KidKraft F24145 Installation And Operating Instructions Manual
  1. Manuals
  2. Brands
  3. KidKraft Manuals
  4. Play Sets & Playground Equipment
  5. F24145
  6. Installation and operating instructions manual
KidKraft F24145 Installation And Operating Instructions Manual

KidKraft F24145 Installation And Operating Instructions Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
A INSLEY
PLAY
SYSTEM
F24145
INSTALLATION AND OPERATING INSTRUCTIONS
KidKraft, Inc.
4630 Olin Road
Dallas, Texas 75244 USA
customerservice@kidkraft.com
canadacustomerservice@kidkraft.com
1.800.933.0771
972.385.0100
For online parts replacement visit
https://parts.kidkraft.com/
WARNING
and give them to any future owner of this play system. Manufacturer contact information provided below.
OBSTACLE FREE SAFETY ZONE - 22'3" x 28' area requires Protective Surfacing. See page 3.
MAXIMUM VERTICAL FALL HEIGHT - 6' (1.8 m)
CAPACITY - 6 Users Maximum, Ages 3 to 10; Weight Limit 110 lbs. (49.9 kg) per child.
RESIDENTIAL HOME USE ONLY. Not intended for public areas such as schools, churches, nurseries, day cares or parks.
Warning. Only for domestic use.
KidKraft Netherlands BV
Olympisch Stadion 8
1076 DE Amsterdam
The Netherlands
europecustomerservice@kidkraft.com
+31 20 305 8620 M-F from 09:00 to 17:30
(GMT+1)
For online parts replacement visit
https://parts.kidkraft.eu/
To reduce the risk of serious injury or death, you must read and
follow these instructions. Keep and refer to these instructions often

Table of Contents

Warnings And Safe Play Instructions. . . . . . . . . . . . . . . pg. 2
Protective Surfacing Guidelines. . . . . . . . . . . . . . . . . . . pg. 3
Instructions For Proper Maintenance . . . . . . . . . . . . . . . pg. 4
About Our Wood – Limited Warranty . . . . . . . . . . . . . . pg. 5
Keys To Assembly Success . . . . . . . . . . . . . . . . . . . . . . pg. 6
Part ID . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . pg. 7
Installation of I.D./Warning Plaque . . . . . . . . . . . .Final Step
9404145
4 - 8 Hrs
Two person
assembly
Rev 07/03/2020

Advertisement

Table of Contents
loading

Related Manuals for KidKraft F24145

Summary of Contents for KidKraft F24145

  • Page 1 Protective Surfacing Guidelines....pg. 3 KidKraft, Inc. KidKraft Netherlands BV Olympisch Stadion 8 Instructions for Proper Maintenance ....pg. 4...
  • Page 2 Warnings and Safe Play Instructions CONTINUOUS ADULT SUPERVISION REQUIRED. Most serious injuries and deaths on playground equipment have occurred while children were unsupervised! Our products are designed to meet mandatory and voluntary safety standards. Complying with all warnings and recommendations in these instructions will reduce the risk of serious or fatal injury to children using this play system.
  • Page 3 Protective Surfacing - Reducing Risk of Serious Head Injury From Falls. One of the most important things you can do to reduce the likelihood of serious head injuries is to install shock-absorbing protective surfacing under and around your play equipment. The protective surfacing should be applied to a depth that is suitable for the equipment height in accordance with ASTM F1292.
  • Page 4 Instructions for Proper Maintenance Your KidKraft Play System is designed and constructed of quality materials with your child’s safety in mind. As with all outdoor products used by children, it will weather and wear. To maximize the enjoyment, safety and life of your Play Set, it is important that you, the owner, properly maintain it.
  • Page 5 About Our Wood KidKraft Premium Play Systems uses only premium playset lumber, ensuring the safest product for your children’s use. Although we take great care in selecting the best quality lumber available, wood is still a product of nature and susceptible to weathering which can change the appearance of your set.
  • Page 6 Keys to Assembly Success Tools Required • 3/16” Hex Key • Tape Measure • #1, #3 Phillips or Robertson • Open End Wrench • Carpenters Level bit or Screwdriver (1/2”, 7/16” & 9/16”) • 8’ Step Ladder • Carpenters Square •...
