Canon Color Image Reader-F1 Service Manual page 74

5
Adjustment > Adjustment (Reader) > Measurement during Reader Controller PCB Replacement and After RAM Clear:
When backup is not performed normally
4) Enter the values written on the service label (on the back of the Reader Front Cover).
Lv. COPIER > ADJUST > ADJ-XY >
1 ADJ-X ADJ-Y-DF
ADJ-Y STRD-POS
Lv. COPIER > ADJUST > CCD >
1 W-PLT-X DFTBK-R
W-PLT-Y DFTBK-G
W-PLT-Z DFTBK-B
SH-TRGT DFTBK-BW
DFTAR-R DFCH2R2
DFTAR-G DFCH2R10
DFTAR-B DFCH2B2
DFTAR-BW DFCH2B10
MTF2-M1 MTF2-M7
MTF2-M2 MTF2-M8
MTF2-M3 MTF2-M9
MTF2-M4 MTF2-M10
MTF2-M5 MTF2-M11
MTF2-M6 MTF2-M12
MTF-M1 MTF-M7
MTF-M2 MTF-M8
MTF-M3 MTF-M9
MTF-M4 MTF-M10
MTF-M5 MTF-M11
MTF-M6 MTF-M12
2 100DF2RG 100DF2GB
Lv. COPIER > ADJUST > PASCAL >
1 OFST-P-Y OFST-P-M
5) Perform the MTF filter coefficient computation.
Lv. COPIER > FUNCTION > CCD >
1 MTF-CLC
6) Perform computation for front & back linearity matching
Lv. COPIER > FUNCTION > CCD >
1 DF-LNR
7) Enter the values written on the service label (on the back of the Reader Front Cover).
Lv. FEEDER > ADJUST >
1 DOCST LA-SPEED
5 Adjustment > Adjustment (Reader) > Measurement during Reader Controller PCB Replacement and After RAM Clear:
ADJ-X-MG ADJY-DF2
- -
DFCH2G2 DFCH-B10
DFCH2G10 DFCH-G2
DFCH2K2 DFCH-G10
DFCH2K10 DFCH-K2
DFCH-R2 DFCH-K10
DFCH-R10 100-RG
DFCH-B2 100-GB
- -
MTF2-S1 MTF2-S7
MTF2-S2 MTF2-S8
MTF2-S3 MTF2-S9
MTF2-S4 MTF2-S10
MTF2-S5 MTF2-S11
MTF2-S6 MTF2-S12
MTF-S1 MTF-S7
MTF-S2 MTF-S8
MTF-S3 MTF-S9
MTF-S4 MTF-S10
MTF-S5 MTF-S11
MTF-S6 MTF-S12
- -
OFST-P-C OFST-P-K
T-5-5
T-5-6
T-5-7
DOCST2 LA-SPD2
T-5-8
8) Adjust tray width. Perform either AB system or Inch system.
a. AB system adjustment.
a-1) Select the item in the service mode.
Lv. FEEDER > FUNCTION >
1 TRY-A4
a-2) Adjust the slide guide to the index "A4/A3".
a-3) Press OK, and register the A4 width.
a-4) Select the item in the service mode.
Lv. FEEDER > FUNCTION >
1 TRY-A5R
a-5) Adjust the slide guide to the index "A5R".
a-6) Press OK, and register the A5R width.
b. Inch system adjustment.
b-1) Select the item in the service mode.
Lv. FEEDER > FUNCTION >
1 TRY-LTR
b-2) Adjust the slide guide to the index "LTR/ 11x17".
b-3) Press OK, and register the letter width.
b-4) Select the item in the service mode.
Lv. FEEDER > FUNCTION >
1 TRY-LTRR
b-5) Adjust the slide guide to the index "STMT/ LTRR/ LGL".
b-6) Press OK, and register the LTRR width.
9) Make an output of P-PRINT.
Lv. COPIER > FUNCTION > MISC-P >
1 P-PRINT
10)Store the outputted P-PRINT into the service book.
T-5-9
T-5-10
T-5-11
T-5-12
T-5-13
5-3
5-3