6.LW2Programmer'sReference
6.4.7. View Crosspoint Size
Showsthephysicalcrosspointsize.
Command and Response
{getsize•<layer>}
(SIZE=<size>•<layer>)CrLf
Parameters
Identifier
Parameterdescription
<size>
Crosspointsize
<layer>
Signaltypeofthelayer
Example
{GETSIZEAV}
(SIZE=6x1V)
(SIZE=5x1A)
Thedevicereportsthatithasavideocrosspointwith6inputs(Testpatterngeneratoristhe6thinput)and1
outputandanaudiocrosspointwith5inputsand1output.
6.4.8. Change the Video Autoselect Mode
Theautoselectmodeofthevideooutputscanbechanged.
Command and Response
{AS_V<out>=<state>;<mode>}
(AS_V<out>=<state>;<mode>)CrLf
Parameters
Identifier
Parameterdescription
<state>
ShowingtheAutoselectstate
<mode>
Theautoselectmodesetting
Example
{as_v1=E;P}
(AS_V1=E;P)
(AS_V2=E;P)
TheAutoselectmodeofvideooutput1andoutput2isenabledandsettoPrioritymode.Theoutputnumbers
are listed in the
PortNumbering
section.
INFO:
TheAutoselectmodecanbequeriedbytypingthe{as_v<out>=?}command.
Parametervalues
<number_of_inputs>x<number_of_outputs>
Seetheprevioussection
Parametervalues
E: autoselect is enabled
D: autoselect is disabled
F: First detect mode
L:Lastdetectmode
P:Prioritydetectmode
Appliedfirmwarepackage:v1.3.2b3 | LDCsoftware:v2.5.7b2
HDMI-TPS-TX200series–User'sManual
6.4.9. Change the Audio Autoselect Mode
Theautoselectmodeoftheaudiooutputscanbechanged.
Command and Response
{AS_A<out>=<state>;<mode>}
(AS_A<out>=<state>;<mode>)CrLf
Parameters
Seetheprevioussection.
Example
{as_a1=E;P}
(AS_A1=E;P)
(AS_A2=E;P)
TheAutoselectmodeofaudiooutput1andoutput2isenabledandsettoPrioritymode.
INFO:
TheAutoselectmodecanbequeriedbytypingthe{as_v<out>=?}command.
6.4.10. Change the Video Input Priorities
Thesettingsofvideoinputprioritycanbechangedasfollows.
Command and Response
{PRIO_V<out>=<in1_prio>;<in2_prio>;<in3_prio>;<in4_prio>}
(PRIO_V<out>=<in1_prio>;<in2_prio>;<in3_prio>;<in4_prio>)CrLf
Parameters
Identifier
<in1_prio>
<in2_prio>
<in3_prio>
<in4_prio>
SeemoredetailsaboutportnumberinginthePortNumbering
Example
{prio_v1=1;0;2;3}
(PRIO_V1=1;0;2;3)
Input2hasthehighestpriority(0),Input1hasthesecondhighest(1).Input4hasthelowestpriority(3).
ATTENTION!
Always set all the priority of the ports when changing, otherwise, the change will not be
executedandtheresponsewillbethecurrentsetting(likequeryingtheprioritysetting).
INFO:
Inthiscase,theoutputsarelinked;thechangewillaffectbothlocalandTPSoutputports.
INFO:
Thevideoprioritiescanbequeriedbytypingthe{prio_v<out>=?}command.
Parameterdescription
Parametervalues
Prioritynumberoftheinputports
0:highestpriority
between0and3
3: lowest priority
section.
73