  • Page 7 Your Key To Quick Assembly SORTING WOOD PARTS INTO EACH ASSEMBLY STEP WILL SAVE TIME! Step Step Step SAVE TIME - TIP #1: Open each box with wood parts and look for the Key Number stamped on the end of the wood part (see chart below). Sort each wood part into the different assembly steps.
  • Page 8 Part Identification (Reduced Size) WOOD CHART (5) CE Floor Board 1 x 4 x 32-1/2" Nominal Size Actual Size ⅜ 1½" x 5 " 2" x 6" 0304 3630304 Box 1 ⅜ ⅜ " x 3 " 2" x 4" ⅜...
  • Page 9 Part Identification (Reduced Part Size) WOOD CHART Nominal Size (1) Tarp Support 1 x 2 x 26-7/8" Actual Size ⅜ 1½" x 5 " 3641750 Box 1 2" x 6" 1750 ⅜ " x 3 ⅜ " 2" x 4" ⅜...
  • Page 10 Part Identification (Reduced Part Size) (1) Floor Joist 5/4 x 2 x 38-1/2" 3641763 Box 1 1763 (1) Floor Front 2 x 3 x 38-1/2" 3641764 Box 1 1764 (2) Rock Rail 2 x 3 x 42-3/4" 3641765 Box 1 1765 (3) Corner Block 2 x 3 x 4-1/2"...
  • Page 11 Hardware Identification (Actual Size) (2) Pan Bolt 1/4 x 1 1/4" 9274211 Lock Washer 1/4" Flat Washer 1/4" T-Nut (2) Hex Bolt 1/4 x 1 1/2" 9277212 1/4" Lock Washer - 1/4" Flat Washer - 1/4" T-Nut (22) Hex Bolt 1/4 x 2" 9277220 1/4"...
  • Page 12 Hardware Identification (Actual Size) 9277320 (2) Hex Bolt 5/16 x 2" 2-5/16" Flat Washer, 1- 5/16" Lock Nut 9262230 (3) Lag Screw 1/4 x 3" -1/4" Flat Washer (24) Flat Head Screw #8 x 1 1/8" (52042514) (18) #8 Flat Washer (9251500) (59) Flat Head Screw #8 x 1 1/2"...
  • Page 13 Before you discard your cartons fill out the form below. • The carton I.D. stamp is located on the end of each carton.The tracking number is located on the KidKraft ID Plaque (9320374). • Please retain this information for future reference. You will need this information if you contact the Consumer Relations Department.
  • Page 14 Step 1: Swing Beam Assembly Fig. 1.3 Hex Bolt Assembly Warning: For your childs safety, Lock T- Nut orientate the swing hangers as Washer shown to ensure your swing will have proper swing motion when installed. Failure to do so could Flat He x Washer...
  • Page 15 Step 2: Swing End Assembly Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: Attach 2 (1749) SW Posts to (1756) SW Upright using 2 (G4) 5/16 x 4” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 2.1) B: Attach (1755) SW Support to both (1749) SW Posts and (1756) SW Upright using 3 (G5) 5/16 x 4-1/2” Hex Bolts (with lock washer, flat washer and t-nut). (fig. 2.1) Fig 2.1 1755 1749 1756 1749 Hardware Wood Parts 5/16 x 4” Hex Bolt SW Post 2 x 4 x 79-1/2” 1749 (5/16”...
  • Page 16 Step 3: Swing Beam Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: Place (4919) SW Rail Block in the centre between (1773) CE SW Beam Front and (1772) CE SW Beam Back and attach beams with 1 (H8) 1/4 x 4-1/4” Hex Bolt (with flat washer, lock washer and t-nut). (fig. 3.1 & 3.2) B: Attach Swing Beam Assembly to the side of the Swing End Assembly with the overhang (fig. 3.3) using 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) in the top hole of Triangle Plate and 1 (G8) 5/16 x 2” Hex Bolt (with 2 flat washers and lock nut) in the bottom hole of Triangle Plate. (fig. 3.3) Make sure Swing End Assembly flares out at an angle. (fig 3.4) Fig. 3.1 4919 1773 Fig. 3.2 1772 Fig. 3.4 Fig. 3.3 Side with Overhang Hardware Wood Parts 1/4 x 4-1/4” Hex Bolt SW Rail Block 2 x 4 x 5-3/8”...
