Komatsu PC88MR-10 Shop Manual page 1432

Removal and installation of boom swing
bracket..................................................... 50-165
Removal and installation of center swivel joint
assembly.................................................. 50-138
Removal and installation of control valve
assembly.................................................. 50-148
Removal and installation of counterweight
assembly.................................................. 50-136
Removal and installation of cylinder head
assembly.................................................... 50-27
Removal and installation of EGR (Exhaust Gas
Recirculation) cooler assembly..................... 50-71
Removal and installation of EGR (Exhaust Gas
Recirculation) valve assembly ...................... 50-73
Removal and installation of engine and main
pump assembly .......................................... 50-49
Removal and installation of engine controller
assembly.................................................. 50-218
Removal and installation of engine front oil
seal ........................................................... 50-57
Removal and installation of engine hood
assembly.................................................... 50-63
Removal and installation of engine rear oil seal ...50-
58
Removal and installation of fan belt ................ 50-74
Removal and installation of floor frame
assembly.................................................. 50-194
Removal and installation of front window
assembly.................................................. 50-193
Removal and installation of front wiper
assembly.................................................. 50-210
Removal and installation of fuel cooler
assembly.................................................... 50-60
Removal and installation of fuel tank assembly....50-
61
Removal and installation of hydraulic oil cooler
assembly.................................................... 50-43
Removal and installation of hydraulic tank
assembly.................................................. 50-141
Removal and installation of idler and idler
cushion assembly ..................................... 50-124
Removal and installation of injector assembly . 50-20
Removal and installation of KCCV assembly ... 50-67
Removal and installation of KDOC muffler ...... 50-64
Removal and installation of KOMTRAX
terminal .................................................... 50-223
Removal and installation of machine monitor
assembly.................................................. 50-220
Removal and installation of main pump
assembly.................................................. 50-144
Removal and installation of mass air flow and
temperature sensor ................................... 50-222
Removal and installation of operator's cab
assembly.................................................. 50-175
Removal and installation of operator's cab door...50-
179
Removal and installation of operator's cab
glass (adhered glass) ................................ 50-182
Removal and installation of operator's seat ... 50-208
PC88MR-10
Removal and installation of pump controller
assembly.................................................. 50-219
Removal and installation of radiator assembly . 50-39
Removal and installation of revolving frame
assembly.................................................. 50-134
Removal and installation of seat belt............. 50-209
Removal and installation of sprocket ............ 50-123
Removal and installation of starting motor
assembly.................................................. 50-217
Removal and installation of supply pump
assembly.................................................... 50-17
Removal and installation of swing circle
assembly.................................................. 50-121
Removal and installation of swing motor and
swing machinery assembly .........................50-111
Removal and installation of travel motor and
final drive assembly..................................... 50-76
Removal and installation of work equipment
assembly...................................... 50-158, 50-162
ROPS cab.................................................. 10-168
S-1 Engine does not crank when starting
switch is turned to START position.............. 40-515
S-2 Engine cranks but no exhaust smoke
comes out ................................................ 40-516
S-3 Fuel is being injected but engine does not
start (misfiring: engine cranks but does not
start) ........................................................ 40-517
S-4 Engine startability is poor....................... 40-518
S-5 Engine does not pick up smoothly .......... 40-520
S-6 Engine stops during operation................ 40-522
S-7 Engine runs rough or is unstable ............ 40-524
S-8 Engine lacks power............................... 40-525
S-9 Exhaust smoke is black ......................... 40-527
S-10 Engine oil consumption is excessive..... 40-529
S-11 Engine oil becomes contaminated early 40-530
S-12 Fuel consumption is excessive............. 40-531
S-13 Oil is in coolant (or coolant spurts or
coolant level goes down) ........................... 40-532
S-14 Oil pressure drops............................... 40-533
S-15 Fuel mixes into engine oil .................... 40-534
S-16 Water mixes into engine oil (milky)........ 40-535
S-17 Coolant temperature rises too high
(overheating) ............................................ 40-536
S-18 Unusual noise is heard ........................ 40-537
S-19 Vibration is excessive.......................... 40-538
S-20 Air cannot be bled from fuel circuit ........ 40-539
Sensor....................................................... 10-238
Separation and connection of track shoe
assembly.................................................. 50-122
Sequence of events in troubleshooting ........... 40-10
Service Message ........................................ 30-119
Sketch of tools for testing and adjusting ............ 30-6
Sketches of special tools ............................... 50-15
Solenoid valve.................................. 10-147, 60-49
Special functions of machine monitor.............. 30-73
Special tools list............................................ 50-10
INDEX
S
7