ 93% + 40C @ 93%
RH RH
NPS-2 NPS-5
(2.6amp) (5.5amp)
110 or 240 Universal
(SW select)
85-132/170- 85-264VAC
264VAC Auto Ranging
(SW select)
24V DC nom. 24V DC nom.
27.6V DC no 27.6V DC no
load load
27.3V DC full 27.3V DC full
load load
+/-10% +/-10%
2.6A @ 27V DC 5.5A @ 27V DC
105% to 150% 105% to 150%
of rated power – of rated power –
auto recovery auto recovery
after fault after fault
removal removal
N/A N/A
120mV p-p 150mV p-p
± 0.5% ± 0.5%
± 0.5% ± 0.5%
82% 84%
External Load External Load
N/A N/A
Mains On, Mains On,
Charger Fault, Charger Fault,
Battery Fault, Battery Fault,
Battery test, Battery test,
Batt test inhibit Batt test inhibit
Onboard LED or Onboard LED or
External External
Interface or FIP Interface or FIP
-10C to +55C -10C to +55C
Dry heat Dry heat
+ 40C @ 93% + 40C @ 93%
RH RH
NPS-11
(11.7amp)
Universal
88-264VAC
Auto Ranging
24V DC nom.
27.6V DC no
load
27.3V DC full
load
26V to 32V
11.7 @ 27V DC
105% to 135%
of rated power –
auto recovery
after fault
removal
N/A
200mV p-p
± 0.5%
± 0.2%
88%
External Load
N/A
Mains On,
Charger Fault,
Battery Fault,
Battery test,
Batt test inhibit
Onboard LED or
External
Interface or FIP
-10C to +55C
Dry heat
+ 40C @ 93%
RH
12