  • Page 17 Step 4: Swing Side Assembly Predrill Pilot Holes for Lag Screw Hex Bolt Assembly Note: Pre-drill all holes using a 1/8” drill bit before installing Lock Lag Predrill 1/8” T- Nut Washer Screw pilot hole the lag screws. Flat Use factory drilled Flat He x Washer hole as a guide Washer Bolt A: To 2 (1771) Posts attach (1770) SW Ground and (1759) SW Floor using 4 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut) in each board. Be sure to keep bolts loose. (fig. 4.1) Fig. 4.1 1759 1771 1770 Notice hole...
  • Page 18 Step 5: Wall Side Assembly Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: To 2 (1771) Posts attach (1760) Floor and (1769) Ground Side with 4 (H2) 1/4 x 2” Bolts (with lock washer, flat washer and t-nut) per board. (fig. 5.1) Back Notice hole towards back 1753 1771 Fig. 5.1 1760 1769 B: Attach (1753) Top End to each (1771) Post with 2 (H2) 1/4 x 2” Hex Bolts (with lock washer, flat washer and t-nut). These Hex Bolts are to be installed from the back of the assembly. (fig. 5.1) C: Attach (1766) Corner Block flush to angled extension of (1769) Ground Side with 2 (S2) 8 x 1-1/2” Wood Screws as shown in fig. 5.2. 1753 Fig. 5.2 Fig. 5.3 1769 1766 Wood Parts Hardware Post 2 x 4 x 74”...
  • Page 19 Step 6: Front Frame Assembly Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: Attach (1764) Floor Front to (1771) Posts with 2 (H6) 1/4 x 4-3/4” Bolt (with flat washer, lock washer and t- nut). Hex Bolts to be installed from the inside of the assembly. (fig. 6.2) B: Attach (1752) Top Front to (1771) Posts with 4 (S7) 12 x 2” Pan Screws (with 3/16” flat washer). (1752) Top Front should be flush to the top of each (1771) Post. (fig. 6.1 & 6.2) Notice hole Fig. 6.2 towards top Slide wall side 1748 1752 Swing wall side Fig. 6.1 1760 1771 1771 Parts removed for clarity 1764 1759 Notice hole towards bottom Wood Parts Hardware...
  • Page 20 Step 7: Rock Rail Assembly A: Attach (1766) Corner Block 1/2” from bottom of (1765) Rock Rail with 2 (S3) 8 x 2-1/2” Wood Screws as shown in fig. 7.1. B: Make sure assembly is square and then attach (1765) Rock Rail with Corner Block to (1764) Floor Front with 2 (S15) #8 x 1-3/4” Wood Screws. Top of (1765) Rock Rail angled edge should be flush to the top of (1764) Floor Front. (fig. 7.2 & 7.3) C: Attach (1770) SW Ground to (1765) Rock Rail with 2 (S2) #8 x 1-1/2” Wood Screws as shown in fig. 7.2 & 7.4. Fig. 7.1 1765 Flush Fig. 7.3 1766 1/2” Fig. 7.2 1764 1765 1764 1765 Fig. 7.4 1770 1765 1770 Hardware Wood Parts #8 x 2-1/2” Wood Screw Corner Block 2 x 3 x 4-1/2” 1766 Rock Rail 2 x 3 x 42-3/4”...
  • Page 21 Step 8: Attach Centre Divider Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: Attach (1751) Centre Divider to (1752) Top Front with 1 (H2) 1/4 x 2” Bolt (with flat washer, lock washer and t-nut) from outside of the assembly and to (1764) Floor Front with 1 (H11) 1/4 x 2-3/4” Bolt (with flat washer, lock washer and t-nut) from inside the assembly. (fig. 8.1) 1752 1752 1751 1764 1751 1764 Fig. 8.1 Wood Parts Hardware Centre Divider 2 x 2 x 38” 1751 1/4 x 2” Hex Bolt (1/4”...
  • Page 22 Step 9: Attach Gusset A: Make sure assembly is square and then place 1 (0312) Gusset tight to the under side of (1764) Floor Front and to (1771) Post from the inside of the assembly. Make sure the gusset is flush to the outside of the post and attach with 2 (S4) #8 x 3” Wood Screws per side. (fig. 9.1, 9.2 & 9.3) Fig. 9.2 1764 Fig. 9.1 1771 0312 1764 1771 Flush to outside edge Fig. 9.3 0312 1771 Hardware Wood Parts Gusset 2 x 3 x 16” #8 x 3” Wood Screw 0312...
  • Page 23 Step 10: Attach Lower Front A: Attach (1767) Lower Front flush to the top of (1766) Corner Block at (1769) Ground Side with 2 (S15) #8 x 1-3/4” Screws. (fig. 10.1 & 10.2) B: Make sure (1767) Lower Front is level and then attach to (1765) Rock Rail with 2 (S15) #8 x 1-3/4” Screws. (fig. 10.1) Fig. 10.1 1769 1765 Notice hole orientation towards top 1766 1767 1767 Flush to top Fig. 10.2 Hardware Wood Parts #8 x 1-3/4” Wood Screw Lower Front 1 x 6 x 39-3/4” 1767...
  • Page 24 Step 11: Floor Back Assembly A: Attach (1762) Floor Back to (1761) Side Joist with 2 (H3) 1/4 x 2-1/2” Bolts (with flat washer, lock washer and t-nut) and 2 (S7) 12 x 2” Pan Screws (with flat washers) as shown in fig. 11.1. (1761) Side Joist should be flush to the top of (1762) Floor Back. Bolts to be installed on (1761) Side Joist side and screws installed from (1762) Floor Back side. Fig. 11.1 1761 1762 Hardware Wood Parts #12 x 2 Pan Screw (with 3/16” flat washer) Side Joist 2 x 2 x 34-3/4” 1761 Floor Back 5/4 x 4 x 38-5/8” 1762 1/4 x 2-1/2”...
  • Page 25 Step 12: Floor Back Assembly Predrill Pilot Holes for Lag Screw Hex Bolt Assembly Pre-drill all pilot holes using a Lock Lag Predrill 1/8” T- Nut Washer Screw pilot hole 1/8” drill bit before installing the lag screws. Flat Use factory drilled Flat He x Washer hole as a guide Washer Bolt A: On the back side of the assembly attach (1768) Lower Back flush to the bottom and outside edge of (1771) Posts with 2 (LS3) 1/4 x 3” Lag Screws (with flat washer) in the top, pre-drilled holes and 2 (S7) 12 x 2” Pan Screws (with 3/16” flat washer) in the bottom holes as shown in fig. 12.1 & 12.3.
  • Page 26 Step 12: Floor Back Assembly cont. Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt C: Attach 2 (0359) Front Dividers to (1762) Floor Back with 1 (H1) 1/4 x 1-1/2” Hex Bolt (with lock washer, flat washer and t-nut) per board. Be sure to keep bolts loose. (fig. 12.4 & 12.6) D: Attach each (0359) Front Divider to (1758) Top Back using 1 (PB2) 1/4 x 1-1/4” Pan Bolt (with lock washer, flat washer and t-nut) per board. Be sure to keep bolts loose. (fig. 12.4 & 12.5) E: Level and attach (1758) Top Back to both (1771) Posts using 4 (S7) #12 x 2” Pan Screws (with 3/16” flat wash- ers). (fig. 12.7) Fig. 12.5 Fig. 12.4 1758 1758 Hole towards top...
  • Page 27 Step 13: Chalk Wall Assembly A: Place the Chalk Wall Tarp in between each (0359) Front Divider and (1758) Top Back. Make sure tarp is taut and then attach to (1758) Top Back with 3 (S5) #8 x 1/2” Wood Screws (with #8 flat washer). Tighten the bolts in both (0359) Front Dividers. (fig. 13.1) B: Recheck that tarp is taut and then attach Chalk Wall Tarp to both (0359) Front Dividers from the inside of the assembly with 2 (S5) #8 x 1/2” Pan Screws (with #8 flat washer) per board as shown in fig. 13.2. C: 3” above (1762) Floor Back attach (1754) Lower Back Wall to each (0359) Front Divider with 4 (S1) #8 x 1-1/8” Wood Screws. (fig. 13.3) D: Attach Chalk Wall Tarp to (1754) Lower Back Wall with 3 (S5) #8 x 1/2” Wood Screws (with #8 flat washer). (fig. 13.4) Fig. 13.2 Fig. 13.1 1758 0359 0359 0359 0359 Fig. 13.4 1754 Fig. 13.3 0359 3” 0359 1762 1754 Other Parts Hardware Wood Parts 1 x Chalk Wall Tarp 10 x #8 x 1/2 Pan Screw (with #8 flat washer) Lower Back Wall 1 x 4 x 31-1/2”...
  • Page 28 Step 14: Floor Frame Assembly A: From inside of the assembly, measure 3-1/8” down from the top of (1759) SW Floor (fig. 14.2) and (1760) Floor (fig. 14.3) and then attach (1763) Floor Joist to each board with 1 (S4) #8 x 3” Wood Screws per end. Make sure the (1763) Floor Joist is installed with the 1-3/8” side facing up. (fig. 14.1 & 14.2) Fig. 14.2 1757 1759 3-1/8” 1-3/8” 1763 Fig. 14.1 1759 1760 1760 3-1/8” 1763 Fig. 14.3 Wood Parts Hardware Floor Joist 5/4 x 2 x 38-1/2” 1763 #8 x 3” Wood Screw...
  • Page 29 Step 15: Attach Floor Boards A: Install 1 (1774) CE Gap Board to each end of the assembly attaching to (1761) Side Joist, (1763) Floor Joist and (1764) Front Floor using 5 (S2) #8 x 1-1/2” Wood Screws per board. Make sure boards are tight to (1759) SW Floor, (1760) Floor, (1762) Floor Back and each (1771) Post. (fig. 15.1) B: In between both (1774) CE Gap Boards place 5 (1776) Floor Boards making sure all boards are evenly spaced. Attach to (1761) Side Joist, (1763) Floor Joist and (1764) Front Floor using 5 (S2) #8 x 1-1/2” Wood Screws per board. All boards should be tight to (1762) Floor Back. (fig. 15.2) C: Tight to (1751) Centre Divider and flush to top of (1776) Floor Board attach (1766) Corner Block to (1764) Floor Front with 2 (S3) #8 x 2-1/2” Wood Screws. (fig. 15.2 & 15.3) x 5 per board 1761 1771 Fig. 15.1 1760 1763 1759 1764 1774 1771 1774 Fig. 15.3 1764 Fig. 15.2 1751 1762 1766 1776 1776 1776 1776 1776 1766 x 5 per board 1764 Hardware Wood Parts...
  • Page 30 Step 16: Attach Ground Stakes MOVE FORT TO FINAL LOCATION. FINAL LOCATION MUST BE ON LEVEL GROUND A: Drive 2 (0318) Ground Stakes 10-1/2” into the ground at the 2 (1771) Posts on (1770) SW Ground as shown in fig.16.1. Attach using 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 16.1) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines.
  • Page 31 Step 17: Wall Assembly A: On the Swing Side Wall attach 2 (0304) CE Floor Boards on either side of the (1757) Wall Mount with 4 (S1) #8 x 1 1/8” Wood Screws per board. Make sure the bottom of the boards are 1” up from the (1774) CE Gap Boards and there is approximately 3” between each (1771) Post and (0304) CE Floor Board, not exceed- ing 3-1/4”. (fig. 17.1 & 17.2) B: On the opposite wall attach 3 (0304) CE Floor Boards between the 2 (1771) Posts with 4 (S1) #8 x 1-1/8” Wood Screws per board. Make sure the bottom of the boards are 1” up from the (1774) CE Gap Board and there is approximately 2-1/2” between each board, not exceeding 2-3/4”. (fig. 17.3 & 17.4) 3“ Fig. 17.2 1771 3“ Fig. 17.1 1771 0304 1774 2-1/2“ 1771 x 4 per board 0304 Fig. 17.4 Fig. 17.3 1771 1774 1“ Wood Parts Hardware CE Floor Board 1 x 4 x 32-1/2” 20 x #8 x 1-1/8”...
  • Page 32 Step 18: Canopy Roof Assembly A: Feed both Canopy Tubes through each sleeve of the Canopy Roof until it reaches the mid point, then insert the Canopy Tubes through the holes in (1750) Tarp Support and bring it up to the centre line. (fig. 18.1) B: Continue feeding Canopy Tubes through the rest of the Canopy Roof sleeves and then insert the ends of the tubes into tube holders. The flat side of the tube holders should face inwards. Make sure the notched out holes in the Canopy Roof are at the centre line. (fig. 18.1 & 18.2) C: Place Canopy Roof on fort at (1748) SW Top and (1753) Top End as shown in fig. 18.3. The tube holders should be 5/8” from outside edge and 3/4” from top of (1748) SW Top and (1753) Top End. (fig. 18.4) Pre-drill holes for the screws and then attach tube holders to each board with the 4 (S10) #8 x 1” Pan Screws per tube holder. (fig. 18.3) Canopy tube Fig. 18.2 Fig. 18.1 1750 Canopy sleeve Top of holder Centre line Bottom of holder 1750 Tube holder Fig. 18.3 3/4” Fig. 18.4 1748 5/8” x 4 per corner 1753 Other Parts Hardware Wood Parts Canopy 16 x #8 x 1”...
  • Page 33 Step 18: Canopy Roof Assembly cont. D: Loosen the top bolt in (1757) Wall Mount, tuck Canopy Roof in between fort and (1757) Wall Mount and then secure Canopy Roof to (1748) SW Top and (1753) Top End with 4 (S5) #8 x 1/2” Pan Screws (with #8 flat wash- er) per board. Be sure to re-tighten bolt in (1757) Wall Mount. (fig. 18.5) Fig. 18.5 x 4 per side 1748 1753 Hardware #8 x 1/2” Pan Screw (#8 flat washer)
  • Page 34 Step 19: Attach Rock Rail A: Attach 1 (1765) Rock Rail 17” from the already installed (1765) Rock Rail to (1764) Floor Front and (1767) Lower Front with 4 (S15) #8 x 1-3/4” Wood Screws. Top of (1765) Rock Rail angled edge should be to the top of (1764) Floor Front.
  • Page 35 Step 20: Attach Slide A: Beside Rock Wall, centre slide in opening between (1751) Centre Divider and (1771) Post. B: Pre-drill 1/8” pilot holes and attach slide to fort through the floor boards and into (1764) Floor Front using 2 (S7) #12 x 2” Pan Screws. (fig. 20.1 & 20.2) 1751 Fig. 20.1 Fig. 20.2 1764 Other Parts Hardware 1 x Slide #12 x 2” Pan Screw...
  • Page 36 Step 21: Attach Swing To Fort Hex Bolt Assembly Lock T- Nut Washer Flat He x Washer Bolt A: Attach Swing Assembly from Step 3 to (1757) Wall Mount with 1 (G5) 5/16 x 4-1/2” Hex Bolt (with lock washer, flat washer and t-nut) and 1 (G8) 5/16 x 2” Hex Bolt (with 2 flat washers and 1 lock nut) as shown in fig. 21.1 & 21.2. Fig. 21.1 Fig. 21.2 Lock washer T-nut Flat washer 1757 Lock nut Flat washer Hardware 5/16 x 4-1/2” Hex Bolt (5/16” lock washer, 5/16” flat washer, 5/16” t-nut) 5/16 x 2”...
  • Page 37 Step 22: Attach Ground Stakes to Swing End A: Drive 1 (0318) Ground Stake 10-1/2” into the ground at each (1749) SW Post on the inside of the assembly and attach with 2 (S3) #8 x 2-1/2” Wood Screws per ground stake. (fig. 22.1 & 22.2) WARNING: To prevent tipping and avoid potential injury, stakes must be driven 10-1/2” into ground. Digging or driving stakes can be dangerous if you do not check first for underground wiring, cables or gas lines.
  • Page 38 Step 23: Attach Swings A: Attach 2 Belt Swings to the Bolt-Thru Swing Hangers. (fig. 23.1) Fig. 23.1 Belt swings Other Parts 2 x Belt Swing...
  • Page 39 Final Step: Attach I.D. Plaque ATTACH THIS WARNING & I.D. PLAQUE TO A PROMINENT LOCATION ON YOUR PLAY EQUIPMENT! (Fort or Swing Post) This provides warnings concerning safety and important contact information. A Tracking Number is provided to allow you to get critical information or order replacement parts for this specific model Attach with (S5) #8 x 1/2"...
  • Page 40 NOTES...
  • Page 41 Would you recommend the purchase of our products to friends and family? Comments: MAIL TO: Fill out your registration card online at KidKraft https://prdregistration.kidkraft.com/ 4630 Olin Road Dallas, TX 75244 United States KidKraft would like to say Thank You for Attention: Customer Service your time and feedback.

Table of Contents